FreeBSD/Linux Kernel Cross Reference
sys/conf/NOTES

     # $FreeBSD: releng/10.0/sys/conf/NOTES 256381 2013-10-12 15:31:36Z markm $
     #
     # NOTES -- Lines that can be cut/pasted into kernel and hints configs.
     #
     # Lines that begin with 'device', 'options', 'machine', 'ident', 'maxusers',
     # 'makeoptions', 'hints', etc. go into the kernel configuration that you
     # run config(8) with.
     #
     # Lines that begin with 'hint.' are NOT for config(8), they go into your
    # hints file.  See /boot/device.hints and/or the 'hints' config(8) directive.
    #
    # Please use ``make LINT'' to create an old-style LINT file if you want to
    # do kernel test-builds.
    #
    # This file contains machine independent kernel configuration notes.  For
    # machine dependent notes, look in /sys/<arch>/conf/NOTES.
    #
    
    #
    # NOTES conventions and style guide:
    #
    # Large block comments should begin and end with a line containing only a
    # comment character.
    #
    # To describe a particular object, a block comment (if it exists) should
    # come first.  Next should come device, options, and hints lines in that
    # order.  All device and option lines must be described by a comment that
    # doesn't just expand the device or option name.  Use only a concise
    # comment on the same line if possible.  Very detailed descriptions of
    # devices and subsystems belong in man pages.
    #
    # A space followed by a tab separates 'options' from an option name.  Two
    # spaces followed by a tab separate 'device' from a device name.  Comments
    # after an option or device should use one space after the comment character.
    # To comment out a negative option that disables code and thus should not be
    # enabled for LINT builds, precede 'options' with "#!".
    #
    
    #
    # This is the ``identification'' of the kernel.  Usually this should
    # be the same as the name of your kernel.
    #
    ident           LINT
    
    #
    # The `maxusers' parameter controls the static sizing of a number of
    # internal system tables by a formula defined in subr_param.c.
    # Omitting this parameter or setting it to 0 will cause the system to
    # auto-size based on physical memory.
    #
    maxusers        10
    
    # To statically compile in device wiring instead of /boot/device.hints
    #hints          "LINT.hints"            # Default places to look for devices.
    
    # Use the following to compile in values accessible to the kernel
    # through getenv() (or kenv(1) in userland). The format of the file
    # is 'variable=value', see kenv(1)
    #
    #env            "LINT.env"
    
    #
    # The `makeoptions' parameter allows variables to be passed to the
    # generated Makefile in the build area.
    #
    # CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
    # after most other flags.  Here we use it to inhibit use of non-optimal
    # gcc built-in functions (e.g., memcmp).
    #
    # DEBUG happens to be magic.
    # The following is equivalent to 'config -g KERNELNAME' and creates
    # 'kernel.debug' compiled with -g debugging as well as a normal
    # 'kernel'.  Use 'make install.debug' to install the debug kernel
    # but that isn't normally necessary as the debug symbols are not loaded
    # by the kernel and are not useful there anyway.
    #
    # KERNEL can be overridden so that you can change the default name of your
    # kernel.
    #
    # MODULES_OVERRIDE can be used to limit modules built to a specific list.
    #
    makeoptions     CONF_CFLAGS=-fno-builtin  #Don't allow use of memcmp, etc.
    #makeoptions    DEBUG=-g                #Build kernel with gdb(1) debug symbols
    #makeoptions    KERNEL=foo              #Build kernel "foo" and install "/foo"
    # Only build ext2fs module plus those parts of the sound system I need.
    #makeoptions    MODULES_OVERRIDE="ext2fs sound/sound sound/driver/maestro3"
    makeoptions     DESTDIR=/tmp
    
    #
    # FreeBSD processes are subject to certain limits to their consumption
    # of system resources.  See getrlimit(2) for more details.  Each
    # resource limit has two values, a "soft" limit and a "hard" limit.
    # The soft limits can be modified during normal system operation, but
    # the hard limits are set at boot time.  Their default values are
    # in sys/<arch>/include/vmparam.h.  There are two ways to change them:
    # 
    # 1.  Set the values at kernel build time.  The options below are one
    #     way to allow that limit to grow to 1GB.  They can be increased
    #     further by changing the parameters:
   #       
   # 2.  In /boot/loader.conf, set the tunables kern.maxswzone,
   #     kern.maxbcache, kern.maxtsiz, kern.dfldsiz, kern.maxdsiz,
   #     kern.dflssiz, kern.maxssiz and kern.sgrowsiz.
   #
   # The options in /boot/loader.conf override anything in the kernel
   # configuration file.  See the function init_param1 in
   # sys/kern/subr_param.c for more details.
   #
   
   options         MAXDSIZ=(1024UL*1024*1024)
   options         MAXSSIZ=(128UL*1024*1024)
   options         DFLDSIZ=(1024UL*1024*1024)
   
   #
   # BLKDEV_IOSIZE sets the default block size used in user block
   # device I/O.  Note that this value will be overridden by the label
   # when specifying a block device from a label with a non-0
   # partition blocksize.  The default is PAGE_SIZE.
   #
   options         BLKDEV_IOSIZE=8192
   
   #
   # MAXPHYS and DFLTPHYS
   #
   # These are the maximal and safe 'raw' I/O block device access sizes.
   # Reads and writes will be split into MAXPHYS chunks for known good
   # devices and DFLTPHYS for the rest. Some applications have better
   # performance with larger raw I/O access sizes. Note that certain VM
   # parameters are derived from these values and making them too large
   # can make an an unbootable kernel.
   #
   # The defaults are 64K and 128K respectively.
   options         DFLTPHYS=(64*1024)
   options         MAXPHYS=(128*1024)
   
   
   # This allows you to actually store this configuration file into
   # the kernel binary itself. See config(8) for more details.
   #
   options         INCLUDE_CONFIG_FILE     # Include this file in kernel
   
   #
   # Compile-time defaults for various boot parameters
   #
   options         BOOTVERBOSE=1
   options         BOOTHOWTO=RB_MULTIPLE
   
   options         GEOM_AES                # Don't use, use GEOM_BDE
   options         GEOM_BDE                # Disk encryption.
   options         GEOM_BSD                # BSD disklabels
   options         GEOM_CACHE              # Disk cache.
   options         GEOM_CONCAT             # Disk concatenation.
   options         GEOM_ELI                # Disk encryption.
   options         GEOM_FOX                # Redundant path mitigation
   options         GEOM_GATE               # Userland services.
   options         GEOM_JOURNAL            # Journaling.
   options         GEOM_LABEL              # Providers labelization.
   options         GEOM_LINUX_LVM          # Linux LVM2 volumes
   options         GEOM_MBR                # DOS/MBR partitioning
   options         GEOM_MIRROR             # Disk mirroring.
   options         GEOM_MULTIPATH          # Disk multipath
   options         GEOM_NOP                # Test class.
   options         GEOM_PART_APM           # Apple partitioning
   options         GEOM_PART_BSD           # BSD disklabel
   options         GEOM_PART_EBR           # Extended Boot Records
   options         GEOM_PART_EBR_COMPAT    # Backward compatible partition names
   options         GEOM_PART_GPT           # GPT partitioning
   options         GEOM_PART_LDM           # Logical Disk Manager
   options         GEOM_PART_MBR           # MBR partitioning
   options         GEOM_PART_PC98          # PC-9800 disk partitioning
   options         GEOM_PART_VTOC8         # SMI VTOC8 disk label
   options         GEOM_PC98               # NEC PC9800 partitioning
   options         GEOM_RAID               # Soft RAID functionality.
   options         GEOM_RAID3              # RAID3 functionality.
   options         GEOM_SHSEC              # Shared secret.
   options         GEOM_STRIPE             # Disk striping.
   options         GEOM_SUNLABEL           # Sun/Solaris partitioning
   options         GEOM_UZIP               # Read-only compressed disks
   options         GEOM_VIRSTOR            # Virtual storage.
   options         GEOM_VOL                # Volume names from UFS superblock
   options         GEOM_ZERO               # Performance testing helper.
   
   #
   # The root device and filesystem type can be compiled in;
   # this provides a fallback option if the root device cannot
   # be correctly guessed by the bootstrap code, or an override if
   # the RB_DFLTROOT flag (-r) is specified when booting the kernel.
   #
   options         ROOTDEVNAME=\"ufs:da0s2e\"
   
   
   #####################################################################
   # Scheduler options:
   #
   # Specifying one of SCHED_4BSD or SCHED_ULE is mandatory.  These options
   # select which scheduler is compiled in.
   #
   # SCHED_4BSD is the historical, proven, BSD scheduler.  It has a global run
   # queue and no CPU affinity which makes it suboptimal for SMP.  It has very
   # good interactivity and priority selection.
   #
   # SCHED_ULE provides significant performance advantages over 4BSD on many
   # workloads on SMP machines.  It supports cpu-affinity, per-cpu runqueues
   # and scheduler locks.  It also has a stronger notion of interactivity 
   # which leads to better responsiveness even on uniprocessor machines.  This
   # is the default scheduler.
   #
   # SCHED_STATS is a debugging option which keeps some stats in the sysctl
   # tree at 'kern.sched.stats' and is useful for debugging scheduling decisions.
   #
   options         SCHED_4BSD
   options         SCHED_STATS
   #options        SCHED_ULE
   
   #####################################################################
   # SMP OPTIONS:
   #
   # SMP enables building of a Symmetric MultiProcessor Kernel.
   
   # Mandatory:
   options         SMP                     # Symmetric MultiProcessor Kernel
   
   # MAXCPU defines the maximum number of CPUs that can boot in the system.
   # A default value should be already present, for every architecture.
   options         MAXCPU=32
   
   # MAXMEMDOM defines the maximum number of memory domains that can boot in the
   # system.  A default value should already be defined by every architecture.
   options         MAXMEMDOM=1
   
   # ADAPTIVE_MUTEXES changes the behavior of blocking mutexes to spin
   # if the thread that currently owns the mutex is executing on another
   # CPU.  This behavior is enabled by default, so this option can be used
   # to disable it.
   options         NO_ADAPTIVE_MUTEXES
   
   # ADAPTIVE_RWLOCKS changes the behavior of reader/writer locks to spin
   # if the thread that currently owns the rwlock is executing on another
   # CPU.  This behavior is enabled by default, so this option can be used
   # to disable it.
   options         NO_ADAPTIVE_RWLOCKS
   
   # ADAPTIVE_SX changes the behavior of sx locks to spin if the thread that
   # currently owns the sx lock is executing on another CPU.
   # This behavior is enabled by default, so this option can be used to
   # disable it.
   options         NO_ADAPTIVE_SX
   
   # MUTEX_NOINLINE forces mutex operations to call functions to perform each
   # operation rather than inlining the simple cases.  This can be used to
   # shrink the size of the kernel text segment.  Note that this behavior is
   # already implied by the INVARIANT_SUPPORT, INVARIANTS, KTR, LOCK_PROFILING,
   # and WITNESS options.
   options         MUTEX_NOINLINE
   
   # RWLOCK_NOINLINE forces rwlock operations to call functions to perform each
   # operation rather than inlining the simple cases.  This can be used to
   # shrink the size of the kernel text segment.  Note that this behavior is
   # already implied by the INVARIANT_SUPPORT, INVARIANTS, KTR, LOCK_PROFILING,
   # and WITNESS options.
   options         RWLOCK_NOINLINE
   
   # SX_NOINLINE forces sx lock operations to call functions to perform each
   # operation rather than inlining the simple cases.  This can be used to
   # shrink the size of the kernel text segment.  Note that this behavior is
   # already implied by the INVARIANT_SUPPORT, INVARIANTS, KTR, LOCK_PROFILING,
   # and WITNESS options.
   options         SX_NOINLINE
   
   # SMP Debugging Options:
   #
   # CALLOUT_PROFILING enables rudimentary profiling of the callwheel data
   #         structure used as backend in callout(9).
   # PREEMPTION allows the threads that are in the kernel to be preempted by
   #         higher priority [interrupt] threads.  It helps with interactivity
   #         and allows interrupt threads to run sooner rather than waiting.
   #         WARNING! Only tested on amd64 and i386.
   # FULL_PREEMPTION instructs the kernel to preempt non-realtime kernel
   #         threads.  Its sole use is to expose race conditions and other
   #         bugs during development.  Enabling this option will reduce
   #         performance and increase the frequency of kernel panics by
   #         design.  If you aren't sure that you need it then you don't.
   #         Relies on the PREEMPTION option.  DON'T TURN THIS ON.
   # MUTEX_DEBUG enables various extra assertions in the mutex code.
   # SLEEPQUEUE_PROFILING enables rudimentary profiling of the hash table
   #         used to hold active sleep queues as well as sleep wait message
   #         frequency.
   # TURNSTILE_PROFILING enables rudimentary profiling of the hash table
   #         used to hold active lock queues.
   # UMTX_PROFILING enables rudimentary profiling of the hash table used 
             to hold active lock queues.
   # WITNESS enables the witness code which detects deadlocks and cycles
   #         during locking operations.
   # WITNESS_KDB causes the witness code to drop into the kernel debugger if
   #         a lock hierarchy violation occurs or if locks are held when going to
   #         sleep.
   # WITNESS_SKIPSPIN disables the witness checks on spin mutexes.
   options         PREEMPTION
   options         FULL_PREEMPTION
   options         MUTEX_DEBUG
   options         WITNESS
   options         WITNESS_KDB
   options         WITNESS_SKIPSPIN
   
   # LOCK_PROFILING - Profiling locks.  See LOCK_PROFILING(9) for details.
   options         LOCK_PROFILING
   # Set the number of buffers and the hash size.  The hash size MUST be larger
   # than the number of buffers.  Hash size should be prime.
   options         MPROF_BUFFERS="1536"
   options         MPROF_HASH_SIZE="1543"
   
   # Profiling for the callout(9) backend.
   options         CALLOUT_PROFILING
   
   # Profiling for internal hash tables.
   options         SLEEPQUEUE_PROFILING
   options         TURNSTILE_PROFILING
   options         UMTX_PROFILING
   
   
   #####################################################################
   # COMPATIBILITY OPTIONS
   
   #
   # Implement system calls compatible with 4.3BSD and older versions of
   # FreeBSD.  You probably do NOT want to remove this as much current code
   # still relies on the 4.3 emulation.  Note that some architectures that
   # are supported by FreeBSD do not include support for certain important
   # aspects of this compatibility option, namely those related to the
   # signal delivery mechanism.
   #
   options         COMPAT_43
   
   # Old tty interface.
   options         COMPAT_43TTY
   
   # Note that as a general rule, COMPAT_FREEBSD<n> depends on
   # COMPAT_FREEBSD<n+1>, COMPAT_FREEBSD<n+2>, etc.
   
   # Enable FreeBSD4 compatibility syscalls
   options         COMPAT_FREEBSD4
   
   # Enable FreeBSD5 compatibility syscalls
   options         COMPAT_FREEBSD5
   
   # Enable FreeBSD6 compatibility syscalls
   options         COMPAT_FREEBSD6
   
   # Enable FreeBSD7 compatibility syscalls
   options         COMPAT_FREEBSD7
   
   #
   # These three options provide support for System V Interface
   # Definition-style interprocess communication, in the form of shared
   # memory, semaphores, and message queues, respectively.
   #
   options         SYSVSHM
   options         SYSVSEM
   options         SYSVMSG
   
