FreeBSD/Linux Kernel Cross Reference
sys/cam/cam.h
1 /*-
2 * Data structures and definitions for the CAM system.
3 *
4 * Copyright (c) 1997 Justin T. Gibbs.
5 * All rights reserved.
6 *
7 * Redistribution and use in source and binary forms, with or without
8 * modification, are permitted provided that the following conditions
9 * are met:
10 * 1. Redistributions of source code must retain the above copyright
11 * notice, this list of conditions, and the following disclaimer,
12 * without modification, immediately at the beginning of the file.
13 * 2. The name of the author may not be used to endorse or promote products
14 * derived from this software without specific prior written permission.
15 *
16 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
17 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
18 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
19 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
20 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
21 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
22 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
23 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
24 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
25 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
26 * SUCH DAMAGE.
27 *
28 * $FreeBSD: releng/10.1/sys/cam/cam.h 259204 2013-12-10 22:55:22Z nwhitehorn $
29 */
30
31 #ifndef _CAM_CAM_H
32 #define _CAM_CAM_H 1
33
34 #ifdef _KERNEL
35 #include <opt_cam.h>
36 #endif
37
38 #include <sys/cdefs.h>
39
40 typedef u_int path_id_t;
41 typedef u_int target_id_t;
42 typedef u_int lun_id_t;
43 typedef union {
44 u_int64_t lun64;
45 u_int8_t lun[8];
46 } lun64_id_t;
47
48 #define CAM_XPT_PATH_ID ((path_id_t)~0)
49 #define CAM_BUS_WILDCARD ((path_id_t)~0)
50 #define CAM_TARGET_WILDCARD ((target_id_t)~0)
51 #define CAM_LUN_WILDCARD ((lun_id_t)~0)
52
53 #define CAM_EXTLUN_BYTE_SWIZZLE(lun) ( \
54 ((((u_int64_t)lun) & 0xffff000000000000L) >> 48) | \
55 ((((u_int64_t)lun) & 0x0000ffff00000000L) >> 16) | \
56 ((((u_int64_t)lun) & 0x00000000ffff0000L) << 16) | \
57 ((((u_int64_t)lun) & 0x000000000000ffffL) << 48))
58
59 /*
60 * Maximum length for a CAM CDB.
61 */
62 #define CAM_MAX_CDBLEN 16
63
64 /*
65 * Definition of a CAM peripheral driver entry. Peripheral drivers instantiate
66 * one of these for each device they wish to communicate with and pass it into
67 * the xpt layer when they wish to schedule work on that device via the
68 * xpt_schedule API.
69 */
70 struct cam_periph;
71
72 /*
73 * Priority information for a CAM structure.
74 */
75 typedef enum {
76 CAM_RL_HOST,
77 CAM_RL_BUS,
78 CAM_RL_XPT,
79 CAM_RL_DEV,
80 CAM_RL_NORMAL,
81 CAM_RL_VALUES
82 } cam_rl;
83 /*
84 * The generation number is incremented everytime a new entry is entered into
85 * the queue giving round robin per priority level scheduling.
86 */
87 typedef struct {
88 u_int32_t priority;
89 #define CAM_PRIORITY_HOST ((CAM_RL_HOST << 8) + 0x80)
90 #define CAM_PRIORITY_BUS ((CAM_RL_BUS << 8) + 0x80)
91 #define CAM_PRIORITY_XPT ((CAM_RL_XPT << 8) + 0x80)
92 #define CAM_PRIORITY_DEV ((CAM_RL_DEV << 8) + 0x80)
93 #define CAM_PRIORITY_OOB (CAM_RL_DEV << 8)
94 #define CAM_PRIORITY_NORMAL ((CAM_RL_NORMAL << 8) + 0x80)
95 #define CAM_PRIORITY_NONE (u_int32_t)-1
96 u_int32_t generation;
97 int index;
98 #define CAM_UNQUEUED_INDEX -1
99 #define CAM_ACTIVE_INDEX -2
100 #define CAM_DONEQ_INDEX -3
101 #define CAM_EXTRAQ_INDEX INT_MAX
102 } cam_pinfo;
103
104 /*
105 * Macro to compare two generation numbers. It is used like this:
106 *
107 * if (GENERATIONCMP(a, >=, b))
108 * ...;
109 *
110 * GERERATIONCMP uses modular arithmetic to guard against wraps
111 * wraps in the generation number.
