FreeBSD/Linux Kernel Cross Reference
sys/contrib/device-tree/Bindings/mailbox/ti,omap-mailbox.yaml

     # SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause)
     %YAML 1.2
     ---
     $id: http://devicetree.org/schemas/mailbox/ti,omap-mailbox.yaml#
     $schema: http://devicetree.org/meta-schemas/core.yaml#
     
     title: TI OMAP2+ and K3 Mailbox devices
     
     maintainers:
      - Suman Anna <s-anna@ti.com>
    
    description: |
      The OMAP Mailbox hardware facilitates communication between different
      processors using a queued mailbox interrupt mechanism. The IP block is
      external to the various processor subsystems and is connected on an
      interconnect bus. The communication is achieved through a set of registers
      for message storage and interrupt configuration registers.
    
      Each mailbox IP block/cluster has a certain number of h/w fifo queues and
      output interrupt lines. An output interrupt line is routed to an interrupt
      controller within a processor subsystem, and there can be more than one line
      going to a specific processor's interrupt controller. The interrupt line
      connections are fixed for an instance and are dictated by the IP integration
      into the SoC (excluding the SoCs that have an Interrupt Crossbar or an
      Interrupt Router IP). Each interrupt line is programmable through a set of
      interrupt configuration registers, and have a rx and tx interrupt source per
      h/w fifo. Communication between different processors is achieved through the
      appropriate programming of the rx and tx interrupt sources on the appropriate
      interrupt lines.
    
      The number of h/w fifo queues and interrupt lines dictate the usable
      registers. All the current OMAP SoCs except for the newest DRA7xx SoC has a
      single IP instance. DRA7xx has multiple instances with different number of
      h/w fifo queues and interrupt lines between different instances. The interrupt
      lines can also be routed to different processor sub-systems on DRA7xx as they
      are routed through the Crossbar, a kind of interrupt router/multiplexer. The
      K3 AM65x, J721E and J7200 SoCs has each of these instances form a cluster and
      combine multiple clusters into a single IP block present within the Main
      NavSS. The interrupt lines from all these clusters are multiplexed and routed
      to different processor subsystems over a limited number of common interrupt
      output lines of an Interrupt Router. The AM64x SoCS also uses a single IP
      block comprising of multiple clusters, but the number of clusters are
      smaller, and the interrupt output lines are connected directly to various
      processors.
    
      Mailbox Controller Nodes
      =========================
      A Mailbox device node is used to represent a Mailbox IP instance/cluster
      within a SoC. The sub-mailboxes (actual communication channels) are
      represented as child nodes of this parent node.
    
      Mailbox Users
      ==============
      A device needing to communicate with a target processor device should specify
      them using the common mailbox binding properties, "mboxes" and the optional
      "mbox-names" (please see Documentation/devicetree/bindings/mailbox/mailbox.txt
      for details). Each value of the mboxes property should contain a phandle to
      the mailbox controller device node and an args specifier that will be the
      phandle to the intended sub-mailbox child node to be used for communication.
      The equivalent "mbox-names" property value can be used to give a name to the
      communication channel to be used by the client user.
    
    $defs:
      omap-mbox-descriptor:
        $ref: /schemas/types.yaml#/definitions/uint32-array
        description:
          The omap-mbox-descriptor is made of up of 3 cells and represents a single
          uni-directional communication channel. A typical sub-mailbox device uses
          two such channels - one for transmitting (Tx) and one for receiving (Rx).
        items:
          - description:
              mailbox fifo id used either for transmitting on ti,mbox-tx channel or
              for receiving on ti,mbox-rx channel (fifo_id). This is the hardware
              fifo number within a mailbox cluster.
          - description:
              irq identifier index number to use from the parent's interrupts data.
              Should be 0 for most of the cases, a positive index value is seen only
              on mailboxes that have multiple interrupt lines connected to the MPU
              processor (irq_id). This is an index number in the listed interrupts
              property in the DT nodes.
          - description:
              mailbox user id for identifying the interrupt line associated with
              generating a tx/rx fifo interrupt (usr_id). This is the hardware
              user id number within a mailbox cluster.
    
      omap-sub-mailbox:
        type: object
        description:
          The omap-sub-mailbox is a child node within a Mailbox controller device
          node and represents the actual communication channel used to send and
          receive messages between the host processor and a remote processor. Each
          child node should have a unique node name across all the different mailbox
          device nodes.
    
        properties:
          ti,mbox-tx:
            $ref: "#/$defs/omap-mbox-descriptor"
            description: sub-mailbox descriptor property defining a Tx fifo.
    
         ti,mbox-rx:
           $ref: "#/$defs/omap-mbox-descriptor"
           description: sub-mailbox descriptor property defining a Rx fifo.
   
         ti,mbox-send-noirq:
           type: boolean
           description:
             Quirk flag to allow the client user of this sub-mailbox to send
             messages without triggering a Tx ready interrupt, and to control
             the Tx ticker. Should be used only on sub-mailboxes used to
             communicate with WkupM3 remote processor on AM33xx/AM43xx SoCs.
   