   
   #####################################################################
   # DEBUGGING OPTIONS
   
   #
   # Compile with kernel debugger related code.
   #
   options         KDB
   
   #
   # Print a stack trace of the current thread on the console for a panic.
   #
   options         KDB_TRACE
   
   #
   # Don't enter the debugger for a panic. Intended for unattended operation
   # where you may want to enter the debugger from the console, but still want
   # the machine to recover from a panic.
   #
   options         KDB_UNATTENDED
   
   #
   # Enable the ddb debugger backend.
   #
   options         DDB
   
   #
   # Print the numerical value of symbols in addition to the symbolic
   # representation.
   #
   options         DDB_NUMSYM
   
   #
   # Enable the remote gdb debugger backend.
   #
   options         GDB
   
   #
   # SYSCTL_DEBUG enables a 'sysctl' debug tree that can be used to dump the
   # contents of the registered sysctl nodes on the console.  It is disabled by
   # default because it generates excessively verbose console output that can
   # interfere with serial console operation.
   #
   options         SYSCTL_DEBUG
   
   #
   # Enable textdump by default, this disables kernel core dumps.
   #
   options         TEXTDUMP_PREFERRED
   
   #
   # Enable extra debug messages while performing textdumps.
   #
   options         TEXTDUMP_VERBOSE
   
   #
   # NO_SYSCTL_DESCR omits the sysctl node descriptions to save space in the
   # resulting kernel.
   options         NO_SYSCTL_DESCR
   
   #
   # MALLOC_DEBUG_MAXZONES enables multiple uma zones for malloc(9)
   # allocations that are smaller than a page.  The purpose is to isolate
   # different malloc types into hash classes, so that any buffer
   # overruns or use-after-free will usually only affect memory from
   # malloc types in that hash class.  This is purely a debugging tool;
   # by varying the hash function and tracking which hash class was
   # corrupted, the intersection of the hash classes from each instance
   # will point to a single malloc type that is being misused.  At this
   # point inspection or memguard(9) can be used to catch the offending
   # code.
   #
   options         MALLOC_DEBUG_MAXZONES=8
   
   #
   # DEBUG_MEMGUARD builds and enables memguard(9), a replacement allocator
   # for the kernel used to detect modify-after-free scenarios.  See the
   # memguard(9) man page for more information on usage.
   #
   options         DEBUG_MEMGUARD
   
   #
   # DEBUG_REDZONE enables buffer underflows and buffer overflows detection for
   # malloc(9).
   #
   options         DEBUG_REDZONE
   
   #
   # KTRACE enables the system-call tracing facility ktrace(2).  To be more
   # SMP-friendly, KTRACE uses a worker thread to process most trace events
   # asynchronously to the thread generating the event.  This requires a
   # pre-allocated store of objects representing trace events.  The
   # KTRACE_REQUEST_POOL option specifies the initial size of this store.
   # The size of the pool can be adjusted both at boottime and runtime via
   # the kern.ktrace_request_pool tunable and sysctl.
   #
   options         KTRACE                  #kernel tracing
   options         KTRACE_REQUEST_POOL=101
   
   #
   # KTR is a kernel tracing facility imported from BSD/OS.  It is
   # enabled with the KTR option.  KTR_ENTRIES defines the number of
   # entries in the circular trace buffer; it may be an arbitrary number.
   # KTR_BOOT_ENTRIES defines the number of entries during the early boot,
   # before malloc(9) is functional.
   # KTR_COMPILE defines the mask of events to compile into the kernel as
   # defined by the KTR_* constants in <sys/ktr.h>.  KTR_MASK defines the
   # initial value of the ktr_mask variable which determines at runtime
   # what events to trace.  KTR_CPUMASK determines which CPU's log
   # events, with bit X corresponding to CPU X.  The layout of the string
   # passed as KTR_CPUMASK must match a series of bitmasks each of them
   # separated by the "," character (ie:
   # KTR_CPUMASK=0xAF,0xFFFFFFFFFFFFFFFF).  KTR_VERBOSE enables
   # dumping of KTR events to the console by default.  This functionality
   # can be toggled via the debug.ktr_verbose sysctl and defaults to off
   # if KTR_VERBOSE is not defined.  See ktr(4) and ktrdump(8) for details.
   #
   options         KTR
   options         KTR_BOOT_ENTRIES=1024
   options         KTR_ENTRIES=(128*1024)
   options         KTR_COMPILE=(KTR_INTR|KTR_PROC)
   options         KTR_MASK=KTR_INTR
   options         KTR_CPUMASK=0x3
   options         KTR_VERBOSE
   
   #
   # ALQ(9) is a facility for the asynchronous queuing of records from the kernel
   # to a vnode, and is employed by services such as ktr(4) to produce trace
   # files based on a kernel event stream.  Records are written asynchronously
   # in a worker thread.
   #
   options         ALQ
   options         KTR_ALQ
   
   #
   # The INVARIANTS option is used in a number of source files to enable
   # extra sanity checking of internal structures.  This support is not
   # enabled by default because of the extra time it would take to check
   # for these conditions, which can only occur as a result of
   # programming errors.
   #
   options         INVARIANTS
   
   #
   # The INVARIANT_SUPPORT option makes us compile in support for
   # verifying some of the internal structures.  It is a prerequisite for
   # 'INVARIANTS', as enabling 'INVARIANTS' will make these functions be
   # called.  The intent is that you can set 'INVARIANTS' for single
   # source files (by changing the source file or specifying it on the
   # command line) if you have 'INVARIANT_SUPPORT' enabled.  Also, if you
   # wish to build a kernel module with 'INVARIANTS', then adding
   # 'INVARIANT_SUPPORT' to your kernel will provide all the necessary
   # infrastructure without the added overhead.
   #
   options         INVARIANT_SUPPORT
   
   #
   # The DIAGNOSTIC option is used to enable extra debugging information
   # from some parts of the kernel.  As this makes everything more noisy,
   # it is disabled by default.
   #
   options         DIAGNOSTIC
   
   #
   # REGRESSION causes optional kernel interfaces necessary only for regression
   # testing to be enabled.  These interfaces may constitute security risks
   # when enabled, as they permit processes to easily modify aspects of the
   # run-time environment to reproduce unlikely or unusual (possibly normally
   # impossible) scenarios.
   #
   options         REGRESSION
   
   #
   # This option lets some drivers co-exist that can't co-exist in a running
   # system.  This is used to be able to compile all kernel code in one go for
   # quality assurance purposes (like this file, which the option takes it name
   # from.)
   #
   options         COMPILING_LINT
   
   #
   # STACK enables the stack(9) facility, allowing the capture of kernel stack
   # for the purpose of procinfo(1), etc.  stack(9) will also be compiled in
   # automatically if DDB(4) is compiled into the kernel.
   #
   options         STACK
   
   
   #####################################################################
   # PERFORMANCE MONITORING OPTIONS
   
   #
   # The hwpmc driver that allows the use of in-CPU performance monitoring
   # counters for performance monitoring.  The base kernel needs to be configured
   # with the 'options' line, while the hwpmc device can be either compiled
   # in or loaded as a loadable kernel module.
   #
   # Additional configuration options may be required on specific architectures,
   # please see hwpmc(4).
   
   device          hwpmc                   # Driver (also a loadable module)
   options         HWPMC_HOOKS             # Other necessary kernel hooks
   
   
   #####################################################################
   # NETWORKING OPTIONS
   
   #
   # Protocol families
   #
   options         INET                    #Internet communications protocols
   options         INET6                   #IPv6 communications protocols
   
   options         ROUTETABLES=2           # allocated fibs up to 65536. default is 1.
                                           # but that would be a bad idea as they are large.
   
   options         TCP_OFFLOAD             # TCP offload support.
   
   # In order to enable IPSEC you MUST also add device crypto to 
   # your kernel configuration
   options         IPSEC                   #IP security (requires device crypto)
   #options        IPSEC_DEBUG             #debug for IP security
   #
   # #DEPRECATED#
   # Set IPSEC_FILTERTUNNEL to change the default of the sysctl to force packets
   # coming through a tunnel to be processed by any configured packet filtering
   # twice. The default is that packets coming out of a tunnel are _not_ processed;
   # they are assumed trusted.
   #
   # IPSEC history is preserved for such packets, and can be filtered
   # using ipfw(8)'s 'ipsec' keyword, when this option is enabled.
   #
   #options        IPSEC_FILTERTUNNEL      #filter ipsec packets from a tunnel
   #
   # Set IPSEC_NAT_T to enable NAT-Traversal support.  This enables
   # optional UDP encapsulation of ESP packets.
   #
   options         IPSEC_NAT_T             #NAT-T support, UDP encap of ESP
   
   options         IPX                     #IPX/SPX communications protocols
   
   options         NETATALK                #Appletalk communications protocols
   options         NETATALKDEBUG           #Appletalk debugging
   
   #
   # SMB/CIFS requester
   # NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
   # options.
   options         NETSMB                  #SMB/CIFS requester
   
   # mchain library. It can be either loaded as KLD or compiled into kernel
   options         LIBMCHAIN
   
   # libalias library, performing NAT
   options         LIBALIAS
   
   # flowtable cache
   options         FLOWTABLE
   
   #
   # SCTP is a NEW transport protocol defined by
   # RFC2960 updated by RFC3309 and RFC3758.. and
   # soon to have a new base RFC and many many more
   # extensions. This release supports all the extensions
   # including many drafts (most about to become RFC's).
   # It is the reference implementation of SCTP
   # and is quite well tested.
   #
   # Note YOU MUST have both INET and INET6 defined.
   # You don't have to enable V6, but SCTP is 
   # dual stacked and so far we have not torn apart
   # the V6 and V4.. since an association can span
   # both a V6 and V4 address at the SAME time :-)
   #
   options         SCTP
   # There are bunches of options:
   # this one turns on all sorts of
   # nastily printing that you can
   # do. It's all controlled by a
   # bit mask (settable by socket opt and
   # by sysctl). Including will not cause
   # logging until you set the bits.. but it
   # can be quite verbose.. so without this
   # option we don't do any of the tests for
   # bits and prints.. which makes the code run
   # faster.. if you are not debugging don't use.
   options         SCTP_DEBUG
   #
   # This option turns off the CRC32c checksum. Basically,
   # you will not be able to talk to anyone else who
   # has not done this. Its more for experimentation to
   # see how much CPU the CRC32c really takes. Most new
   # cards for TCP support checksum offload.. so this 
   # option gives you a "view" into what SCTP would be
   # like with such an offload (which only exists in
   # high in iSCSI boards so far). With the new
   # splitting 8's algorithm its not as bad as it used
   # to be.. but it does speed things up try only
   # for in a captured lab environment :-)
   options         SCTP_WITH_NO_CSUM
   #
   
   #
   # All that options after that turn on specific types of
   # logging. You can monitor CWND growth, flight size
   # and all sorts of things. Go look at the code and
   # see. I have used this to produce interesting 
   # charts and graphs as well :->
   # 
   # I have not yet committed the tools to get and print
   # the logs, I will do that eventually .. before then
   # if you want them send me an email rrs@freebsd.org
   # You basically must have ktr(4) enabled for these
   # and you then set the sysctl to turn on/off various
   # logging bits. Use ktrdump(8) to pull the log and run
   # it through a display program.. and graphs and other
   # things too.
   #
   options         SCTP_LOCK_LOGGING
   options         SCTP_MBUF_LOGGING
   options         SCTP_MBCNT_LOGGING
   options         SCTP_PACKET_LOGGING
   options         SCTP_LTRACE_CHUNKS
   options         SCTP_LTRACE_ERRORS
   
   
   # altq(9). Enable the base part of the hooks with the ALTQ option.
   # Individual disciplines must be built into the base system and can not be
   # loaded as modules at this point. ALTQ requires a stable TSC so if yours is
   # broken or changes with CPU throttling then you must also have the ALTQ_NOPCC
   # option.
   options         ALTQ
   options         ALTQ_CBQ        # Class Based Queueing
   options         ALTQ_RED        # Random Early Detection
   options         ALTQ_RIO        # RED In/Out
   options         ALTQ_HFSC       # Hierarchical Packet Scheduler
   options         ALTQ_CDNR       # Traffic conditioner
   options         ALTQ_PRIQ       # Priority Queueing
   options         ALTQ_NOPCC      # Required if the TSC is unusable
   options         ALTQ_DEBUG
   
   # netgraph(4). Enable the base netgraph code with the NETGRAPH option.
   # Individual node types can be enabled with the corresponding option
   # listed below; however, this is not strictly necessary as netgraph
   # will automatically load the corresponding KLD module if the node type
   # is not already compiled into the kernel. Each type below has a
   # corresponding man page, e.g., ng_async(8).
   options         NETGRAPH                # netgraph(4) system
   options         NETGRAPH_DEBUG          # enable extra debugging, this
                                           # affects netgraph(4) and nodes
   # Node types
   options         NETGRAPH_ASYNC
   options         NETGRAPH_ATMLLC
   options         NETGRAPH_ATM_ATMPIF
   options         NETGRAPH_BLUETOOTH              # ng_bluetooth(4)
   options         NETGRAPH_BLUETOOTH_BT3C         # ng_bt3c(4)
   options         NETGRAPH_BLUETOOTH_HCI          # ng_hci(4)
   options         NETGRAPH_BLUETOOTH_L2CAP        # ng_l2cap(4)
   options         NETGRAPH_BLUETOOTH_SOCKET       # ng_btsocket(4)
   options         NETGRAPH_BLUETOOTH_UBT          # ng_ubt(4)
   options         NETGRAPH_BLUETOOTH_UBTBCMFW     # ubtbcmfw(4)
   options         NETGRAPH_BPF
   options         NETGRAPH_BRIDGE
   options         NETGRAPH_CAR
   options         NETGRAPH_CISCO
   options         NETGRAPH_DEFLATE
   options         NETGRAPH_DEVICE
   options         NETGRAPH_ECHO
   options         NETGRAPH_EIFACE
   options         NETGRAPH_ETHER
   options         NETGRAPH_FEC
   options         NETGRAPH_FRAME_RELAY
   options         NETGRAPH_GIF
   options         NETGRAPH_GIF_DEMUX
   options         NETGRAPH_HOLE
   options         NETGRAPH_IFACE
   options         NETGRAPH_IP_INPUT
   options         NETGRAPH_IPFW
   options         NETGRAPH_KSOCKET
   options         NETGRAPH_L2TP
   options         NETGRAPH_LMI
   # MPPC compression requires proprietary files (not included)
   #options        NETGRAPH_MPPC_COMPRESSION
   options         NETGRAPH_MPPC_ENCRYPTION
   options         NETGRAPH_NETFLOW
   options         NETGRAPH_NAT
   options         NETGRAPH_ONE2MANY
   options         NETGRAPH_PATCH
   options         NETGRAPH_PIPE
   options         NETGRAPH_PPP
   options         NETGRAPH_PPPOE
   options         NETGRAPH_PPTPGRE
   options         NETGRAPH_PRED1
   options         NETGRAPH_RFC1490
   options         NETGRAPH_SOCKET
   options         NETGRAPH_SPLIT
   options         NETGRAPH_SPPP
   options         NETGRAPH_TAG
   options         NETGRAPH_TCPMSS
   options         NETGRAPH_TEE
   options         NETGRAPH_UI
   options         NETGRAPH_VJC
   options         NETGRAPH_VLAN
   
   # NgATM - Netgraph ATM
   options         NGATM_ATM
   options         NGATM_ATMBASE
   options         NGATM_SSCOP
   options         NGATM_SSCFU
   options         NGATM_UNI
   options         NGATM_CCATM
   
   device          mn      # Munich32x/Falc54 Nx64kbit/sec cards.
   
