qcom,ipq6018-pinctrl.yaml

Version: - FREEBSD - FREEBSD-13-STABLE - FREEBSD-13-0 - FREEBSD-12-STABLE - FREEBSD-12-0 - FREEBSD-11-STABLE - FREEBSD-11-0 - FREEBSD-10-STABLE - FREEBSD-10-0 - FREEBSD-9-STABLE - FREEBSD-9-0 - FREEBSD-8-STABLE - FREEBSD-8-0 - FREEBSD-7-STABLE - FREEBSD-7-0 - FREEBSD-6-STABLE - FREEBSD-6-0 - FREEBSD-5-STABLE - FREEBSD-5-0 - FREEBSD-4-STABLE - FREEBSD-3-STABLE - FREEBSD22 - l41 - OPENBSD - linux-2.6 - MK84 - PLAN9 - xnu-8792
SearchContext: - none - 3 - 10

    1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
    2 %YAML 1.2
    3 ---
    4 $id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
    5 $schema: http://devicetree.org/meta-schemas/core.yaml#
    6 
    7 title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
    8 
    9 maintainers:
   10   - Sricharan R <sricharan@codeaurora.org>
   11 
   12 description: |
   13   This binding describes the Top Level Mode Multiplexer block found in the
   14   IPQ6018 platform.
   15 
   16 properties:
   17   compatible:
   18     const: qcom,ipq6018-pinctrl
   19 
   20   reg:
   21     maxItems: 1
   22 
   23   interrupts:
   24     description: Specifies the TLMM summary IRQ
   25     maxItems: 1
   26 
   27   interrupt-controller: true
   28 
   29   '#interrupt-cells':
   30     description:
   31       Specifies the PIN numbers and Flags, as defined in defined in
   32       include/dt-bindings/interrupt-controller/irq.h
   33     const: 2
   34 
   35   gpio-controller: true
   36 
   37   '#gpio-cells':
   38     description: Specifying the pin number and flags, as defined in
   39       include/dt-bindings/gpio/gpio.h
   40     const: 2
   41 
   42   gpio-ranges:
   43     maxItems: 1
   44 
   45 #PIN CONFIGURATION NODES
   46 patternProperties:
   47   '-pinmux$':
   48     type: object
   49     description:
   50       Pinctrl node's client devices use subnodes for desired pin configuration.
   51       Client device subnodes use below standard properties.
   52     $ref: "/schemas/pinctrl/pincfg-node.yaml"
   53 
   54     properties:
   55       pins:
   56         description:
   57           List of gpio pins affected by the properties specified in this
   58           subnode.
   59         items:
   60           oneOf:
   61             - pattern: "^gpio([1-9]|[1-7][0-9]|80)$"
   62             - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd,
   63                       sdc2_data, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2,
   64                       qdsd_data3 ]
   65         minItems: 1
   66         maxItems: 4
   67 
   68       function:
   69         description:
   70           Specify the alternative function to be configured for the specified
   71           pins.
   72         enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
   73                 atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
   74                 atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
   75                 atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp1_i2c,
   76                 blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp6_i2c, blsp1_spi,
   77                 blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi,
   78                 blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi,
   79                 blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi,
   80                 blsp6_spi, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst,
   81                 cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
   82                 cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
   83                 dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
   84                 flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
   85                 gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
   86                 gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
   87                 ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
   88                 nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
   89                 pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
   90                 pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
   91                 pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
   92                 qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
   93                 qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
   94                 qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
   95                 qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
   96                 sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
   97                 uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
   98 
   99       drive-strength:
  100         enum: [2, 4, 6, 8, 10, 12, 14, 16]
  101         default: 2
  102         description:
  103           Selects the drive strength for the specified pins, in mA.
  104 
  105       bias-pull-down: true
  106 
  107       bias-pull-up: true
  108 
  109       bias-disable: true
  110 
  111       output-high: true
  112 
  113       output-low: true
  114 
  115     required:
  116       - pins
  117       - function
  118 
  119     additionalProperties: false
  120 
  121 allOf:
  122   - $ref: "pinctrl.yaml#"
  123 
  124 required:
  125   - compatible
  126   - reg
  127   - interrupts
  128   - interrupt-controller
  129   - '#interrupt-cells'
  130   - gpio-controller
  131   - '#gpio-cells'
  132   - gpio-ranges
  133 
  134 additionalProperties: false
  135 
  136 examples:
  137   - |
  138         #include <dt-bindings/interrupt-controller/arm-gic.h>
  139         tlmm: pinctrl@1000000 {
  140               compatible = "qcom,ipq6018-pinctrl";
  141               reg = <0x01000000 0x300000>;
  142               interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
  143               interrupt-controller;
  144               #interrupt-cells = <2>;
  145               gpio-controller;
  146               #gpio-cells = <2>;
  147               gpio-ranges = <&tlmm 0 0 80>;
  148 
  149               serial3-pinmux {
  150                       pins = "gpio44", "gpio45";
  151                       function = "blsp2_uart";
  152                       drive-strength = <8>;
  153                       bias-pull-down;
  154               };
  155         };

Cache object: e4f60ea8f7da5955874c040466b37aae

[ source navigation ] [ diff markup ] [ identifier search ] [ freetext search ] [ file search ] [ list types ] [ track identifier ]

This page is part of the FreeBSD/Linux Linux Kernel Cross-Reference, and was automatically generated using a modified version of the LXR engine.

FreeBSD/Linux Kernel Cross Reference sys/contrib/device-tree/Bindings/pinctrl/qcom,ipq6018-pinctrl.yaml

FreeBSD/Linux Kernel Cross Reference
sys/contrib/device-tree/Bindings/pinctrl/qcom,ipq6018-pinctrl.yaml