112 */
113 #define GENERATIONCMP(x, op, y) ((int32_t)((x) - (y)) op 0)
114
115 /* CAM flags XXX Move to cam_periph.h ??? */
116 typedef enum {
117 CAM_FLAG_NONE = 0x00,
118 CAM_EXPECT_INQ_CHANGE = 0x01,
119 CAM_RETRY_SELTO = 0x02 /* Retry Selection Timeouts */
120 } cam_flags;
121
122 enum {
123 SF_RETRY_UA = 0x01, /* Retry UNIT ATTENTION conditions. */
124 SF_NO_PRINT = 0x02, /* Never print error status. */
125 SF_QUIET_IR = 0x04, /* Be quiet about Illegal Request reponses */
126 SF_PRINT_ALWAYS = 0x08, /* Always print error status. */
127 SF_NO_RECOVERY = 0x10, /* Don't do active error recovery. */
128 SF_NO_RETRY = 0x20 /* Don't do any retries. */
129 };
130
131 /* CAM Status field values */
132 typedef enum {
133 /* CCB request is in progress */
134 CAM_REQ_INPROG = 0x00,
135
136 /* CCB request completed without error */
137 CAM_REQ_CMP = 0x01,
138
139 /* CCB request aborted by the host */
140 CAM_REQ_ABORTED = 0x02,
141
142 /* Unable to abort CCB request */
143 CAM_UA_ABORT = 0x03,
144
145 /* CCB request completed with an error */
146 CAM_REQ_CMP_ERR = 0x04,
147
148 /* CAM subsystem is busy */
149 CAM_BUSY = 0x05,
150
151 /* CCB request was invalid */
152 CAM_REQ_INVALID = 0x06,
153
154 /* Supplied Path ID is invalid */
155 CAM_PATH_INVALID = 0x07,
156
157 /* SCSI Device Not Installed/there */
158 CAM_DEV_NOT_THERE = 0x08,
159
160 /* Unable to terminate I/O CCB request */
161 CAM_UA_TERMIO = 0x09,
162
163 /* Target Selection Timeout */
164 CAM_SEL_TIMEOUT = 0x0a,
165
166 /* Command timeout */
167 CAM_CMD_TIMEOUT = 0x0b,
168
169 /* SCSI error, look at error code in CCB */
170 CAM_SCSI_STATUS_ERROR = 0x0c,
171
172 /* Message Reject Received */
173 CAM_MSG_REJECT_REC = 0x0d,
174
175 /* SCSI Bus Reset Sent/Received */
176 CAM_SCSI_BUS_RESET = 0x0e,
177
178 /* Uncorrectable parity error occurred */
179 CAM_UNCOR_PARITY = 0x0f,
180
181 /* Autosense: request sense cmd fail */
182 CAM_AUTOSENSE_FAIL = 0x10,
183
184 /* No HBA Detected error */
185 CAM_NO_HBA = 0x11,
186
187 /* Data Overrun error */
188 CAM_DATA_RUN_ERR = 0x12,
189
190 /* Unexpected Bus Free */
191 CAM_UNEXP_BUSFREE = 0x13,
192
193 /* Target Bus Phase Sequence Failure */
194 CAM_SEQUENCE_FAIL = 0x14,
195
196 /* CCB length supplied is inadequate */
197 CAM_CCB_LEN_ERR = 0x15,
198
199 /* Unable to provide requested capability*/
200 CAM_PROVIDE_FAIL = 0x16,
201
202 /* A SCSI BDR msg was sent to target */
203 CAM_BDR_SENT = 0x17,
204
205 /* CCB request terminated by the host */
206 CAM_REQ_TERMIO = 0x18,
207
208 /* Unrecoverable Host Bus Adapter Error */
209 CAM_UNREC_HBA_ERROR = 0x19,
210
211 /* Request was too large for this host */
212 CAM_REQ_TOO_BIG = 0x1a,
213
214 /*
215 * This request should be requeued to preserve
216 * transaction ordering. This typically occurs
217 * when the SIM recognizes an error that should
218 * freeze the queue and must place additional
219 * requests for the target at the sim level
220 * back into the XPT queue.
221 */
222 CAM_REQUEUE_REQ = 0x1b,
223
224 /* ATA error, look at error code in CCB */
225 CAM_ATA_STATUS_ERROR = 0x1c,
226
227 /* Initiator/Target Nexus lost. */
228 CAM_SCSI_IT_NEXUS_LOST = 0x1d,
229
230 /* SMP error, look at error code in CCB */
231 CAM_SMP_STATUS_ERROR = 0x1e,
232
233 /*
234 * Command completed without error but exceeded the soft
235 * timeout threshold.