   # Network stack virtualization.
   #options        VIMAGE
   #options        VNET_DEBUG      # debug for VIMAGE
   
   #
   # Network interfaces:
   #  The `loop' device is MANDATORY when networking is enabled.
   device          loop
   
   #  The `ether' device provides generic code to handle
   #  Ethernets; it is MANDATORY when an Ethernet device driver is
   #  configured or token-ring is enabled.
   device          ether
   
   #  The `vlan' device implements the VLAN tagging of Ethernet frames
   #  according to IEEE 802.1Q.
   device          vlan
   
   #  The `wlan' device provides generic code to support 802.11
   #  drivers, including host AP mode; it is MANDATORY for the wi,
   #  and ath drivers and will eventually be required by all 802.11 drivers.
   device          wlan
   options         IEEE80211_DEBUG         #enable debugging msgs
   options         IEEE80211_AMPDU_AGE     #age frames in AMPDU reorder q's
   options         IEEE80211_SUPPORT_MESH  #enable 802.11s D3.0 support
   options         IEEE80211_SUPPORT_TDMA  #enable TDMA support
   
   #  The `wlan_wep', `wlan_tkip', and `wlan_ccmp' devices provide
   #  support for WEP, TKIP, and AES-CCMP crypto protocols optionally
   #  used with 802.11 devices that depend on the `wlan' module.
   device          wlan_wep
   device          wlan_ccmp
   device          wlan_tkip
   
   #  The `wlan_xauth' device provides support for external (i.e. user-mode)
   #  authenticators for use with 802.11 drivers that use the `wlan'
   #  module and support 802.1x and/or WPA security protocols.
   device          wlan_xauth
   
   #  The `wlan_acl' device provides a MAC-based access control mechanism
   #  for use with 802.11 drivers operating in ap mode and using the
   #  `wlan' module.
   #  The 'wlan_amrr' device provides AMRR transmit rate control algorithm
   device          wlan_acl
   device          wlan_amrr
   
   # Generic TokenRing
   device          token
   
   #  The `fddi' device provides generic code to support FDDI.
   device          fddi
   
   #  The `arcnet' device provides generic code to support Arcnet.
   device          arcnet
   
   #  The `sppp' device serves a similar role for certain types
   #  of synchronous PPP links (like `cx', `ar').
   device          sppp
   
   #  The `bpf' device enables the Berkeley Packet Filter.  Be
   #  aware of the legal and administrative consequences of enabling this
   #  option.  DHCP requires bpf.
   device          bpf
   
   #  The `netmap' device implements memory-mapped access to network
   #  devices from userspace, enabling wire-speed packet capture and
   #  generation even at 10Gbit/s. Requires support in the device
   #  driver. Supported drivers are ixgbe, e1000, re.
   device          netmap
   
   #  The `disc' device implements a minimal network interface,
   #  which throws away all packets sent and never receives any.  It is
   #  included for testing and benchmarking purposes.
   device          disc
   
   # The `epair' device implements a virtual back-to-back connected Ethernet
   # like interface pair.
   device          epair
   
   #  The `edsc' device implements a minimal Ethernet interface,
   #  which discards all packets sent and receives none.
   device          edsc
   
   #  The `tap' device is a pty-like virtual Ethernet interface
   device          tap
   
   #  The `tun' device implements (user-)ppp and nos-tun(8)
   device          tun
   
   #  The `gif' device implements IPv6 over IP4 tunneling,
   #  IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
   #  IPv6 over IPv6 tunneling.
   #  The `gre' device implements two types of IP4 over IP4 tunneling:
   #  GRE and MOBILE, as specified in the RFC1701 and RFC2004.
   #  The XBONEHACK option allows the same pair of addresses to be configured on
   #  multiple gif interfaces.
   device          gif
   device          gre
   options         XBONEHACK
   
   #  The `faith' device captures packets sent to it and diverts them
   #  to the IPv4/IPv6 translation daemon.
   #  The `stf' device implements 6to4 encapsulation.
   device          faith
   device          stf
   
   #  The `ef' device provides support for multiple ethernet frame types
   #  specified via ETHER_* options. See ef(4) for details.
   device          ef
   options         ETHER_II                # enable Ethernet_II frame
   options         ETHER_8023              # enable Ethernet_802.3 (Novell) frame
   options         ETHER_8022              # enable Ethernet_802.2 frame
   options         ETHER_SNAP              # enable Ethernet_802.2/SNAP frame
   
   # The pf packet filter consists of three devices:
   #  The `pf' device provides /dev/pf and the firewall code itself.
   #  The `pflog' device provides the pflog0 interface which logs packets.
   #  The `pfsync' device provides the pfsync0 interface used for
   #   synchronization of firewall state tables (over the net).
   device          pf
   device          pflog
   device          pfsync
   
   # Bridge interface.
   device          if_bridge
   
   # Common Address Redundancy Protocol. See carp(4) for more details.
   device          carp
   
   # IPsec interface.
   device          enc
   
   # Link aggregation interface.
   device          lagg
   
   #
   # Internet family options:
   #
   # MROUTING enables the kernel multicast packet forwarder, which works
   # with mrouted and XORP.
   #
   # IPFIREWALL enables support for IP firewall construction, in
   # conjunction with the `ipfw' program.  IPFIREWALL_VERBOSE sends
   # logged packets to the system logger.  IPFIREWALL_VERBOSE_LIMIT
   # limits the number of times a matching entry can be logged.
   #
   # WARNING:  IPFIREWALL defaults to a policy of "deny ip from any to any"
   # and if you do not add other rules during startup to allow access,
   # YOU WILL LOCK YOURSELF OUT.  It is suggested that you set firewall_type=open
   # in /etc/rc.conf when first enabling this feature, then refining the
   # firewall rules in /etc/rc.firewall after you've tested that the new kernel
   # feature works properly.
   #
   # IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
   # allow everything.  Use with care, if a cracker can crash your
   # firewall machine, they can get to your protected machines.  However,
   # if you are using it as an as-needed filter for specific problems as
   # they arise, then this may be for you.  Changing the default to 'allow'
   # means that you won't get stuck if the kernel and /sbin/ipfw binary get
   # out of sync.
   #
   # IPDIVERT enables the divert IP sockets, used by ``ipfw divert''.  It
   # depends on IPFIREWALL if compiled into the kernel.
   #
   # IPFIREWALL_NAT adds support for in kernel nat in ipfw, and it requires
   # LIBALIAS.
   #
   # IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
   # packets without touching the TTL).  This can be useful to hide firewalls
   # from traceroute and similar tools.
   #
   # PF_DEFAULT_TO_DROP causes the default pf(4) rule to deny everything.
   #
   # TCPDEBUG enables code which keeps traces of the TCP state machine
   # for sockets with the SO_DEBUG option set, which can then be examined
   # using the trpt(8) utility.
   #
   # RADIX_MPATH provides support for equal-cost multi-path routing.
   #
   options         MROUTING                # Multicast routing
   options         IPFIREWALL              #firewall
   options         IPFIREWALL_VERBOSE      #enable logging to syslogd(8)
   options         IPFIREWALL_VERBOSE_LIMIT=100    #limit verbosity
   options         IPFIREWALL_DEFAULT_TO_ACCEPT    #allow everything by default
   options         IPFIREWALL_NAT          #ipfw kernel nat support
   options         IPDIVERT                #divert sockets
   options         IPFILTER                #ipfilter support
   options         IPFILTER_LOG            #ipfilter logging
   options         IPFILTER_LOOKUP         #ipfilter pools
   options         IPFILTER_DEFAULT_BLOCK  #block all packets by default
   options         IPSTEALTH               #support for stealth forwarding
   options         PF_DEFAULT_TO_DROP      #drop everything by default
   options         TCPDEBUG
   options         RADIX_MPATH
   
   # The MBUF_STRESS_TEST option enables options which create
   # various random failures / extreme cases related to mbuf
   # functions.  See mbuf(9) for a list of available test cases.
   # MBUF_PROFILING enables code to profile the mbuf chains
   # exiting the system (via participating interfaces) and
   # return a logarithmic histogram of monitored parameters
   # (e.g. packet size, wasted space, number of mbufs in chain).
   options         MBUF_STRESS_TEST
   options         MBUF_PROFILING
   
   # Statically link in accept filters
   options         ACCEPT_FILTER_DATA
   options         ACCEPT_FILTER_DNS
   options         ACCEPT_FILTER_HTTP
   
   # TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are
   # carried in TCP option 19. This option is commonly used to protect
   # TCP sessions (e.g. BGP) where IPSEC is not available nor desirable.
   # This is enabled on a per-socket basis using the TCP_MD5SIG socket option.
   # This requires the use of 'device crypto', 'options IPSEC'
   # or 'device cryptodev'.
   options         TCP_SIGNATURE           #include support for RFC 2385
   
   # DUMMYNET enables the "dummynet" bandwidth limiter.  You need IPFIREWALL
   # as well.  See dummynet(4) and ipfw(8) for more info.  When you run
   # DUMMYNET it is advisable to also have at least "options HZ=1000" to achieve
   # a smooth scheduling of the traffic.
   options         DUMMYNET
   
   #####################################################################
  # FILESYSTEM OPTIONS
  
  #
  # Only the root filesystem needs to be statically compiled or preloaded
  # as module; everything else will be automatically loaded at mount
  # time.  Some people still prefer to statically compile other
  # filesystems as well.
  #
  # NB: The UNION filesystem was known to be buggy in the past.  It is now
  # being actively maintained, although there are still some issues being
  # resolved.
  #
  
  # One of these is mandatory:
  options         FFS                     #Fast filesystem
  options         NFSCLIENT               #Network File System client
  
  # The rest are optional:
  options         CD9660                  #ISO 9660 filesystem
  options         FDESCFS                 #File descriptor filesystem
  options         FUSE                    #FUSE support module
  options         MSDOSFS                 #MS DOS File System (FAT, FAT32)
  options         NFSSERVER               #Network File System server
  options         NFSLOCKD                #Network Lock Manager
  options         NFSCL                   #New Network Filesystem Client
  options         NFSD                    #New Network Filesystem Server
  options         KGSSAPI                 #Kernel GSSAPI implementation
  
  options         NULLFS                  #NULL filesystem
  options         PROCFS                  #Process filesystem (requires PSEUDOFS)
  options         PSEUDOFS                #Pseudo-filesystem framework
  options         PSEUDOFS_TRACE          #Debugging support for PSEUDOFS
  options         SMBFS                   #SMB/CIFS filesystem
  options         TMPFS                   #Efficient memory filesystem
  options         UDF                     #Universal Disk Format
  options         UNIONFS                 #Union filesystem
  # The xFS_ROOT options REQUIRE the associated ``options xFS''
  options         NFS_ROOT                #NFS usable as root device
  
  # Soft updates is a technique for improving filesystem speed and
  # making abrupt shutdown less risky.
  #
  options         SOFTUPDATES
  
  # Extended attributes allow additional data to be associated with files,
  # and is used for ACLs, Capabilities, and MAC labels.
  # See src/sys/ufs/ufs/README.extattr for more information.
  options         UFS_EXTATTR
  options         UFS_EXTATTR_AUTOSTART
  
  # Access Control List support for UFS filesystems.  The current ACL
  # implementation requires extended attribute support, UFS_EXTATTR,
  # for the underlying filesystem.
  # See src/sys/ufs/ufs/README.acls for more information.
  options         UFS_ACL
  
  # Directory hashing improves the speed of operations on very large
  # directories at the expense of some memory.
  options         UFS_DIRHASH
  
  # Gjournal-based UFS journaling support.
  options         UFS_GJOURNAL
  
  # Make space in the kernel for a root filesystem on a md device.
  # Define to the number of kilobytes to reserve for the filesystem.
  options         MD_ROOT_SIZE=10
  
  # Make the md device a potential root device, either with preloaded
  # images of type mfs_root or md_root.
  options         MD_ROOT
  
  # Disk quotas are supported when this option is enabled.
  options         QUOTA                   #enable disk quotas
  
  # If you are running a machine just as a fileserver for PC and MAC
  # users, using SAMBA or Netatalk, you may consider setting this option
  # and keeping all those users' directories on a filesystem that is
  # mounted with the suiddir option. This gives new files the same
  # ownership as the directory (similar to group). It's a security hole
  # if you let these users run programs, so confine it to file-servers
  # (but it'll save you lots of headaches in those cases). Root owned
  # directories are exempt and X bits are cleared. The suid bit must be
  # set on the directory as well; see chmod(1). PC owners can't see/set
  # ownerships so they keep getting their toes trodden on. This saves
  # you all the support calls as the filesystem it's used on will act as
  # they expect: "It's my dir so it must be my file".
  #
  options         SUIDDIR
  
  # NFS options:
  options         NFS_MINATTRTIMO=3       # VREG attrib cache timeout in sec
  options         NFS_MAXATTRTIMO=60
  options         NFS_MINDIRATTRTIMO=30   # VDIR attrib cache timeout in sec
  options         NFS_MAXDIRATTRTIMO=60
  options         NFS_GATHERDELAY=10      # Default write gather delay (msec)
  options         NFS_WDELAYHASHSIZ=16    # and with this
  options         NFS_DEBUG               # Enable NFS Debugging
  
  #
  # Add support for the EXT2FS filesystem of Linux fame.  Be a bit
  # careful with this - the ext2fs code has a tendency to lag behind
  # changes and not be exercised very much, so mounting read/write could
  # be dangerous (and even mounting read only could result in panics.)
  #
  options         EXT2FS
  
  #
  # Add support for the ReiserFS filesystem (used in Linux). Currently,
  # this is limited to read-only access.
  #
  options         REISERFS
  
  # Use real implementations of the aio_* system calls.  There are numerous
  # stability and security issues in the current aio code that make it
  # unsuitable for inclusion on machines with untrusted local users.
  options         VFS_AIO
  
  # Cryptographically secure random number generator; /dev/random
  device          random
  
  # The system memory devices; /dev/mem, /dev/kmem
  device          mem
  
  # The kernel symbol table device; /dev/ksyms
  device          ksyms
  
  # Optional character code conversion support with LIBICONV.
  # Each option requires their base file system and LIBICONV.
  options         CD9660_ICONV
  options         MSDOSFS_ICONV
  options         UDF_ICONV
  
