FreeBSD/Linux Kernel Cross Reference
sys/Documentation/pci.txt

                              How To Write Linux PCI Drivers
     
                        by Martin Mares <mj@ucw.cz> on 07-Feb-2000
     
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     The world of PCI is vast and it's full of (mostly unpleasant) surprises.
     Different PCI devices have different requirements and different bugs --
     because of this, the PCI support layer in Linux kernel is not as trivial
     as one would wish. This short pamphlet tries to help all potential driver
    authors to find their way through the deep forests of PCI handling.
    
    
    0. Structure of PCI drivers
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~
    There exist two kinds of PCI drivers: new-style ones (which leave most of
    probing for devices to the PCI layer and support online insertion and removal
    of devices [thus supporting PCI, hot-pluggable PCI and CardBus in single
    driver]) and old-style ones which just do all the probing themselves. Unless
    you have a very good reason to do so, please don't use the old way of probing
    in any new code. After the driver finds the devices it wishes to operate
    on (either the old or the new way), it needs to perform the following steps:
    
            Enable the device
            Access device configuration space
            Discover resources (addresses and IRQ numbers) provided by the device
            Allocate these resources
            Communicate with the device
    
    Most of these topics are covered by the following sections, for the rest
    look at <linux/pci.h>, it's hopefully well commented.
    
    If the PCI subsystem is not configured (CONFIG_PCI is not set), most of
    the functions described below are defined as inline functions either completely
    empty or just returning an appropriate error codes to avoid lots of ifdefs
    in the drivers.
    
    
    1. New-style drivers
    ~~~~~~~~~~~~~~~~~~~~
    The new-style drivers just call pci_register_driver during their initialization
    with a pointer to a structure describing the driver (struct pci_driver) which
    contains:
    
            name            Name of the driver
            id_table        Pointer to table of device ID's the driver is
                            interested in.  Most drivers should export this
                            table using MODULE_DEVICE_TABLE(pci,...).
                            Set to NULL to call probe() function for every
                            PCI device known to the system.
            probe           Pointer to a probing function which gets called (during
                            execution of pci_register_driver for already existing
                            devices or later if a new device gets inserted) for all
                            PCI devices which match the ID table and are not handled
                            by the other drivers yet. This function gets passed a
                            pointer to the pci_dev structure representing the device
                            and also which entry in the ID table did the device
                            match. It returns zero when the driver has accepted the
                            device or an error code (negative number) otherwise.
                            This function always gets called from process context,
                            so it can sleep.
            remove          Pointer to a function which gets called whenever a
                            device being handled by this driver is removed (either
                            during deregistration of the driver or when it's
                            manually pulled out of a hot-pluggable slot). This
                            function always gets called from process context, so it
                            can sleep.
            save_state      Save a device's state before it's suspend.
            suspend         Put device into low power state.
            resume          Wake device from low power state.
            enable_wake     Enable device to generate wake events from a low power
                            state.
    
                            (Please see Documentation/power/pci.txt for descriptions
                            of PCI Power Management and the related functions)
    
    The ID table is an array of struct pci_device_id ending with a all-zero entry.
    Each entry consists of:
    
            vendor, device  Vendor and device ID to match (or PCI_ANY_ID)
            subvendor,      Subsystem vendor and device ID to match (or PCI_ANY_ID)
            subdevice
            class,          Device class to match. The class_mask tells which bits
            class_mask      of the class are honored during the comparison.
            driver_data     Data private to the driver.
    
    When the driver exits, it just calls pci_unregister_driver() and the PCI layer
    automatically calls the remove hook for all devices handled by the driver.
    
    Please mark the initialization and cleanup functions where appropriate
    (the corresponding macros are defined in <linux/init.h>):
    
            __init          Initialization code. Thrown away after the driver
                            initializes.
            __exit          Exit code. Ignored for non-modular drivers.
            __devinit       Device initialization code. Identical to __init if
                            the kernel is not compiled with CONFIG_HOTPLUG, normal
                            function otherwise.
            __devexit       The same for __exit.
    
   Tips:
           The module_init()/module_exit() functions (and all initialization
           functions called only from these) should be marked __init/exit.
           The struct pci_driver shouldn't be marked with any of these tags.
           The ID table array should be marked __devinitdata.
           The probe() and remove() functions (and all initialization
           functions called only from these) should be marked __devinit/exit.
           If you are sure the driver is not a hotplug driver then use only 
           __init/exit __initdata/exitdata.
   
           Pointers to functions marked as __devexit must be created using
           __devexit_p(function_name).  That will generate the function
           name or NULL if the __devexit function will be discarded.
   
   
   2. How to find PCI devices manually (the old style)
   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
   PCI drivers not using the pci_register_driver() interface search
   for PCI devices manually using the following constructs:
   
   Searching by vendor and device ID:
   
           struct pci_dev *dev = NULL;
           while (dev = pci_find_device(VENDOR_ID, DEVICE_ID, dev))
                   configure_device(dev);
   
   Searching by class ID (iterate in a similar way):
   
           pci_find_class(CLASS_ID, dev)
   
   Searching by both vendor/device and subsystem vendor/device ID:
   
           pci_find_subsys(VENDOR_ID, DEVICE_ID, SUBSYS_VENDOR_ID, SUBSYS_DEVICE_ID, dev).
   