       required:
         - ti,mbox-tx
         - ti,mbox-rx
   
   properties:
     compatible:
       enum:
         - ti,omap2-mailbox # for OMAP2420, OMAP2430 SoCs
         - ti,omap3-mailbox # for OMAP3430, OMAP3630 SoCs
         - ti,omap4-mailbox # for OMAP44xx, OMAP54xx, AM33xx, AM43xx and DRA7xx SoCs
         - ti,am654-mailbox # for K3 AM65x, J721E and J7200 SoCs
         - ti,am64-mailbox  # for K3 AM64x SoCs
   
     reg:
       maxItems: 1
   
     interrupts:
       description:
         Contains the interrupt information for the mailbox device. The format is
         dependent on which interrupt controller the Mailbox device uses. The
         number of interrupts listed will at most be the value specified in
         ti,mbox-num-users property, but is usually limited by the number of
         interrupts reaching the main processor. An interrupt-parent property
         is required on SoCs where the interrupt lines are connected through a
         Interrupt Router before reaching the main processor's GIC.
   
     "#mbox-cells":
       const: 1
       description:
         The specifier is a phandle to an omap-sub-mailbox device.
   
     ti,mbox-num-users:
       $ref: /schemas/types.yaml#/definitions/uint32
       description:
         Number of targets (processor devices) that the mailbox device can
         interrupt.
   
     ti,mbox-num-fifos:
       $ref: /schemas/types.yaml#/definitions/uint32
       description: Number of h/w fifo queues within the mailbox IP block.
   
     ti,hwmods:
       $ref: /schemas/types.yaml#/definitions/string
       deprecated: true
       description:
         Name of the hwmod associated with the mailbox. This should be defined
         in the mailbox node only if the node is not defined as a child node of
         a corresponding sysc interconnect node.
   
         This property is only needed on some legacy OMAP SoCs which have not
         yet been converted to the ti,sysc interconnect hierarachy, but is
         otherwise considered obsolete.
   
   patternProperties:
     "^mbox-[a-z0-9-]+$":
       $ref: "#/$defs/omap-sub-mailbox"
   
   required:
     - compatible
     - reg
     - interrupts
     - "#mbox-cells"
     - ti,mbox-num-users
     - ti,mbox-num-fifos
   
   allOf:
     - if:
         properties:
           compatible:
             enum:
               - ti,am654-mailbox
               - ti,am64-mailbox
       then:
         properties:
           ti,mbox-num-users:
             const: 4
           ti,mbox-num-fifos:
             const: 16
           interrupts:
             minItems: 1
             maxItems: 4
   
     - if:
         properties:
           compatible:
             enum:
               - ti,omap4-mailbox
       then:
         properties:
           ti,mbox-num-users:
             enum: [3, 4]
           ti,mbox-num-fifos:
             enum: [8, 12]
           interrupts:
             minItems: 1
             maxItems: 4
   
     - if:
         properties:
           compatible:
             enum:
               - ti,omap3-mailbox
       then:
         properties:
           ti,mbox-num-users:
             const: 2
           ti,mbox-num-fifos:
             const: 2
           interrupts:
             minItems: 1
             maxItems: 1
   
     - if:
         properties:
           compatible:
             enum:
               - ti,omap2-mailbox
       then:
         properties:
           ti,mbox-num-users:
             const: 4
           ti,mbox-num-fifos:
             const: 6
           interrupts:
             minItems: 1
             maxItems: 2
   
   additionalProperties: false
   
   examples:
     - |
       /* OMAP4 */
       #include <dt-bindings/interrupt-controller/arm-gic.h>
       mailbox: mailbox@4a0f4000 {
           compatible = "ti,omap4-mailbox";
           reg = <0x4a0f4000 0x200>;
           interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
           #mbox-cells = <1>;
           ti,mbox-num-users = <3>;
           ti,mbox-num-fifos = <8>;
   
           mbox_ipu: mbox-ipu {
               ti,mbox-tx = <0 0 0>;
               ti,mbox-rx = <1 0 0>;
           };
           mbox_dsp: mbox-dsp {
               ti,mbox-tx = <3 0 0>;
               ti,mbox-rx = <2 0 0>;
           };
       };
   
       dsp {
           mboxes = <&mailbox &mbox_dsp>;
       };
   
     - |
       /* AM33xx */
       mailbox1: mailbox@480c8000 {
           compatible = "ti,omap4-mailbox";
           reg = <0x480c8000 0x200>;
           interrupts = <77>;
           #mbox-cells = <1>;
           ti,mbox-num-users = <4>;
           ti,mbox-num-fifos = <8>;
   
           mbox_wkupm3: mbox-wkup-m3 {
               ti,mbox-tx = <0 0 0>;
               ti,mbox-rx = <0 0 3>;
               ti,mbox-send-noirq;
           };
       };
   
     - |
       /* AM65x */
       mailbox0_cluster0: mailbox@31f80000 {
           compatible = "ti,am654-mailbox";
           reg = <0x31f80000 0x200>;
           #mbox-cells = <1>;
           ti,mbox-num-users = <4>;
           ti,mbox-num-fifos = <16>;
           interrupt-parent = <&intr_main_navss>;
           interrupts = <436>;
   
           mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
               ti,mbox-tx = <1 0 0>;
               ti,mbox-rx = <0 0 0>;
           };
       };

Cache object: a048e7d61c2a4c12a8ca9bd9b390ed5f