  
  #####################################################################
  # POSIX P1003.1B
  
  # Real time extensions added in the 1993 POSIX
  # _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
  
  options         _KPOSIX_PRIORITY_SCHEDULING
  # p1003_1b_semaphores are very experimental,
  # user should be ready to assist in debugging if problems arise.
  options         P1003_1B_SEMAPHORES
  
  # POSIX message queue
  options         P1003_1B_MQUEUE
  
  #####################################################################
  # SECURITY POLICY PARAMETERS
  
  # Support for BSM audit
  options         AUDIT
  
  # Support for Mandatory Access Control (MAC):
  options         MAC
  options         MAC_BIBA
  options         MAC_BSDEXTENDED
  options         MAC_IFOFF
  options         MAC_LOMAC
  options         MAC_MLS
  options         MAC_NONE
  options         MAC_PARTITION
  options         MAC_PORTACL
  options         MAC_SEEOTHERUIDS
  options         MAC_STUB
  options         MAC_TEST
  
  # Support for Capsicum
  options         CAPABILITIES    # fine-grained rights on file descriptors
  options         CAPABILITY_MODE # sandboxes with no global namespace access
  
  # Support for process descriptors
  options         PROCDESC
  
  
  #####################################################################
  # CLOCK OPTIONS
  
  # The granularity of operation is controlled by the kernel option HZ whose
  # default value (1000 on most architectures) means a granularity of 1ms
  # (1s/HZ).  Historically, the default was 100, but finer granularity is
  # required for DUMMYNET and other systems on modern hardware.  There are
  # reasonable arguments that HZ should, in fact, be 100 still; consider,
  # that reducing the granularity too much might cause excessive overhead in
  # clock interrupt processing, potentially causing ticks to be missed and thus
  # actually reducing the accuracy of operation.
  
  options         HZ=100
  
  # Enable support for the kernel PLL to use an external PPS signal,
  # under supervision of [x]ntpd(8)
  # More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
  
  options         PPS_SYNC
  
  # Enable support for generic feed-forward clocks in the kernel.
  # The feed-forward clock support is an alternative to the feedback oriented
  # ntpd/system clock approach, and is to be used with a feed-forward
  # synchronization algorithm such as the RADclock:
  # More info here: http://www.synclab.org/radclock
  
  options         FFCLOCK
  
  
  #####################################################################
  # SCSI DEVICES
  
  # SCSI DEVICE CONFIGURATION
  
  # The SCSI subsystem consists of the `base' SCSI code, a number of
  # high-level SCSI device `type' drivers, and the low-level host-adapter
  # device drivers.  The host adapters are listed in the ISA and PCI
  # device configuration sections below.
  #
  # It is possible to wire down your SCSI devices so that a given bus,
  # target, and LUN always come on line as the same device unit.  In
  # earlier versions the unit numbers were assigned in the order that
  # the devices were probed on the SCSI bus.  This means that if you
  # removed a disk drive, you may have had to rewrite your /etc/fstab
  # file, and also that you had to be careful when adding a new disk
  # as it may have been probed earlier and moved your device configuration
  # around.  (See also option GEOM_VOL for a different solution to this
  # problem.)
  
  # This old behavior is maintained as the default behavior.  The unit
  # assignment begins with the first non-wired down unit for a device
  # type.  For example, if you wire a disk as "da3" then the first
  # non-wired disk will be assigned da4.
  
  # The syntax for wiring down devices is:
  
  hint.scbus.0.at="ahc0"
  hint.scbus.1.at="ahc1"
  hint.scbus.1.bus="0"
  hint.scbus.3.at="ahc2"
  hint.scbus.3.bus="0"
  hint.scbus.2.at="ahc2"
  hint.scbus.2.bus="1"
  hint.da.0.at="scbus0"
  hint.da.0.target="0"
  hint.da.0.unit="0"
  hint.da.1.at="scbus3"
  hint.da.1.target="1"
  hint.da.2.at="scbus2"
  hint.da.2.target="3"
  hint.sa.1.at="scbus1"
  hint.sa.1.target="6"
  
  # "units" (SCSI logical unit number) that are not specified are
  # treated as if specified as LUN 0.
  
  # All SCSI devices allocate as many units as are required.
  
  # The ch driver drives SCSI Media Changer ("jukebox") devices.
  #
  # The da driver drives SCSI Direct Access ("disk") and Optical Media
  # ("WORM") devices.
  #
  # The sa driver drives SCSI Sequential Access ("tape") devices.
  #
  # The cd driver drives SCSI Read Only Direct Access ("cd") devices.
  #
  # The ses driver drives SCSI Environment Services ("ses") and
  # SAF-TE ("SCSI Accessible Fault-Tolerant Enclosure") devices.
  #
  # The pt driver drives SCSI Processor devices.
  #
  # The sg driver provides a passthrough API that is compatible with the
  # Linux SG driver.  It will work in conjunction with the COMPAT_LINUX
  # option to run linux SG apps.  It can also stand on its own and provide
  # source level API compatibility for porting apps to FreeBSD.
  #
  # Target Mode support is provided here but also requires that a SIM
  # (SCSI Host Adapter Driver) provide support as well.
  #
  # The targ driver provides target mode support as a Processor type device.
  # It exists to give the minimal context necessary to respond to Inquiry
  # commands. There is a sample user application that shows how the rest
  # of the command support might be done in /usr/share/examples/scsi_target.
  #
  # The targbh driver provides target mode support and exists to respond
  # to incoming commands that do not otherwise have a logical unit assigned
  # to them.
  #
  # The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
  # configuration as the "pass" driver.
  
  device          scbus           #base SCSI code
  device          ch              #SCSI media changers
  device          da              #SCSI direct access devices (aka disks)
  device          sa              #SCSI tapes
  device          cd              #SCSI CD-ROMs
  device          ses             #Enclosure Services (SES and SAF-TE)
  device          pt              #SCSI processor
  device          targ            #SCSI Target Mode Code
  device          targbh          #SCSI Target Mode Blackhole Device
  device          pass            #CAM passthrough driver
  device          sg              #Linux SCSI passthrough
  device          ctl             #CAM Target Layer
  
  # CAM OPTIONS:
  # debugging options:
  # CAMDEBUG              Compile in all possible debugging.
  # CAM_DEBUG_COMPILE     Debug levels to compile in.
  # CAM_DEBUG_FLAGS       Debug levels to enable on boot.
  # CAM_DEBUG_BUS         Limit debugging to the given bus.
  # CAM_DEBUG_TARGET      Limit debugging to the given target.
  # CAM_DEBUG_LUN         Limit debugging to the given lun.
  # CAM_DEBUG_DELAY       Delay in us after printing each debug line.
  #
  # CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
  # SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
  # SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
  # SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
  #             queue after a bus reset, and the number of milliseconds to
  #             freeze the device queue after a bus device reset.  This
  #             can be changed at boot and runtime with the
  #             kern.cam.scsi_delay tunable/sysctl.
  options         CAMDEBUG
  options         CAM_DEBUG_COMPILE=-1
  options         CAM_DEBUG_FLAGS=(CAM_DEBUG_INFO|CAM_DEBUG_PROBE|CAM_DEBUG_PERIPH)
  options         CAM_DEBUG_BUS=-1
  options         CAM_DEBUG_TARGET=-1
  options         CAM_DEBUG_LUN=-1
  options         CAM_DEBUG_DELAY=1
  options         CAM_MAX_HIGHPOWER=4
  options         SCSI_NO_SENSE_STRINGS
  options         SCSI_NO_OP_STRINGS
  options         SCSI_DELAY=5000 # Be pessimistic about Joe SCSI device
  
  # Options for the CAM CDROM driver:
  # CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
  # CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
  #                           enforced if there is I/O waiting for another LUN
  # The compiled in defaults for these variables are 2 and 10 seconds,
  # respectively.
  #
  # These can also be changed on the fly with the following sysctl variables:
  # kern.cam.cd.changer.min_busy_seconds
  # kern.cam.cd.changer.max_busy_seconds
  #
  options         CHANGER_MIN_BUSY_SECONDS=2
  options         CHANGER_MAX_BUSY_SECONDS=10
  
  # Options for the CAM sequential access driver:
  # SA_IO_TIMEOUT: Timeout for read/write/wfm  operations, in minutes
  # SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
  # SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
  # SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
  # SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
  options         SA_IO_TIMEOUT=4
  options         SA_SPACE_TIMEOUT=60
  options         SA_REWIND_TIMEOUT=(2*60)
  options         SA_ERASE_TIMEOUT=(4*60)
  options         SA_1FM_AT_EOD
  
  # Optional timeout for the CAM processor target (pt) device
  # This is specified in seconds.  The default is 60 seconds.
  options         SCSI_PT_DEFAULT_TIMEOUT=60
  
  # Optional enable of doing SES passthrough on other devices (e.g., disks)
  #
  # Normally disabled because a lot of newer SCSI disks report themselves
  # as having SES capabilities, but this can then clot up attempts to build
  # a topology with the SES device that's on the box these drives are in....
  options         SES_ENABLE_PASSTHROUGH
  
  
  #####################################################################
  # MISCELLANEOUS DEVICES AND OPTIONS
  
  device          pty             #BSD-style compatibility pseudo ttys
  device          nmdm            #back-to-back tty devices
  device          md              #Memory/malloc disk
  device          snp             #Snoop device - to look at pty/vty/etc..
  device          ccd             #Concatenated disk driver
  device          firmware        #firmware(9) support
  
  # Kernel side iconv library
  options         LIBICONV
  
  # Size of the kernel message buffer.  Should be N * pagesize.
  options         MSGBUF_SIZE=40960
  
  
  #####################################################################
  # HARDWARE DEVICE CONFIGURATION
  
  # For ISA the required hints are listed.
  # EISA, MCA, PCI, CardBus, SD/MMC and pccard are self identifying buses, so
  # no hints are needed.
  
  #
  # Mandatory devices:
  #
  
  # These options are valid for other keyboard drivers as well.
  options         KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
  options         KBD_INSTALL_CDEV        # install a CDEV entry in /dev
  
  options         FB_DEBUG                # Frame buffer debugging
  
  device          splash                  # Splash screen and screen saver support
  
  # Various screen savers.
  device          blank_saver
  device          daemon_saver
  device          dragon_saver
  device          fade_saver
  device          fire_saver
  device          green_saver
  device          logo_saver
  device          rain_saver
  device          snake_saver
  device          star_saver
  device          warp_saver
  
  # The syscons console driver (SCO color console compatible).
  device          sc
  hint.sc.0.at="isa"
  options         MAXCONS=16              # number of virtual consoles
  options         SC_ALT_MOUSE_IMAGE      # simplified mouse cursor in text mode
  options         SC_DFLT_FONT            # compile font in
  makeoptions     SC_DFLT_FONT=cp850
  options         SC_DISABLE_KDBKEY       # disable `debug' key
  options         SC_DISABLE_REBOOT       # disable reboot key sequence
  options         SC_HISTORY_SIZE=200     # number of history buffer lines
  options         SC_MOUSE_CHAR=0x3       # char code for text mode mouse cursor
  options         SC_PIXEL_MODE           # add support for the raster text mode
  
  # The following options will let you change the default colors of syscons.
  options         SC_NORM_ATTR=(FG_GREEN|BG_BLACK)
  options         SC_NORM_REV_ATTR=(FG_YELLOW|BG_GREEN)
  options         SC_KERNEL_CONS_ATTR=(FG_RED|BG_BLACK)
  options         SC_KERNEL_CONS_REV_ATTR=(FG_BLACK|BG_RED)
  
  # The following options will let you change the default behavior of
  # cut-n-paste feature
  options         SC_CUT_SPACES2TABS      # convert leading spaces into tabs
  options         SC_CUT_SEPCHARS=\"x09\" # set of characters that delimit words
                                          # (default is single space - \"x20\")
  
  # If you have a two button mouse, you may want to add the following option
  # to use the right button of the mouse to paste text.
  options         SC_TWOBUTTON_MOUSE
  
  # You can selectively disable features in syscons.
  options         SC_NO_CUTPASTE
  options         SC_NO_FONT_LOADING
  options         SC_NO_HISTORY
  options         SC_NO_MODE_CHANGE
  options         SC_NO_SYSMOUSE
  options         SC_NO_SUSPEND_VTYSWITCH
  
  # `flags' for sc
  #       0x80    Put the video card in the VESA 800x600 dots, 16 color mode
  #       0x100   Probe for a keyboard device periodically if one is not present
  
  # Enable experimental features of the syscons terminal emulator (teken).
  options         TEKEN_CONS25            # cons25-style terminal emulation
  options         TEKEN_UTF8              # UTF-8 output handling
  
  #
  # Optional devices:
  #
  
  #
  # SCSI host adapters:
  #
  # adv: All Narrow SCSI bus AdvanSys controllers.
  # adw: Second Generation AdvanSys controllers including the ADV940UW.
  # aha: Adaptec 154x/1535/1640
  # ahb: Adaptec 174x EISA controllers
  # ahc: Adaptec 274x/284x/2910/293x/294x/394x/3950x/3960x/398X/4944/
  #      19160x/29160x, aic7770/aic78xx
  # ahd: Adaptec 29320/39320 Controllers.
  # aic: Adaptec 6260/6360, APA-1460 (PC Card), NEC PC9801-100 (C-BUS)
  # bt:  Most Buslogic controllers: including BT-445, BT-54x, BT-64x, BT-74x,
  #      BT-75x, BT-946, BT-948, BT-956, BT-958, SDC3211B, SDC3211F, SDC3222F
  # esp: Emulex ESP, NCR 53C9x and QLogic FAS families based controllers
  #      including the AMD Am53C974 (found on devices such as the Tekram
  #      DC-390(T)) and the Sun ESP and FAS families of controllers
  # isp: Qlogic ISP 1020, 1040 and 1040B PCI SCSI host adapters,
  #      ISP 1240 Dual Ultra SCSI, ISP 1080 and 1280 (Dual) Ultra2,
  #      ISP 12160 Ultra3 SCSI,
  #      Qlogic ISP 2100 and ISP 2200 1Gb Fibre Channel host adapters.
  #      Qlogic ISP 2300 and ISP 2312 2Gb Fibre Channel host adapters.
  #      Qlogic ISP 2322 and ISP 6322 2Gb Fibre Channel host adapters.
  # ispfw: Firmware module for Qlogic host adapters
  # mpt: LSI-Logic MPT/Fusion 53c1020 or 53c1030 Ultra4
  #      or FC9x9 Fibre Channel host adapters.
  # ncr: NCR 53C810, 53C825 self-contained SCSI host adapters.
  # sym: Symbios/Logic 53C8XX family of PCI-SCSI I/O processors:
  #      53C810, 53C810A, 53C815, 53C825,  53C825A, 53C860, 53C875,
  #      53C876, 53C885,  53C895, 53C895A, 53C896,  53C897, 53C1510D,
  #      53C1010-33, 53C1010-66.
  # trm: Tekram DC395U/UW/F DC315U adapters.
  # wds: WD7000
  