      You can use the constant PCI_ANY_ID as a wildcard replacement for
   VENDOR_ID or DEVICE_ID.  This allows searching for any device from a
   specific vendor, for example.
   
      In case you need to decide according to some more complex criteria,
   you can walk the list of all known PCI devices yourself:
   
           struct pci_dev *dev;
           pci_for_each_dev(dev) {
                   ... do anything you want with dev ...
           }
   
   For compatibility with device ordering in older kernels, you can also
   use pci_for_each_dev_reverse(dev) for walking the list in the opposite
   direction.
   
   
   3. Enabling devices
   ~~~~~~~~~~~~~~~~~~~
      Before you do anything with the device you've found, you need to enable
   it by calling pci_enable_device() which enables I/O and memory regions of
   the device, assigns missing resources if needed and wakes up the device
   if it was in suspended state. Please note that this function can fail.
   
      If you want to use the device in bus mastering mode, call pci_set_master()
   which enables the bus master bit in PCI_COMMAND register and also fixes
   the latency timer value if it's set to something bogus by the BIOS.
   
      If you want to use the PCI Memory-Write-Invalidate transaction,
   call pci_set_mwi().  This enables bit PCI_COMMAND bit for Mem-Wr-Inval
   and also ensures that the cache line size register is set correctly.
   Make sure to check the return value of pci_set_mwi(), not all architectures
   may support Memory-Write-Invalidate.
   
   4. How to access PCI config space
   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      You can use pci_(read|write)_config_(byte|word|dword) to access the config
   space of a device represented by struct pci_dev *. All these functions return 0
   when successful or an error code (PCIBIOS_...) which can be translated to a text
   string by pcibios_strerror. Most drivers expect that accesses to valid PCI
   devices don't fail.
   
      If you access fields in the standard portion of the config header, please
   use symbolic names of locations and bits declared in <linux/pci.h>.
   
      If you need to access Extended PCI Capability registers, just call
   pci_find_capability() for the particular capability and it will find the
   corresponding register block for you.
   
   
   5. Addresses and interrupts
   ~~~~~~~~~~~~~~~~~~~~~~~~~~~
      Memory and port addresses and interrupt numbers should NOT be read from the
   config space. You should use the values in the pci_dev structure as they might
   have been remapped by the kernel.
   
      See Documentation/IO-mapping.txt for how to access device memory.
   
      You still need to call request_region() for I/O regions and
   request_mem_region() for memory regions to make sure nobody else is using the
   same device.
   
      All interrupt handlers should be registered with SA_SHIRQ and use the devid
   to map IRQs to devices (remember that all PCI interrupts are shared).
   
   
   6. Other interesting functions
   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
   pci_find_slot()                 Find pci_dev corresponding to given bus and
                                   slot numbers.
   pci_set_power_state()           Set PCI Power Management state (0=D0 ... 3=D3)
   pci_find_capability()           Find specified capability in device's capability
                                   list.
   pci_module_init()               Inline helper function for ensuring correct
                                   pci_driver initialization and error handling.
   pci_resource_start()            Returns bus start address for a given PCI region
   pci_resource_end()              Returns bus end address for a given PCI region
   pci_resource_len()              Returns the byte length of a PCI region
   pci_set_drvdata()               Set private driver data pointer for a pci_dev
   pci_get_drvdata()               Return private driver data pointer for a pci_dev
   pci_set_mwi()                   Enable Memory-Write-Invalidate transactions.
   pci_clear_mwi()                 Disable Memory-Write-Invalidate transactions.
   
   
   7. Miscellaneous hints
   ~~~~~~~~~~~~~~~~~~~~~~
   When displaying PCI slot names to the user (for example when a driver wants
   to tell the user what card has it found), please use pci_dev->slot_name
   for this purpose.
   
   Always refer to the PCI devices by a pointer to the pci_dev structure.
   All PCI layer functions use this identification and it's the only
   reasonable one. Don't use bus/slot/function numbers except for very
   special purposes -- on systems with multiple primary buses their semantics
   can be pretty complex.
   
   If you're going to use PCI bus mastering DMA, take a look at
   Documentation/DMA-mapping.txt.
   
   
   8. Obsolete functions
   ~~~~~~~~~~~~~~~~~~~~~
   There are several functions kept only for compatibility with old drivers
   not updated to the new PCI interface. Please don't use them in new code.
   
   pcibios_present()               Since ages, you don't need to test presence
                                   of PCI subsystem when trying to talk with it.
                                   If it's not there, the list of PCI devices
                                   is empty and all functions for searching for
                                   devices just return NULL.
   pcibios_(read|write)_*          Superseded by their pci_(read|write)_*
                                   counterparts.
   pcibios_find_*                  Superseded by their pci_find_* counterparts.

Cache object: b75c174e6ba90cdd6c0204a971fd79b3