1 I2C for Atmel platforms
2
3 Required properties :
4 - compatible : Must be one of:
5 "atmel,at91rm9200-i2c",
6 "atmel,at91sam9261-i2c",
7 "atmel,at91sam9260-i2c",
8 "atmel,at91sam9g20-i2c",
9 "atmel,at91sam9g10-i2c",
10 "atmel,at91sam9x5-i2c",
11 "atmel,sama5d4-i2c",
12 "atmel,sama5d2-i2c",
13 "microchip,sam9x60-i2c".
14 - reg: physical base address of the controller and length of memory mapped
15 region.
16 - interrupts: interrupt number to the cpu.
17 - #address-cells = <1>;
18 - #size-cells = <0>;
19 - clocks: phandles to input clocks.
20
21 Optional properties:
22 - clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000
23 - dmas: A list of two dma specifiers, one for each entry in dma-names.
24 - dma-names: should contain "tx" and "rx".
25 - atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO
26 capable I2C controllers.
27 - i2c-sda-hold-time-ns: TWD hold time, only available for:
28 "atmel,sama5d4-i2c",
29 "atmel,sama5d2-i2c",
30 "microchip,sam9x60-i2c".
31 - scl-gpios: specify the gpio related to SCL pin
32 - sda-gpios: specify the gpio related to SDA pin
33 - pinctrl: add extra pinctrl to configure i2c pins to gpio function for i2c
34 bus recovery, call it "gpio" state
35 - Child nodes conforming to i2c bus binding
36
37
38 Examples :
39
40 i2c0: i2c@fff84000 {
41 compatible = "atmel,at91sam9g20-i2c";
42 reg = <0xfff84000 0x100>;
43 interrupts = <12 4 6>;
44 #address-cells = <1>;
45 #size-cells = <0>;
46 clocks = <&twi0_clk>;
47 clock-frequency = <400000>;
48
49 24c512@50 {
50 compatible = "atmel,24c512";
51 reg = <0x50>;
52 pagesize = <128>;
53 }
54 }
55
56 i2c0: i2c@f8034600 {
57 compatible = "atmel,sama5d2-i2c";
58 reg = <0xf8034600 0x100>;
59 interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
60 dmas = <&dma0
61 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
62 AT91_XDMAC_DT_PERID(11)>,
63 <&dma0
64 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
65 AT91_XDMAC_DT_PERID(12)>;
66 dma-names = "tx", "rx";
67 #address-cells = <1>;
68 #size-cells = <0>;
69 clocks = <&flx0>;
70 atmel,fifo-size = <16>;
71 i2c-sda-hold-time-ns = <336>;
72 pinctrl-names = "default", "gpio";
73 pinctrl-0 = <&pinctrl_i2c0>;
74 pinctrl-1 = <&pinctrl_i2c0_gpio>;
75 sda-gpios = <&pioA 30 GPIO_ACTIVE_HIGH>;
76 scl-gpios = <&pioA 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
77
78 wm8731: wm8731@1a {
79 compatible = "wm8731";
80 reg = <0x1a>;
81 };
82 };
Cache object: efaa7a32b7bd2fba3d295d9a96000078
|