  #
  # Note that the order is important in order for Buslogic ISA/EISA cards to be
  # probed correctly.
  #
  device          bt
  hint.bt.0.at="isa"
  hint.bt.0.port="0x330"
  device          adv
  hint.adv.0.at="isa"
  device          adw
  device          aha
  hint.aha.0.at="isa"
  device          aic
  hint.aic.0.at="isa"
  device          ahb
  device          ahc
  device          ahd
  device          esp
  device          iscsi_initiator
  device          isp
  hint.isp.0.disable="1"
  hint.isp.0.role="3"
  hint.isp.0.prefer_iomap="1"
  hint.isp.0.prefer_memmap="1"
  hint.isp.0.fwload_disable="1"
  hint.isp.0.ignore_nvram="1"
  hint.isp.0.fullduplex="1"
  hint.isp.0.topology="lport"
  hint.isp.0.topology="nport"
  hint.isp.0.topology="lport-only"
  hint.isp.0.topology="nport-only"
  # we can't get u_int64_t types, nor can we get strings if it's got
  # a leading 0x, hence this silly dodge.
  hint.isp.0.portwnn="w50000000aaaa0000"
  hint.isp.0.nodewnn="w50000000aaaa0001"
  device          ispfw
  device          mpt
  device          ncr
  device          sym
  device          trm
  device          wds
  hint.wds.0.at="isa"
  hint.wds.0.port="0x350"
  hint.wds.0.irq="11"
  hint.wds.0.drq="6"
  
  # The aic7xxx driver will attempt to use memory mapped I/O for all PCI
  # controllers that have it configured only if this option is set. Unfortunately,
  # this doesn't work on some motherboards, which prevents it from being the
  # default.
  options         AHC_ALLOW_MEMIO
  
  # Dump the contents of the ahc controller configuration PROM.
  options         AHC_DUMP_EEPROM
  
  # Bitmap of units to enable targetmode operations.
  options         AHC_TMODE_ENABLE
  
  # Compile in Aic7xxx Debugging code.
  options         AHC_DEBUG
  
  # Aic7xxx driver debugging options. See sys/dev/aic7xxx/aic7xxx.h
  options         AHC_DEBUG_OPTS
  
  # Print register bitfields in debug output.  Adds ~128k to driver
  # See ahc(4).
  options         AHC_REG_PRETTY_PRINT
  
  # Compile in aic79xx debugging code.
  options         AHD_DEBUG
  
  # Aic79xx driver debugging options.  Adds ~215k to driver.  See ahd(4).
  options         AHD_DEBUG_OPTS=0xFFFFFFFF
  
  # Print human-readable register definitions when debugging
  options         AHD_REG_PRETTY_PRINT
  
  # Bitmap of units to enable targetmode operations.
  options         AHD_TMODE_ENABLE
  
  # The adw driver will attempt to use memory mapped I/O for all PCI
  # controllers that have it configured only if this option is set.
  options         ADW_ALLOW_MEMIO
  
  # Options used in dev/iscsi (Software iSCSI stack)
  #
  options         ISCSI_INITIATOR_DEBUG=9
  
  # Options used in dev/isp/ (Qlogic SCSI/FC driver).
  #
  #       ISP_TARGET_MODE         -       enable target mode operation
  #
  options         ISP_TARGET_MODE=1
  #
  #       ISP_DEFAULT_ROLES       -       default role
  #               none=0
  #               target=1
  #               initiator=2
  #               both=3                  (not supported currently)
  #
  #       ISP_INTERNAL_TARGET             (trivial internal disk target, for testing)
  #
  options         ISP_DEFAULT_ROLES=0
  
  # Options used in dev/sym/ (Symbios SCSI driver).
  #options        SYM_SETUP_LP_PROBE_MAP  #-Low Priority Probe Map (bits)
                                          # Allows the ncr to take precedence
                                          # 1 (1<<0) -> 810a, 860
                                          # 2 (1<<1) -> 825a, 875, 885, 895
                                          # 4 (1<<2) -> 895a, 896, 1510d
  #options        SYM_SETUP_SCSI_DIFF     #-HVD support for 825a, 875, 885
                                          # disabled:0 (default), enabled:1
  #options        SYM_SETUP_PCI_PARITY    #-PCI parity checking
                                          # disabled:0, enabled:1 (default)
  #options        SYM_SETUP_MAX_LUN       #-Number of LUNs supported
                                          # default:8, range:[1..64]
  
  # The 'dpt' driver provides support for old DPT controllers (http://www.dpt.com/).
  # These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
  # The DPT controllers are commonly re-licensed under other brand-names -
  # some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
  # Compaq are actually DPT controllers.
  #
  # See src/sys/dev/dpt for debugging and other subtle options.
  #  DPT_MEASURE_PERFORMANCE  Enables a set of (semi)invasive metrics. Various
  #                           instruments are enabled.  The tools in
  #                           /usr/sbin/dpt_* assume these to be enabled.
  #  DPT_DEBUG_xxxx           These are controllable from sys/dev/dpt/dpt.h
  #  DPT_RESET_HBA            Make "reset" actually reset the controller
  #                           instead of fudging it.  Only enable this if you
  #                           are 100% certain you need it.
  
  device          dpt
  
  # DPT options
  #!CAM# options  DPT_MEASURE_PERFORMANCE
  options         DPT_RESET_HBA
  
  #
  # Compaq "CISS" RAID controllers (SmartRAID 5* series)
  # These controllers have a SCSI-like interface, and require the
  # CAM infrastructure.
  #
  device          ciss
  
  #
  # Intel Integrated RAID controllers.
  # This driver was developed and is maintained by Intel.  Contacts
  # at Intel for this driver are
  # "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com> and
  # "Leubner, Achim" <achim.leubner@intel.com>.
  #
  device          iir
  
  #
  # Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
  # firmware.  These controllers have a SCSI-like interface, and require
  # the CAM infrastructure.
  #
  device          mly
  
  #
  # Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers.  Only
  # one entry is needed; the code will find and configure all supported
  # controllers.
  #
  device          ida             # Compaq Smart RAID
  device          mlx             # Mylex DAC960
  device          amr             # AMI MegaRAID
  device          amrp            # SCSI Passthrough interface (optional, CAM req.)
  device          mfi             # LSI MegaRAID SAS
  device          mfip            # LSI MegaRAID SAS passthrough, requires CAM
  options         MFI_DEBUG
  
  #
  # 3ware ATA RAID
  #
  device          twe             # 3ware ATA RAID
  
  #
  # Serial ATA host controllers:
  #
  # ahci: Advanced Host Controller Interface (AHCI) compatible
  # mvs:  Marvell 88SX50XX/88SX60XX/88SX70XX/SoC controllers
  # siis: SiliconImage SiI3124/SiI3132/SiI3531 controllers
  #
  # These drivers are part of cam(4) subsystem. They supersede less featured
  # ata(4) subsystem drivers, supporting same hardware.
  
  device          ahci
  device          mvs
  device          siis
  
  #
  # The 'ATA' driver supports all legacy ATA/ATAPI controllers, including
  # PC Card devices. You only need one "device ata" for it to find all
  # PCI and PC Card ATA/ATAPI devices on modern machines.
  # Alternatively, individual bus and chipset drivers may be chosen by using
  # the 'atacore' driver then selecting the drivers on a per vendor basis.
  # For example to build a system which only supports a VIA chipset,
  # omit 'ata' and include the 'atacore', 'atapci' and 'atavia' drivers.
  device          ata
  
  # Modular ATA
  #device         atacore         # Core ATA functionality
  #device         atacard         # CARDBUS support
  #device         atabus          # PC98 cbus support
  #device         ataisa          # ISA bus support
  #device         atapci          # PCI bus support; only generic chipset support
  
  # PCI ATA chipsets
  #device         ataahci         # AHCI SATA
  #device         ataacard        # ACARD
  #device         ataacerlabs     # Acer Labs Inc. (ALI)
  #device         ataadaptec      # Adaptec
  #device         ataamd          # American Micro Devices (AMD)
  #device         ataati          # ATI
  #device         atacenatek      # Cenatek
  #device         atacypress      # Cypress
  #device         atacyrix        # Cyrix
  #device         atahighpoint    # HighPoint
  #device         ataintel        # Intel
  #device         ataite          # Integrated Technology Inc. (ITE)
  #device         atajmicron      # JMicron
  #device         atamarvell      # Marvell
  #device         atamicron       # Micron
  #device         atanational     # National
  #device         atanetcell      # NetCell
  #device         atanvidia       # nVidia
  #device         atapromise      # Promise
  #device         ataserverworks  # ServerWorks
  #device         atasiliconimage # Silicon Image Inc. (SiI) (formerly CMD)
  #device         atasis          # Silicon Integrated Systems Corp.(SiS)
  #device         atavia          # VIA Technologies Inc.
  
  #
  # For older non-PCI, non-PnPBIOS systems, these are the hints lines to add:
  hint.ata.0.at="isa"
  hint.ata.0.port="0x1f0"
  hint.ata.0.irq="14"
  hint.ata.1.at="isa"
  hint.ata.1.port="0x170"
  hint.ata.1.irq="15"
  
  #
  # The following options are valid on the ATA driver:
  #
  # ATA_STATIC_ID:        controller numbering is static ie depends on location
  #                       else the device numbers are dynamically allocated.
  # ATA_REQUEST_TIMEOUT:  the number of seconds to wait for an ATA request
  #                       before timing out.
  
  options         ATA_STATIC_ID
  #options        ATA_REQUEST_TIMEOUT=10
  
  #
  # Standard floppy disk controllers and floppy tapes, supports
  # the Y-E DATA External FDD (PC Card)
  #
  device          fdc
  hint.fdc.0.at="isa"
  hint.fdc.0.port="0x3F0"
  hint.fdc.0.irq="6"
  hint.fdc.0.drq="2"
  #
  # FDC_DEBUG enables floppy debugging.  Since the debug output is huge, you
  # gotta turn it actually on by setting the variable fd_debug with DDB,
  # however.
  options         FDC_DEBUG
  #
  # Activate this line if you happen to have an Insight floppy tape.
  # Probing them proved to be dangerous for people with floppy disks only,
  # so it's "hidden" behind a flag:
  #hint.fdc.0.flags="1"
  
  # Specify floppy devices
  hint.fd.0.at="fdc0"
  hint.fd.0.drive="0"
  hint.fd.1.at="fdc0"
  hint.fd.1.drive="1"
  
  #
  # uart: newbusified driver for serial interfaces.  It consolidates the sio(4),
  #       sab(4) and zs(4) drivers.
  #
  device          uart
  
  # Options for uart(4)
  options         UART_PPS_ON_CTS         # Do time pulse capturing using CTS
                                          # instead of DCD.
  options         UART_POLL_FREQ          # Set polling rate, used when hw has
                                          # no interrupt support (50 Hz default).
  
  # The following hint should only be used for pure ISA devices.  It is not
  # needed otherwise.  Use of hints is strongly discouraged.
  hint.uart.0.at="isa"
  
  # The following 3 hints are used when the UART is a system device (i.e., a
  # console or debug port), but only on platforms that don't have any other
  # means to pass the information to the kernel.  The unit number of the hint
  # is only used to bundle the hints together.  There is no relation to the
  # unit number of the probed UART.
  hint.uart.0.port="0x3f8"
  hint.uart.0.flags="0x10"
  hint.uart.0.baud="115200"
  
  # `flags' for serial drivers that support consoles like sio(4) and uart(4):
  #       0x10    enable console support for this unit.  Other console flags
  #               (if applicable) are ignored unless this is set.  Enabling
  #               console support does not make the unit the preferred console.
  #               Boot with -h or set boot_serial=YES in the loader.  For sio(4)
  #               specifically, the 0x20 flag can also be set (see above).
  #               Currently, at most one unit can have console support; the
  #               first one (in config file order) with this flag set is
  #               preferred.  Setting this flag for sio0 gives the old behavior.
  #       0x80    use this port for serial line gdb support in ddb.  Also known
  #               as debug port.
  #
  
  # Options for serial drivers that support consoles:
  options         BREAK_TO_DEBUGGER       # A BREAK on a serial console goes to
                                          # ddb, if available.
  
  # Solaris implements a new BREAK which is initiated by a character
  # sequence CR ~ ^b which is similar to a familiar pattern used on
  # Sun servers by the Remote Console.  There are FreeBSD extensions:
  # CR ~ ^p requests force panic and CR ~ ^r requests a clean reboot.
  options         ALT_BREAK_TO_DEBUGGER
  
  # Serial Communications Controller
  # Supports the Siemens SAB 82532 and Zilog Z8530 multi-channel
  # communications controllers.
  device          scc
  
  # PCI Universal Communications driver
  # Supports various multi port PCI I/O cards.
  device          puc
  
  #
  # Network interfaces:
  #
  # MII bus support is required for many PCI Ethernet NICs,
  # namely those which use MII-compliant transceivers or implement
  # transceiver control interfaces that operate like an MII.  Adding
  # "device miibus" to the kernel config pulls in support for the generic
  # miibus API, the common support for for bit-bang'ing the MII and all
  # of the PHY drivers, including a generic one for PHYs that aren't
  # specifically handled by an individual driver.  Support for specific
  # PHYs may be built by adding "device mii", "device mii_bitbang" if
  # needed by the NIC driver and then adding the appropriate PHY driver.
  device          mii             # Minimal MII support
  device          mii_bitbang     # Common module for bit-bang'ing the MII
  device          miibus          # MII support w/ bit-bang'ing and all PHYs
  
  device          acphy           # Altima Communications AC101
  device          amphy           # AMD AM79c873 / Davicom DM910{1,2}
  device          atphy           # Attansic/Atheros F1
  device          axphy           # Asix Semiconductor AX88x9x
  device          bmtphy          # Broadcom BCM5201/BCM5202 and 3Com 3c905C
  device          brgphy          # Broadcom BCM54xx/57xx 1000baseTX
  device          ciphy           # Cicada/Vitesse CS/VSC8xxx
  device          e1000phy        # Marvell 88E1000 1000/100/10-BT
  device          gentbi          # Generic 10-bit 1000BASE-{LX,SX} fiber ifaces
  device          icsphy          # ICS ICS1889-1893
  device          ip1000phy       # IC Plus IP1000A/IP1001
  device          jmphy           # JMicron JMP211/JMP202
  device          lxtphy          # Level One LXT-970
  device          mlphy           # Micro Linear 6692
  device          nsgphy          # NatSemi DP8361/DP83865/DP83891
  device          nsphy           # NatSemi DP83840A
  device          nsphyter        # NatSemi DP83843/DP83815
  device          pnaphy          # HomePNA
  device          qsphy           # Quality Semiconductor QS6612
  device          rdcphy          # RDC Semiconductor R6040
  device          rgephy          # RealTek 8169S/8110S/8211B/8211C
  device          rlphy           # RealTek 8139
  device          rlswitch        # RealTek 8305
  device          smcphy          # SMSC LAN91C111
  device          tdkphy          # TDK 89Q2120
  device          tlphy           # Texas Instruments ThunderLAN
  device          truephy         # LSI TruePHY
  device          xmphy           # XaQti XMAC II
  
