ads7846.txt

Version: - FREEBSD - FREEBSD-13-STABLE - FREEBSD-13-0 - FREEBSD-12-STABLE - FREEBSD-12-0 - FREEBSD-11-STABLE - FREEBSD-11-0 - FREEBSD-10-STABLE - FREEBSD-10-0 - FREEBSD-9-STABLE - FREEBSD-9-0 - FREEBSD-8-STABLE - FREEBSD-8-0 - FREEBSD-7-STABLE - FREEBSD-7-0 - FREEBSD-6-STABLE - FREEBSD-6-0 - FREEBSD-5-STABLE - FREEBSD-5-0 - FREEBSD-4-STABLE - FREEBSD-3-STABLE - FREEBSD22 - l41 - OPENBSD - linux-2.6 - MK84 - PLAN9 - xnu-8792
SearchContext: - none - 3 - 10

    1 Device tree bindings for TI's ADS7843, ADS7845, ADS7846, ADS7873, TSC2046
    2 SPI driven touch screen controllers.
    3 
    4 The node for this driver must be a child node of a SPI controller, hence
    5 all mandatory properties described in
    6 
    7         Documentation/devicetree/bindings/spi/spi-bus.txt
    8 
    9 must be specified.
   10 
   11 Additional required properties:
   12 
   13         compatible              Must be one of the following, depending on the
   14                                 model:
   15                                         "ti,tsc2046"
   16                                         "ti,ads7843"
   17                                         "ti,ads7845"
   18                                         "ti,ads7846"
   19                                         "ti,ads7873"
   20 
   21         interrupts              An interrupt node describing the IRQ line the chip's
   22                                 !PENIRQ pin is connected to.
   23         vcc-supply              A regulator node for the supply voltage.
   24 
   25 
   26 Optional properties:
   27 
   28         ti,vref-delay-usecs             vref supply delay in usecs, 0 for
   29                                         external vref (u16).
   30         ti,vref-mv                      The VREF voltage, in millivolts (u16).
   31                                         Set to 0 to use internal references
   32                                         (ADS7846).
   33         ti,keep-vref-on                 set to keep vref on for differential
   34                                         measurements as well
   35         ti,settle-delay-usec            Settling time of the analog signals;
   36                                         a function of Vcc and the capacitance
   37                                         on the X/Y drivers.  If set to non-zero,
   38                                         two samples are taken with settle_delay
   39                                         us apart, and the second one is used.
   40                                         ~150 uSec with 0.01uF caps (u16).
   41         ti,penirq-recheck-delay-usecs   If set to non-zero, after samples are
   42                                         taken this delay is applied and penirq
   43                                         is rechecked, to help avoid false
   44                                         events.  This value is affected by the
   45                                         material used to build the touch layer
   46                                         (u16).
   47         ti,x-plate-ohms                 Resistance of the X-plate,
   48                                         in Ohms (u16).
   49         ti,y-plate-ohms                 Resistance of the Y-plate,
   50                                         in Ohms (u16).
   51         ti,x-min                        Minimum value on the X axis (u16).
   52         ti,y-min                        Minimum value on the Y axis (u16).
   53         ti,debounce-tol                 Tolerance used for filtering (u16).
   54         ti,debounce-rep                 Additional consecutive good readings
   55                                         required after the first two (u16).
   56         ti,pendown-gpio-debounce        Platform specific debounce time for the
   57                                         pendown-gpio (u32).
   58         pendown-gpio                    GPIO handle describing the pin the !PENIRQ
   59                                         line is connected to.
   60         wakeup-source                   use any event on touchscreen as wakeup event.
   61                                         (Legacy property support: "linux,wakeup")
   62         touchscreen-size-x              General touchscreen binding, see [1].
   63         touchscreen-size-y              General touchscreen binding, see [1].
   64         touchscreen-max-pressure        General touchscreen binding, see [1].
   65         touchscreen-min-pressure        General touchscreen binding, see [1].
   66         touchscreen-average-samples     General touchscreen binding, see [1].
   67         touchscreen-inverted-x          General touchscreen binding, see [1].
   68         touchscreen-inverted-y          General touchscreen binding, see [1].
   69         touchscreen-swapped-x-y         General touchscreen binding, see [1].
   70 
   71 [1] All general touchscreen properties are described in
   72     Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt.
   73 
   74 Deprecated properties:
   75 
   76         ti,swap-xy                      swap x and y axis
   77         ti,x-max                        Maximum value on the X axis (u16).
   78         ti,y-max                        Maximum value on the Y axis (u16).
   79         ti,pressure-min                 Minimum reported pressure value
   80                                         (threshold) - u16.
   81         ti,pressure-max                 Maximum reported pressure value (u16).
   82         ti,debounce-max                 Max number of additional readings per
   83                                         sample (u16).
   84 
   85 Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC::
   86 
   87         spi_controller {
   88                 tsc2046@0 {
   89                         reg = <0>;      /* CS0 */
   90                         compatible = "ti,tsc2046";
   91                         interrupt-parent = <&gpio1>;
   92                         interrupts = <8 0>;     /* BOOT6 / GPIO 8 */
   93                         spi-max-frequency = <1000000>;
   94                         pendown-gpio = <&gpio1 8 0>;
   95                         vcc-supply = <&reg_vcc3>;
   96 
   97                         ti,x-min = /bits/ 16 <0>;
   98                         ti,x-max = /bits/ 16 <8000>;
   99                         ti,y-min = /bits/ 16 <0>;
  100                         ti,y-max = /bits/ 16 <4800>;
  101                         ti,x-plate-ohms = /bits/ 16 <40>;
  102                         ti,pressure-max = /bits/ 16 <255>;
  103 
  104                         wakeup-source;
  105                 };
  106         };

Cache object: 6613e1e76da21de0350f6970ad29f981

[ source navigation ] [ diff markup ] [ identifier search ] [ freetext search ] [ file search ] [ list types ] [ track identifier ]

This page is part of the FreeBSD/Linux Linux Kernel Cross-Reference, and was automatically generated using a modified version of the LXR engine.

FreeBSD/Linux Kernel Cross Reference sys/contrib/device-tree/Bindings/input/touchscreen/ads7846.txt

FreeBSD/Linux Kernel Cross Reference
sys/contrib/device-tree/Bindings/input/touchscreen/ads7846.txt