236 */
237 CAM_REQ_SOFTTIMEOUT = 0x1f,
238
239 /*
240 * 0x20 - 0x32 are unassigned
241 */
242
243 /* Initiator Detected Error */
244 CAM_IDE = 0x33,
245
246 /* Resource Unavailable */
247 CAM_RESRC_UNAVAIL = 0x34,
248
249 /* Unacknowledged Event by Host */
250 CAM_UNACKED_EVENT = 0x35,
251
252 /* Message Received in Host Target Mode */
253 CAM_MESSAGE_RECV = 0x36,
254
255 /* Invalid CDB received in Host Target Mode */
256 CAM_INVALID_CDB = 0x37,
257
258 /* Lun supplied is invalid */
259 CAM_LUN_INVALID = 0x38,
260
261 /* Target ID supplied is invalid */
262 CAM_TID_INVALID = 0x39,
263
264 /* The requested function is not available */
265 CAM_FUNC_NOTAVAIL = 0x3a,
266
267 /* Nexus is not established */
268 CAM_NO_NEXUS = 0x3b,
269
270 /* The initiator ID is invalid */
271 CAM_IID_INVALID = 0x3c,
272
273 /* The SCSI CDB has been received */
274 CAM_CDB_RECVD = 0x3d,
275
276 /* The LUN is already enabled for target mode */
277 CAM_LUN_ALRDY_ENA = 0x3e,
278
279 /* SCSI Bus Busy */
280 CAM_SCSI_BUSY = 0x3f,
281
282
283 /*
284 * Flags
285 */
286
287 /* The DEV queue is frozen w/this err */
288 CAM_DEV_QFRZN = 0x40,
289
290 /* Autosense data valid for target */
291 CAM_AUTOSNS_VALID = 0x80,
292
293 /* SIM ready to take more commands */
294 CAM_RELEASE_SIMQ = 0x100,
295
296 /* SIM has this command in it's queue */
297 CAM_SIM_QUEUED = 0x200,
298
299 /* Quality of service data is valid */
300 CAM_QOS_VALID = 0x400,
301
302 /* Mask bits for just the status # */
303 CAM_STATUS_MASK = 0x3F,
304
305 /*
306 * Target Specific Adjunct Status
307 */
308
309 /* sent sense with status */
310 CAM_SENT_SENSE = 0x40000000
311 } cam_status;
312
313 typedef enum {
314 CAM_ESF_NONE = 0x00,
315 CAM_ESF_COMMAND = 0x01,
316 CAM_ESF_CAM_STATUS = 0x02,
317 CAM_ESF_PROTO_STATUS = 0x04,
318 CAM_ESF_ALL = 0xff
319 } cam_error_string_flags;
320
321 typedef enum {
322 CAM_EPF_NONE = 0x00,
323 CAM_EPF_MINIMAL = 0x01,
324 CAM_EPF_NORMAL = 0x02,
325 CAM_EPF_ALL = 0x03,
326 CAM_EPF_LEVEL_MASK = 0x0f
327 /* All bits above bit 3 are protocol-specific */
328 } cam_error_proto_flags;
329
330 typedef enum {
331 CAM_ESF_PRINT_NONE = 0x00,
332 CAM_ESF_PRINT_STATUS = 0x10,
333 CAM_ESF_PRINT_SENSE = 0x20
334 } cam_error_scsi_flags;
335
336 typedef enum {
337 CAM_ESMF_PRINT_NONE = 0x00,
338 CAM_ESMF_PRINT_STATUS = 0x10,
339 CAM_ESMF_PRINT_FULL_CMD = 0x20,
340 } cam_error_smp_flags;
341
342 typedef enum {
343 CAM_EAF_PRINT_NONE = 0x00,
344 CAM_EAF_PRINT_STATUS = 0x10,
345 CAM_EAF_PRINT_RESULT = 0x20
346 } cam_error_ata_flags;
347
348 struct cam_status_entry
349 {
350 cam_status status_code;
351 const char *status_text;
352 };
353
354 extern const struct cam_status_entry cam_status_table[];
355 extern const int num_cam_status_entries;
356 #ifdef _KERNEL
357 extern int cam_sort_io_queues;
358 #endif
359 union ccb;
360
361 #ifdef SYSCTL_DECL /* from sysctl.h */
362 SYSCTL_DECL(_kern_cam);
363 #endif
364
365 __BEGIN_DECLS
366 typedef int (cam_quirkmatch_t)(caddr_t, caddr_t);
367
368 caddr_t cam_quirkmatch(caddr_t target, caddr_t quirk_table, int num_entries,
369 int entry_size, cam_quirkmatch_t *comp_func);
370
371 void cam_strvis(u_int8_t *dst, const u_int8_t *src, int srclen, int dstlen);
372
373 int cam_strmatch(const u_int8_t *str, const u_int8_t *pattern, int str_len);
374 const struct cam_status_entry*
375 cam_fetch_status_entry(cam_status status);
376 #ifdef _KERNEL
377 char * cam_error_string(union ccb *ccb, char *str, int str_len,
378 cam_error_string_flags flags,
379 cam_error_proto_flags proto_flags);
380 void cam_error_print(union ccb *ccb, cam_error_string_flags flags,
381 cam_error_proto_flags proto_flags);
382 #else /* _KERNEL */
383 struct cam_device;
384
385 char * cam_error_string(struct cam_device *device, union ccb *ccb, char *str,
386 int str_len, cam_error_string_flags flags,
387 cam_error_proto_flags proto_flags);
388 void cam_error_print(struct cam_device *device, union ccb *ccb,
389 cam_error_string_flags flags,
390 cam_error_proto_flags proto_flags, FILE *ofile);
391 #endif /* _KERNEL */
392 __END_DECLS
393
394 #ifdef _KERNEL
395 static __inline void cam_init_pinfo(cam_pinfo *pinfo);
396
397 static __inline void cam_init_pinfo(cam_pinfo *pinfo)
398 {
399 pinfo->priority = CAM_PRIORITY_NONE;
400 pinfo->index = CAM_UNQUEUED_INDEX;
401 }
402 #endif
403
404 #endif /* _CAM_CAM_H */
Cache object: 518e81e6475d36f48a248e28d8ee623d
|