  # an:   Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
  #       PCI and ISA varieties.
  # ae:   Support for gigabit ethernet adapters based on the Attansic/Atheros
  #       L2 PCI-Express FastEthernet controllers.
  # age:  Support for gigabit ethernet adapters based on the Attansic/Atheros
  #       L1 PCI express gigabit ethernet controllers.
  # alc:  Support for Atheros AR8131/AR8132 PCIe ethernet controllers.
  # ale:  Support for Atheros AR8121/AR8113/AR8114 PCIe ethernet controllers.
  # ath:  Atheros a/b/g WiFi adapters (requires ath_hal and wlan)
  # bce:  Broadcom NetXtreme II (BCM5706/BCM5708) PCI/PCIe Gigabit Ethernet
  #       adapters.
  # bfe:  Broadcom BCM4401 Ethernet adapter.
  # bge:  Support for gigabit ethernet adapters based on the Broadcom
  #       BCM570x family of controllers, including the 3Com 3c996-T,
  #       the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41, and
  #       the embedded gigE NICs on Dell PowerEdge 2550 servers.
  # bxe:  Broadcom NetXtreme II (BCM5771X/BCM578XX) PCIe 10Gb Ethernet
  #       adapters.
  # bwi:  Broadcom BCM430* and BCM431* family of wireless adapters.
  # bwn:  Broadcom BCM43xx family of wireless adapters.
  # cas:  Sun Cassini/Cassini+ and National Semiconductor DP83065 Saturn
  # cm:   Arcnet SMC COM90c26 / SMC COM90c56
  #       (and SMC COM90c66 in '56 compatibility mode) adapters.
  # cxgbe: Support for PCI express 10Gb/1Gb adapters based on the Chelsio T4
  #       (Terminator 4) ASIC.
  # dc:   Support for PCI fast ethernet adapters based on the DEC/Intel 21143
  #       and various workalikes including:
  #       the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
  #       AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
  #       82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
  #       and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
  #       replaces the old al, ax, dm, pn and mx drivers.  List of brands:
  #       Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
  #       SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
  #       LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
  #       KNE110TX.
  # de:   Digital Equipment DC21040
  # em:   Intel Pro/1000 Gigabit Ethernet 82542, 82543, 82544 based adapters.
  # igb:  Intel Pro/1000 PCI Express Gigabit Ethernet: 82575 and later adapters.
  # ep:   3Com 3C509, 3C529, 3C556, 3C562D, 3C563D, 3C572, 3C574X, 3C579, 3C589
  #       and PC Card devices using these chipsets.
  # ex:   Intel EtherExpress Pro/10 and other i82595-based adapters,
  #       Olicom Ethernet PC Card devices.
  # fe:   Fujitsu MB86960A/MB86965A Ethernet
  # fea:  DEC DEFEA EISA FDDI adapter
  # fpa:  Support for the Digital DEFPA PCI FDDI. `device fddi' is also needed.
  # fxp:  Intel EtherExpress Pro/100B
  #       (hint of prefer_iomap can be done to prefer I/O instead of Mem mapping)
  # gem:  Apple GMAC/Sun ERI/Sun GEM
  # hme:  Sun HME (Happy Meal Ethernet)
  # jme:  JMicron JMC260 Fast Ethernet/JMC250 Gigabit Ethernet based adapters.
  # le:   AMD Am7900 LANCE and Am79C9xx PCnet
  # lge:  Support for PCI gigabit ethernet adapters based on the Level 1
  #       LXT1001 NetCellerator chipset. This includes the D-Link DGE-500SX,
  #       SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
  # malo: Marvell Libertas wireless NICs.
  # mwl:  Marvell 88W8363 802.11n wireless NICs.
  #       Requires the mwl firmware module
  # mwlfw: Marvell 88W8363 firmware
  # msk:  Support for gigabit ethernet adapters based on the Marvell/SysKonnect
  #       Yukon II Gigabit controllers, including 88E8021, 88E8022, 88E8061,
  #       88E8062, 88E8035, 88E8036, 88E8038, 88E8050, 88E8052, 88E8053,
  #       88E8055, 88E8056 and D-Link 560T/550SX.
  # lmc:  Support for the LMC/SBE wide-area network interface cards.
  # my:   Myson Fast Ethernet (MTD80X, MTD89X)
  # nge:  Support for PCI gigabit ethernet adapters based on the National
  #       Semiconductor DP83820 and DP83821 chipset. This includes the
  #       SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante FriendlyNet
  #       GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the Surecom
  #       EP-320G-TX and the Netgear GA622T.
  # oce:  Emulex 10 Gbit adapters (OneConnect Ethernet)
  # pcn:  Support for PCI fast ethernet adapters based on the AMD Am79c97x
  #       PCnet-FAST, PCnet-FAST+, PCnet-FAST III, PCnet-PRO and PCnet-Home
  #       chipsets. These can also be handled by the le(4) driver if the
  #       pcn(4) driver is left out of the kernel. The le(4) driver does not
  #       support the additional features like the MII bus and burst mode of
  #       the PCnet-FAST and greater chipsets though.
  # ral:  Ralink Technology IEEE 802.11 wireless adapter
  # re:   RealTek 8139C+/8169/816xS/811xS/8101E PCI/PCIe Ethernet adapter
  # rl:   Support for PCI fast ethernet adapters based on the RealTek 8129/8139
  #       chipset.  Note that the RealTek driver defaults to using programmed
  #       I/O to do register accesses because memory mapped mode seems to cause
  #       severe lockups on SMP hardware.  This driver also supports the
  #       Accton EN1207D `Cheetah' adapter, which uses a chip called
  #       the MPX 5030/5038, which is either a RealTek in disguise or a
  #       RealTek workalike.  Note that the D-Link DFE-530TX+ uses the RealTek
  #       chipset and is supported by this driver, not the 'vr' driver.
  # sf:   Support for Adaptec Duralink PCI fast ethernet adapters based on the
  #       Adaptec AIC-6915 "starfire" controller.
  #       This includes dual and quad port cards, as well as one 100baseFX card.
  #       Most of these are 64-bit PCI devices, except for one single port
  #       card which is 32-bit.
  # sge:  Silicon Integrated Systems SiS190/191 Fast/Gigabit Ethernet adapter
  # sis:  Support for NICs based on the Silicon Integrated Systems SiS 900,
  #       SiS 7016 and NS DP83815 PCI fast ethernet controller chips.
  # sk:   Support for the SysKonnect SK-984x series PCI gigabit ethernet NICs.
  #       This includes the SK-9841 and SK-9842 single port cards (single mode
  #       and multimode fiber) and the SK-9843 and SK-9844 dual port cards
  #       (also single mode and multimode).
  #       The driver will autodetect the number of ports on the card and
  #       attach each one as a separate network interface.
  # sn:   Support for ISA and PC Card Ethernet devices using the
  #       SMC91C90/92/94/95 chips.
  # ste:  Sundance Technologies ST201 PCI fast ethernet controller, includes
  #       the D-Link DFE-550TX.
  # stge: Support for gigabit ethernet adapters based on the Sundance/Tamarack
  #       TC9021 family of controllers, including the Sundance ST2021/ST2023,
  #       the Sundance/Tamarack TC9021, the D-Link DL-4000 and ASUS NX1101.
  # ti:   Support for PCI gigabit ethernet NICs based on the Alteon Networks
  #       Tigon 1 and Tigon 2 chipsets.  This includes the Alteon AceNIC, the
  #       3Com 3c985, the Netgear GA620 and various others.  Note that you will
  #       probably want to bump up kern.ipc.nmbclusters a lot to use this driver.
  # tl:   Support for the Texas Instruments TNETE100 series 'ThunderLAN'
  #       cards and integrated ethernet controllers.  This includes several
  #       Compaq Netelligent 10/100 cards and the built-in ethernet controllers
  #       in several Compaq Prosignia, Proliant and Deskpro systems.  It also
  #       supports several Olicom 10Mbps and 10/100 boards.
  # tx:   SMC 9432 TX, BTX and FTX cards. (SMC EtherPower II series)
  # txp:  Support for 3Com 3cR990 cards with the "Typhoon" chipset
  # vr:   Support for various fast ethernet adapters based on the VIA
  #       Technologies VT3043 `Rhine I' and VT86C100A `Rhine II' chips,
  #       including the D-Link DFE520TX and D-Link DFE530TX (see 'rl' for
  #       DFE530TX+), the Hawking Technologies PN102TX, and the AOpen/Acer ALN-320.
  # vte:  DM&P Vortex86 RDC R6040 Fast Ethernet
  # vx:   3Com 3C590 and 3C595
  # wb:   Support for fast ethernet adapters based on the Winbond W89C840F chip.
  #       Note: this is not the same as the Winbond W89C940F, which is a
  #       NE2000 clone.
  # wi:   Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
  #       the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
  #       bridge with a PCMCIA adapter plugged into it.
  # xe:   Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller,
  #       Accton Fast EtherCard-16, Compaq Netelligent 10/100 PC Card,
  #       Toshiba 10/100 Ethernet PC Card, Xircom 16-bit Ethernet + Modem 56
  # xl:   Support for the 3Com 3c900, 3c905, 3c905B and 3c905C (Fast)
  #       Etherlink XL cards and integrated controllers.  This includes the
  #       integrated 3c905B-TX chips in certain Dell Optiplex and Dell
  #       Precision desktop machines and the integrated 3c905-TX chips
  #       in Dell Latitude laptop docking stations.
  #       Also supported: 3Com 3c980(C)-TX, 3Com 3cSOHO100-TX, 3Com 3c450-TX
  
  # Order for ISA/EISA devices is important here
  
  device          cm
  hint.cm.0.at="isa"
  hint.cm.0.port="0x2e0"
  hint.cm.0.irq="9"
  hint.cm.0.maddr="0xdc000"
  device          ep
  device          ex
  device          fe
  hint.fe.0.at="isa"
  hint.fe.0.port="0x300"
  device          fea
  device          sn
  hint.sn.0.at="isa"
  hint.sn.0.port="0x300"
  hint.sn.0.irq="10"
  device          an
  device          wi
  device          xe
  
  # PCI Ethernet NICs that use the common MII bus controller code.
  device          ae              # Attansic/Atheros L2 FastEthernet
  device          age             # Attansic/Atheros L1 Gigabit Ethernet
  device          alc             # Atheros AR8131/AR8132 Ethernet
  device          ale             # Atheros AR8121/AR8113/AR8114 Ethernet
  device          bce             # Broadcom BCM5706/BCM5708 Gigabit Ethernet
  device          bfe             # Broadcom BCM440x 10/100 Ethernet
  device          bge             # Broadcom BCM570xx Gigabit Ethernet
  device          cas             # Sun Cassini/Cassini+ and NS DP83065 Saturn
  device          cxgb            # Chelsio T3 10 Gigabit Ethernet
  device          cxgb_t3fw       # Chelsio T3 10 Gigabit Ethernet firmware
  device          dc              # DEC/Intel 21143 and various workalikes
  device          et              # Agere ET1310 10/100/Gigabit Ethernet
  device          fxp             # Intel EtherExpress PRO/100B (82557, 82558)
  hint.fxp.0.prefer_iomap="0"
  device          gem             # Apple GMAC/Sun ERI/Sun GEM
  device          hme             # Sun HME (Happy Meal Ethernet)
  device          jme             # JMicron JMC250 Gigabit/JMC260 Fast Ethernet
  device          lge             # Level 1 LXT1001 gigabit Ethernet
  device          msk             # Marvell/SysKonnect Yukon II Gigabit Ethernet
  device          my              # Myson Fast Ethernet (MTD80X, MTD89X)
  device          nge             # NatSemi DP83820 gigabit Ethernet
  device          re              # RealTek 8139C+/8169/8169S/8110S
  device          rl              # RealTek 8129/8139
  device          pcn             # AMD Am79C97x PCI 10/100 NICs
  device          sf              # Adaptec AIC-6915 (``Starfire'')
  device          sge             # Silicon Integrated Systems SiS190/191
  device          sis             # Silicon Integrated Systems SiS 900/SiS 7016
  device          sk              # SysKonnect SK-984x & SK-982x gigabit Ethernet
  device          ste             # Sundance ST201 (D-Link DFE-550TX)
  device          stge            # Sundance/Tamarack TC9021 gigabit Ethernet
  device          tl              # Texas Instruments ThunderLAN
  device          tx              # SMC EtherPower II (83c170 ``EPIC'')
  device          vr              # VIA Rhine, Rhine II
  device          vte             # DM&P Vortex86 RDC R6040 Fast Ethernet
  device          wb              # Winbond W89C840F
  device          xl              # 3Com 3c90x (``Boomerang'', ``Cyclone'')
  
  # PCI Ethernet NICs.
  device          cxgbe           # Chelsio T4 10GbE PCIe adapter
  device          de              # DEC/Intel DC21x4x (``Tulip'')
  device          em              # Intel Pro/1000 Gigabit Ethernet
  device          igb             # Intel Pro/1000 PCIE Gigabit Ethernet
  device          ixgb            # Intel Pro/10Gbe PCI-X Ethernet
  device          ixgbe           # Intel Pro/10Gbe PCIE Ethernet
  device          le              # AMD Am7900 LANCE and Am79C9xx PCnet
  device          mxge            # Myricom Myri-10G 10GbE NIC
  device          nxge            # Neterion Xframe 10GbE Server/Storage Adapter
  device          oce             # Emulex 10 GbE (OneConnect Ethernet)
  device          ti              # Alteon Networks Tigon I/II gigabit Ethernet
  device          txp             # 3Com 3cR990 (``Typhoon'')
  device          vx              # 3Com 3c590, 3c595 (``Vortex'')
  device          vxge            # Exar/Neterion XFrame 3100 10GbE
  
  # PCI FDDI NICs.
  device          fpa
  
  # PCI WAN adapters.
  device          lmc
  
  # PCI IEEE 802.11 Wireless NICs
  device          ath             # Atheros pci/cardbus NIC's
  device          ath_hal         # pci/cardbus chip support
  #device         ath_ar5210      # AR5210 chips
  #device         ath_ar5211      # AR5211 chips
  #device         ath_ar5212      # AR5212 chips
  #device         ath_rf2413
  #device         ath_rf2417
  #device         ath_rf2425
  #device         ath_rf5111
  #device         ath_rf5112
  #device         ath_rf5413
  #device         ath_ar5416      # AR5416 chips
  options         AH_SUPPORT_AR5416       # enable AR5416 tx/rx descriptors
  # All of the AR5212 parts have a problem when paired with the AR71xx
  # CPUS.  These parts have a bug that triggers a fatal bus error on the AR71xx
  # only.  Details of the exact nature of the bug are sketchy, but some can be
  # found at https://forum.openwrt.org/viewtopic.php?pid=70060 on pages 4, 5 and
  # 6.  This option enables this workaround.  There is a performance penalty
  # for this work around, but without it things don't work at all.  The DMA
  # from the card usually bursts 128 bytes, but on the affected CPUs, only
  # 4 are safe.
  options         AH_RXCFG_SDMAMW_4BYTES
  #device         ath_ar9160      # AR9160 chips
  #device         ath_ar9280      # AR9280 chips
  #device         ath_ar9285      # AR9285 chips
  device          ath_rate_sample # SampleRate tx rate control for ath
  device          bwi             # Broadcom BCM430* BCM431*
  device          bwn             # Broadcom BCM43xx
  device          malo            # Marvell Libertas wireless NICs.
  device          mwl             # Marvell 88W8363 802.11n wireless NICs.
  device          mwlfw
  device          ral             # Ralink Technology RT2500 wireless NICs.
  
  # Use sf_buf(9) interface for jumbo buffers on ti(4) controllers.
  #options        TI_SF_BUF_JUMBO
  # Turn on the header splitting option for the ti(4) driver firmware.  This
  # only works for Tigon II chips, and has no effect for Tigon I chips.
  # This option requires the TI_SF_BUF_JUMBO option above.
  #options        TI_JUMBO_HDRSPLIT
  
  # These two options allow manipulating the mbuf cluster size and mbuf size,
  # respectively.  Be very careful with NIC driver modules when changing
  # these from their default values, because that can potentially cause a
  # mismatch between the mbuf size assumed by the kernel and the mbuf size
  # assumed by a module.  The only driver that currently has the ability to
  # detect a mismatch is ti(4).
  options         MCLSHIFT=12     # mbuf cluster shift in bits, 12 == 4KB
  options         MSIZE=512       # mbuf size in bytes
  
  #
  # ATM related options (Cranor version)
  # (note: this driver cannot be used with the HARP ATM stack)
  #
  # The `en' device provides support for Efficient Networks (ENI)
  # ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
  #
  # The `hatm' device provides support for Fore/Marconi HE155 and HE622
  # ATM PCI cards.
  #
  # The `fatm' device provides support for Fore PCA200E ATM PCI cards.
  #
  # The `patm' device provides support for IDT77252 based cards like
  # ProSum's ProATM-155 and ProATM-25 and IDT's evaluation boards.
  #
  # atm device provides generic atm functions and is required for
  # atm devices.
  # NATM enables the netnatm protocol family that can be used to
  # bypass TCP/IP.
  #
  # utopia provides the access to the ATM PHY chips and is required for en,
  # hatm and fatm.
  #
  # the current driver supports only PVC operations (no atm-arp, no multicast).
  # for more details, please read the original documents at
  # http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
  #
  device          atm
  device          en
  device          fatm                    #Fore PCA200E
  device          hatm                    #Fore/Marconi HE155/622
  device          patm                    #IDT77252 cards (ProATM and IDT)
  device          utopia                  #ATM PHY driver
  options         NATM                    #native ATM
  
  options         LIBMBPOOL               #needed by patm, iatm
  
  #
  # Sound drivers
  #
  # sound: The generic sound driver.
  #
  
  device          sound
  
  #
  # snd_*: Device-specific drivers.
  #
  # The flags of the device tell the device a bit more info about the
  # device that normally is obtained through the PnP interface.
  #       bit  2..0   secondary DMA channel;
  #       bit  4      set if the board uses two dma channels;
  #       bit 15..8   board type, overrides autodetection; leave it
  #                   zero if don't know what to put in (and you don't,
  #                   since this is unsupported at the moment...).
  #
  # snd_ad1816:           Analog Devices AD1816 ISA PnP/non-PnP.
  # snd_als4000:          Avance Logic ALS4000 PCI.
  # snd_atiixp:           ATI IXP 200/300/400 PCI.
  # snd_audiocs:          Crystal Semiconductor CS4231 SBus/EBus. Only
  #                       for sparc64.
  # snd_cmi:              CMedia CMI8338/CMI8738 PCI.
  # snd_cs4281:           Crystal Semiconductor CS4281 PCI.
  # snd_csa:              Crystal Semiconductor CS461x/428x PCI. (except
  #                       4281)
  # snd_ds1:              Yamaha DS-1 PCI.
  # snd_emu10k1:          Creative EMU10K1 PCI and EMU10K2 (Audigy) PCI.
  # snd_emu10kx:          Creative SoundBlaster Live! and Audigy
  # snd_envy24:           VIA Envy24 and compatible, needs snd_spicds.
  # snd_envy24ht:         VIA Envy24HT and compatible, needs snd_spicds.
  # snd_es137x:           Ensoniq AudioPCI ES137x PCI.
  # snd_ess:              Ensoniq ESS ISA PnP/non-PnP, to be used in
  #                       conjunction with snd_sbc.
  # snd_fm801:            Forte Media FM801 PCI.
  # snd_gusc:             Gravis UltraSound ISA PnP/non-PnP.
  # snd_hda:              Intel High Definition Audio (Controller) and
  #                       compatible.
  # snd_hdspe:            RME HDSPe AIO and RayDAT.
  # snd_ich:              Intel ICH AC'97 and some more audio controllers
  #                       embedded in a chipset, for example nVidia
  #                       nForce controllers.
  # snd_maestro:          ESS Technology Maestro-1/2x PCI.
  # snd_maestro3:         ESS Technology Maestro-3/Allegro PCI.
  # snd_mss:              Microsoft Sound System ISA PnP/non-PnP.
  # snd_neomagic:         Neomagic 256 AV/ZX PCI.
  # snd_sb16:             Creative SoundBlaster16, to be used in
  #                       conjunction with snd_sbc.
  # snd_sb8:              Creative SoundBlaster (pre-16), to be used in
  #                       conjunction with snd_sbc.
  # snd_sbc:              Creative SoundBlaster ISA PnP/non-PnP.
  #                       Supports ESS and Avance ISA chips as well.
  # snd_solo:             ESS Solo-1x PCI.
  # snd_spicds:           SPI codec driver, needed by Envy24/Envy24HT drivers.
  # snd_t4dwave:          Trident 4DWave DX/NX PCI, Sis 7018 PCI and Acer Labs
  #                       M5451 PCI.
  # snd_uaudio:           USB audio.
  # snd_via8233:          VIA VT8233x PCI.
  # snd_via82c686:        VIA VT82C686A PCI.
  # snd_vibes:            S3 Sonicvibes PCI.
  
  device          snd_ad1816
  device          snd_als4000
  device          snd_atiixp
  #device         snd_audiocs
  device          snd_cmi
  device          snd_cs4281
  device          snd_csa
  device          snd_ds1
  device          snd_emu10k1
  device          snd_emu10kx
  device          snd_envy24
  device          snd_envy24ht
  device          snd_es137x
  device          snd_ess
  device          snd_fm801
  device          snd_gusc
  device          snd_hda
  device          snd_hdspe
  device          snd_ich
  device          snd_maestro
  device          snd_maestro3
  device          snd_mss
  device          snd_neomagic
  device          snd_sb16
  device          snd_sb8
  device          snd_sbc
  device          snd_solo
  device          snd_spicds
  device          snd_t4dwave
  device          snd_uaudio
  device          snd_via8233
  device          snd_via82c686
  device          snd_vibes
  
  # For non-PnP sound cards:
  hint.pcm.0.at="isa"
  hint.pcm.0.irq="10"
  hint.pcm.0.drq="1"
  hint.pcm.0.flags="0x0"
  hint.sbc.0.at="isa"
  hint.sbc.0.port="0x220"
  hint.sbc.0.irq="5"
  hint.sbc.0.drq="1"
  hint.sbc.0.flags="0x15"
  hint.gusc.0.at="isa"
  hint.gusc.0.port="0x220"
  hint.gusc.0.irq="5"
  hint.gusc.0.drq="1"
  hint.gusc.0.flags="0x13"
  
  #
  # Following options are intended for debugging/testing purposes:
  #
  # SND_DEBUG                    Enable extra debugging code that includes
  #                              sanity checking and possible increase of
  #                              verbosity.
  #
  # SND_DIAGNOSTIC               Similar in a spirit of INVARIANTS/DIAGNOSTIC,
  #                              zero tolerance against inconsistencies.
  #
  # SND_FEEDER_MULTIFORMAT       By default, only 16/32 bit feeders are compiled
  #                              in. This options enable most feeder converters
  #                              except for 8bit. WARNING: May bloat the kernel.
  #
  # SND_FEEDER_FULL_MULTIFORMAT  Ditto, but includes 8bit feeders as well.
  #
  # SND_FEEDER_RATE_HP           (feeder_rate) High precision 64bit arithmetic
  #                              as much as possible (the default trying to
  #                              avoid it). Possible slowdown.
  #
  # SND_PCM_64                   (Only applicable for i386/32bit arch)
  #                              Process 32bit samples through 64bit
  #                              integer/arithmetic. Slight increase of dynamic
  #                              range at a cost of possible slowdown.
  #
  # SND_OLDSTEREO                Only 2 channels are allowed, effectively
  #                              disabling multichannel processing.
  #
  options         SND_DEBUG
  options         SND_DIAGNOSTIC
  options         SND_FEEDER_MULTIFORMAT
  options         SND_FEEDER_FULL_MULTIFORMAT
  options         SND_FEEDER_RATE_HP
  options         SND_PCM_64
  options         SND_OLDSTEREO
  
  #
  # IEEE-488 hardware:
  # pcii:         PCIIA cards (uPD7210 based isa cards)
  # tnt4882:      National Instruments PCI-GPIB card.
  
  device  pcii
  hint.pcii.0.at="isa"
  hint.pcii.0.port="0x2e1"
  hint.pcii.0.irq="5"
  hint.pcii.0.drq="1"
  
  device  tnt4882
  
  #
  # Miscellaneous hardware:
  #
  # scd: Sony CD-ROM using proprietary (non-ATAPI) interface
  # mcd: Mitsumi CD-ROM using proprietary (non-ATAPI) interface
  # bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
  # joy: joystick (including IO DATA PCJOY PC Card joystick)
  # cmx: OmniKey CardMan 4040 pccard smartcard reader
  
  # Mitsumi CD-ROM
  device          mcd
  hint.mcd.0.at="isa"
  hint.mcd.0.port="0x300"
  # for the Sony CDU31/33A CDROM
  device          scd
  hint.scd.0.at="isa"
  hint.scd.0.port="0x230"
  device          joy                     # PnP aware, hints for non-PnP only
  hint.joy.0.at="isa"
  hint.joy.0.port="0x201"
  device          cmx
  
  #
  # The 'bktr' device is a PCI video capture device using the Brooktree
  # bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
  # TV card, e.g. Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
  # Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
  #
  # options       OVERRIDE_CARD=xxx
  # options       OVERRIDE_TUNER=xxx
  # options       OVERRIDE_MSP=1
  # options       OVERRIDE_DBX=1
  # These options can be used to override the auto detection
  # The current values for xxx are found in src/sys/dev/bktr/bktr_card.h
  # Using sysctl(8) run-time overrides on a per-card basis can be made
  #
  # options       BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_PAL
  # or
  # options       BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_NTSC
  # Specifies the default video capture mode.
  # This is required for Dual Crystal (28&35MHz) boards where PAL is used
  # to prevent hangs during initialization, e.g. VideoLogic Captivator PCI.
  #
  # options       BKTR_USE_PLL
  # This is required for PAL or SECAM boards with a 28MHz crystal and no 35MHz
  # crystal, e.g. some new Bt878 cards.
  #
  # options       BKTR_GPIO_ACCESS
  # This enables IOCTLs which give user level access to the GPIO port.
  #
  # options       BKTR_NO_MSP_RESET
  # Prevents the MSP34xx reset. Good if you initialize the MSP in another OS first
  #
  # options       BKTR_430_FX_MODE
  # Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
  #
  # options       BKTR_SIS_VIA_MODE
  # Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
  # needed for some old SiS and VIA chipset motherboards.
  # This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
  # motherboards and motherboards with bad or incomplete PCI 2.1 support.
  # As a rough guess, old = before 1998
  #
  # options       BKTR_NEW_MSP34XX_DRIVER
  # Use new, more complete initialization scheme for the msp34* soundchip.
  # Should fix stereo autodetection if the old driver does only output
  # mono sound.
  
  #
  # options       BKTR_USE_FREEBSD_SMBUS
  # Compile with FreeBSD SMBus implementation
  #
  # Brooktree driver has been ported to the new I2C framework. Thus,
  # you'll need to have the following 3 lines in the kernel config.
  #     device smbus
  #     device iicbus
  #     device iicbb
  #     device iicsmb
  # The iic and smb devices are only needed if you want to control other
  # I2C slaves connected to the external connector of some cards.
  #
  device          bktr
   
  #
  # PC Card/PCMCIA and Cardbus
  #
  # cbb: pci/cardbus bridge implementing YENTA interface
  # pccard: pccard slots
  # cardbus: cardbus slots
  device          cbb
  device          pccard
  device          cardbus
  
  #
  # MMC/SD
  #
  # mmc           MMC/SD bus
  # mmcsd         MMC/SD memory card
  # sdhci         Generic PCI SD Host Controller
  #
  device          mmc
  device          mmcsd
  device          sdhci
  
  #
  # SMB bus
  #
  # System Management Bus support is provided by the 'smbus' device.
  # Access to the SMBus device is via the 'smb' device (/dev/smb*),
  # which is a child of the 'smbus' device.
  #
  # Supported devices:
  # smb           standard I/O through /dev/smb*
  #
  # Supported SMB interfaces:
  # iicsmb        I2C to SMB bridge with any iicbus interface
  # bktr          brooktree848 I2C hardware interface
  # intpm         Intel PIIX4 (82371AB, 82443MX) Power Management Unit
  # alpm          Acer Aladdin-IV/V/Pro2 Power Management Unit
  # ichsmb        Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
  # viapm         VIA VT82C586B/596B/686A and VT8233 Power Management Unit
  # amdpm         AMD 756 Power Management Unit
  # amdsmb        AMD 8111 SMBus 2.0 Controller
  # nfpm          NVIDIA nForce Power Management Unit
  # nfsmb         NVIDIA nForce2/3/4 MCP SMBus 2.0 Controller
  #
  device          smbus           # Bus support, required for smb below.
  
  device          intpm
  device          alpm
  device          ichsmb
  device          viapm
  device          amdpm
  device          amdsmb
  device          nfpm
  device          nfsmb
  
  device          smb
  
  #
  # I2C Bus
  #
  # Philips i2c bus support is provided by the `iicbus' device.
  #
  # Supported devices:
  # ic    i2c network interface
  # iic   i2c standard io
  # iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
  # iicoc simple polling driver for OpenCores I2C controller
  #
  # Supported interfaces:
  # bktr  brooktree848 I2C software interface
  #
  # Other:
  # iicbb generic I2C bit-banging code (needed by lpbb, bktr)
  #
  device          iicbus          # Bus support, required for ic/iic/iicsmb below.
  device          iicbb
  
  device          ic
  device          iic
  device          iicsmb          # smb over i2c bridge
  device          iicoc           # OpenCores I2C controller support
  
  # I2C peripheral devices
  #
  # ds133x        Dallas Semiconductor DS1337, DS1338 and DS1339 RTC
  # ds1374        Dallas Semiconductor DS1374 RTC
  # ds1672        Dallas Semiconductor DS1672 RTC
  # s35390a       Seiko Instruments S-35390A RTC
  #
  device          ds133x
  device          ds1374
  device          ds1672
  device          s35390a
  
  # Parallel-Port Bus
  #
  # Parallel port bus support is provided by the `ppbus' device.
  # Multiple devices may be attached to the parallel port, devices
  # are automatically probed and attached when found.
  #
  # Supported devices:
  # vpo   Iomega Zip Drive
  #       Requires SCSI disk support ('scbus' and 'da'), best
  #       performance is achieved with ports in EPP 1.9 mode.
  # lpt   Parallel Printer
  # plip  Parallel network interface
  # ppi   General-purpose I/O ("Geek Port") + IEEE1284 I/O
  # pps   Pulse per second Timing Interface
  # lpbb  Philips official parallel port I2C bit-banging interface
  # pcfclock Parallel port clock driver.
  #
  # Supported interfaces:
  # ppc   ISA-bus parallel port interfaces.
  #
  
  options         PPC_PROBE_CHIPSET # Enable chipset specific detection
                                    # (see flags in ppc(4))
  options         DEBUG_1284      # IEEE1284 signaling protocol debug
  options         PERIPH_1284     # Makes your computer act as an IEEE1284
                                  # compliant peripheral
  options         DONTPROBE_1284  # Avoid boot detection of PnP parallel devices
  options         VP0_DEBUG       # ZIP/ZIP+ debug
  options         LPT_DEBUG       # Printer driver debug
  options         PPC_DEBUG       # Parallel chipset level debug
  options         PLIP_DEBUG      # Parallel network IP interface debug
  options         PCFCLOCK_VERBOSE         # Verbose pcfclock driver
  options         PCFCLOCK_MAX_RETRIES=5   # Maximum read tries (default 10)
  
  device          ppc
  hint.ppc.0.at="isa"
  hint.ppc.0.irq="7"
  device          ppbus
  device          vpo
  device          lpt
  device          plip
  device          ppi
  device          pps
  device          lpbb
  device          pcfclock
  
  # Kernel BOOTP support
  
  options         BOOTP           # Use BOOTP to obtain IP address/hostname
                                  # Requires NFSCLIENT and NFS_ROOT
  options         BOOTP_NFSROOT   # NFS mount root filesystem using BOOTP info
  options         BOOTP_NFSV3     # Use NFS v3 to NFS mount root
  options         BOOTP_COMPAT    # Workaround for broken bootp daemons.
  options         BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
  options         BOOTP_BLOCKSIZE=8192 # Override NFS block size
  
  #
  # Add software watchdog routines.
  #
  options         SW_WATCHDOG
  
  #
  # Add the software deadlock resolver thread.
  #
  options         DEADLKRES
  
  #
  # Disable swapping of stack pages.  This option removes all
  # code which actually performs swapping, so it's not possible to turn
  # it back on at run-time.
  #
  # This is sometimes usable for systems which don't have any swap space
  # (see also sysctls "vm.defer_swapspace_pageouts" and
  # "vm.disable_swapspace_pageouts")
  #
  #options        NO_SWAPPING
  
  # Set the number of sf_bufs to allocate. sf_bufs are virtual buffers
  # for sendfile(2) that are used to map file VM pages, and normally
  # default to a quantity that is roughly 16*MAXUSERS+512. You would
  # typically want about 4 of these for each simultaneous file send.
  #
  options         NSFBUFS=1024
  
  #
  # Enable extra debugging code for locks.  This stores the filename and
  # line of whatever acquired the lock in the lock itself, and changes a
  # number of function calls to pass around the relevant data.  This is
  # not at all useful unless you are debugging lock code.  Also note
  # that it is likely to break e.g. fstat(1) unless you recompile your
  # userland with -DDEBUG_LOCKS as well.
  #
  options         DEBUG_LOCKS
  
  
  #####################################################################
  # USB support
  # UHCI controller
  device          uhci
  # OHCI controller
  device          ohci
  # EHCI controller
  device          ehci
  # XHCI controller
  device          xhci
  # SL811 Controller
  #device         slhci
  # General USB code (mandatory for USB)
  device          usb
  #
  # USB Double Bulk Pipe devices
  device          udbp
  # USB Fm Radio
  device          ufm
  # Human Interface Device (anything with buttons and dials)
  device          uhid
  # USB keyboard
  device          ukbd
  # USB printer
  device          ulpt
  # USB mass storage driver (Requires scbus and da)
  device          umass
  # USB mass storage driver for device-side mode
  device          usfs
  # USB support for Belkin F5U109 and Magic Control Technology serial adapters
  device          umct
  # USB modem support
  device          umodem
  # USB mouse
  device          ums
  # eGalax USB touch screen
  device          uep
  # Diamond Rio 500 MP3 player
  device          urio
  #
  # USB serial support
  device          ucom
  # USB support for 3G modem cards by Option, Novatel, Huawei and Sierra
  device          u3g
  # USB support for Technologies ARK3116 based serial adapters
  device          uark
  # USB support for Belkin F5U103 and compatible serial adapters
  device          ubsa
  # USB support for serial adapters based on the FT8U100AX and FT8U232AM
  device          uftdi
  # USB support for some Windows CE based serial communication.
  device          uipaq
  # USB support for Prolific PL-2303 serial adapters
  device          uplcom
  # USB support for Silicon Laboratories CP2101/CP2102 based USB serial adapters
  device          uslcom
  # USB Visor and Palm devices
  device          uvisor
  # USB serial support for DDI pocket's PHS
  device          uvscom
  #
  # ADMtek USB ethernet. Supports the LinkSys USB100TX,
  # the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
  # and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
  # eval board.
  device          aue
  
  # ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
  # LinkSys USB200M and various other adapters.
  device          axe
  
  #
  # Devices which communicate using Ethernet over USB, particularly
  # Communication Device Class (CDC) Ethernet specification. Supports
  # Sharp Zaurus PDAs, some DOCSIS cable modems and so on.
  device          cdce
  #
  # CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
  # and Netmate II, and the Belkin F5U111.
  device          cue
  #
  # Kawasaki LSI ethernet. Supports the LinkSys USB10T,
  # Entrega USB-NET-E45, Peracom Ethernet Adapter, the
  # 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
  # the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
  # and 2104USB, and the Corega USB-T.
  device          kue
  #
  # RealTek RTL8150 USB to fast ethernet. Supports the Melco LUA-KTX
  # and the GREEN HOUSE GH-USB100B.
  device          rue
  #
  # Davicom DM9601E USB to fast ethernet. Supports the Corega FEther USB-TXC.
  device          udav
  #
  # Moschip MCS7730/MCS7840 USB to fast ethernet. Supports the Sitecom LN030.
  device          mos
  #
  # HSxPA devices from Option N.V
  device          uhso
  
  # Realtek RTL8188SU/RTL8191SU/RTL8192SU wireless driver
  device          rsu
  #
  # Ralink Technology RT2501USB/RT2601USB wireless driver
  device          rum
  # Ralink Technology RT2700U/RT2800U/RT3000U wireless driver
  device          run
  #
  # Atheros AR5523 wireless driver
  device          uath
  #
  # Conexant/Intersil PrismGT wireless driver
  device          upgt
  #
  # Ralink Technology RT2500USB wireless driver
  device          ural
  #
  # Realtek RTL8187B/L wireless driver
  device          urtw
  #
  # Realtek RTL8188CU/RTL8192CU wireless driver
  device          urtwn
  #
  # ZyDas ZD1211/ZD1211B wireless driver
  device          zyd
  #
  # Sierra USB wireless driver
  device          usie
  
  # 
  # debugging options for the USB subsystem
  #
  options         USB_DEBUG
  options         U3G_DEBUG
  
  # options for ukbd:
  options         UKBD_DFLT_KEYMAP        # specify the built-in keymap
  makeoptions     UKBD_DFLT_KEYMAP=it.iso
  
  # options for uplcom:
  options         UPLCOM_INTR_INTERVAL=100        # interrupt pipe interval
                                                  # in milliseconds
  
  # options for uvscom:
  options         UVSCOM_DEFAULT_OPKTSIZE=8       # default output packet size
  options         UVSCOM_INTR_INTERVAL=100        # interrupt pipe interval
                                                  # in milliseconds
  
  #####################################################################
  # FireWire support
  
  device          firewire        # FireWire bus code
  device          sbp             # SCSI over Firewire (Requires scbus and da)
  device          sbp_targ        # SBP-2 Target mode  (Requires scbus and targ)
  device          fwe             # Ethernet over FireWire (non-standard!)
  device          fwip            # IP over FireWire (RFC2734 and RFC3146)
  
  #####################################################################
  # dcons support (Dumb Console Device)
  
  device          dcons                   # dumb console driver
  device          dcons_crom              # FireWire attachment
  options         DCONS_BUF_SIZE=16384    # buffer size
  options         DCONS_POLL_HZ=100       # polling rate
  options         DCONS_FORCE_CONSOLE=0   # force to be the primary console
  options         DCONS_FORCE_GDB=1       # force to be the gdb device
  
  #####################################################################
  # crypto subsystem
  #
  # This is a port of the OpenBSD crypto framework.  Include this when
  # configuring IPSEC and when you have a h/w crypto device to accelerate
  # user applications that link to OpenSSL.
  #
  # Drivers are ports from OpenBSD with some simple enhancements that have
  # been fed back to OpenBSD.
  
  device          crypto          # core crypto support
  device          cryptodev       # /dev/crypto for access to h/w
  
  device          rndtest         # FIPS 140-2 entropy tester
  
  device          hifn            # Hifn 7951, 7781, etc.
  options         HIFN_DEBUG      # enable debugging support: hw.hifn.debug
  options         HIFN_RNDTEST    # enable rndtest support
  
  device          ubsec           # Broadcom 5501, 5601, 58xx
  options         UBSEC_DEBUG     # enable debugging support: hw.ubsec.debug
  options         UBSEC_RNDTEST   # enable rndtest support
  
  #####################################################################
  
  
  #
  # Embedded system options:
  #
  # An embedded system might want to run something other than init.
  options         INIT_PATH=/sbin/init:/rescue/init
  
  # Debug options
  options         BUS_DEBUG       # enable newbus debugging
  options         DEBUG_VFS_LOCKS # enable VFS lock debugging
  options         SOCKBUF_DEBUG   # enable sockbuf last record/mb tail checking
  
  #
  # Verbose SYSINIT
  #
  # Make the SYSINIT process performed by mi_startup() verbose.  This is very
  # useful when porting to a new architecture.  If DDB is also enabled, this
  # will print function names instead of addresses.
  options         VERBOSE_SYSINIT
  
  #####################################################################
  # SYSV IPC KERNEL PARAMETERS
  #
  # Maximum number of System V semaphores that can be used on the system at
  # one time.
  options         SEMMNI=11
  
  # Total number of semaphores system wide
  options         SEMMNS=61
  
  # Total number of undo structures in system
  options         SEMMNU=31
  
  # Maximum number of System V semaphores that can be used by a single process
  # at one time.
  options         SEMMSL=61
  
  # Maximum number of operations that can be outstanding on a single System V
  # semaphore at one time.
  options         SEMOPM=101
  
  # Maximum number of undo operations that can be outstanding on a single
  # System V semaphore at one time.
  options         SEMUME=11
  
  # Maximum number of shared memory pages system wide.
  options         SHMALL=1025
  
  # Maximum size, in bytes, of a single System V shared memory region.
  options         SHMMAX=(SHMMAXPGS*PAGE_SIZE+1)
  options         SHMMAXPGS=1025
  
  # Minimum size, in bytes, of a single System V shared memory region.
  options         SHMMIN=2
  
  # Maximum number of shared memory regions that can be used on the system
  # at one time.
  options         SHMMNI=33
  
  # Maximum number of System V shared memory regions that can be attached to
  # a single process at one time.
  options         SHMSEG=9
  
  # Compress user core dumps.
  options         COMPRESS_USER_CORES
  # required to compress file output from kernel for COMPRESS_USER_CORES.
  device          gzio        
  
  # Set the amount of time (in seconds) the system will wait before
  # rebooting automatically when a kernel panic occurs.  If set to (-1),
  # the system will wait indefinitely until a key is pressed on the
  # console.
  options         PANIC_REBOOT_WAIT_TIME=16
  
  # Attempt to bypass the buffer cache and put data directly into the
  # userland buffer for read operation when O_DIRECT flag is set on the
  # file.  Both offset and length of the read operation must be
  # multiples of the physical media sector size.
  #
  options         DIRECTIO
  
  # Specify a lower limit for the number of swap I/O buffers.  They are
  # (among other things) used when bypassing the buffer cache due to
  # DIRECTIO kernel option enabled and O_DIRECT flag set on file.
  #
  options         NSWBUF_MIN=120
  
  #####################################################################
  
  # More undocumented options for linting.
  # Note that documenting these is not considered an affront.
  
  options         CAM_DEBUG_DELAY
  
  # VFS cluster debugging.
  options         CLUSTERDEBUG
  
  options         DEBUG
  
  # Kernel filelock debugging.
  options         LOCKF_DEBUG
  
  # System V compatible message queues
  # Please note that the values provided here are used to test kernel
  # building.  The defaults in the sources provide almost the same numbers.
  # MSGSSZ must be a power of 2 between 8 and 1024.
  options         MSGMNB=2049     # Max number of chars in queue
  options         MSGMNI=41       # Max number of message queue identifiers
  options         MSGSEG=2049     # Max number of message segments
  options         MSGSSZ=16       # Size of a message segment
  options         MSGTQL=41       # Max number of messages in system
  
  options         NBUF=512        # Number of buffer headers
  
  options         SCSI_NCR_DEBUG
  options         SCSI_NCR_MAX_SYNC=10000
  options         SCSI_NCR_MAX_WIDE=1
  options         SCSI_NCR_MYADDR=7
  
  options         SC_DEBUG_LEVEL=5        # Syscons debug level
  options         SC_RENDER_DEBUG # syscons rendering debugging
  
  options         VFS_BIO_DEBUG   # VFS buffer I/O debugging
  
  options         KSTACK_MAX_PAGES=32 # Maximum pages to give the kernel stack
  
  # Adaptec Array Controller driver options
  options         AAC_DEBUG       # Debugging levels:
                                  # 0 - quiet, only emit warnings
                                  # 1 - noisy, emit major function
                                  #     points and things done
                                  # 2 - extremely noisy, emit trace
                                  #     items in loops, etc.
  
  # Resource Accounting
  options         RACCT
  
  # Resource Limits
  options         RCTL
  
  # Yet more undocumented options for linting.
  # BKTR_ALLOC_PAGES has no effect except to cause warnings, and
  # BROOKTREE_ALLOC_PAGES hasn't actually been superseded by it, since the
  # driver still mostly spells this option BROOKTREE_ALLOC_PAGES.
  ##options       BKTR_ALLOC_PAGES=(217*4+1)
  options         BROOKTREE_ALLOC_PAGES=(217*4+1)
  options         MAXFILES=999
  
  # Random number generator
  options         RANDOM_YARROW   # Yarrow RNG
  ##options       RANDOM_FORTUNA  # Fortuna RNG - not yet implemented
  options         RANDOM_DEBUG    # Debugging messages
  options         RANDOM_RWFILE   # Read and write entropy cache

Cache object: a6d8a2a8a4e0cefd7e72ad1f1d57133f