r8a7790-lager.dts

Version: - FREEBSD - FREEBSD-13-STABLE - FREEBSD-13-0 - FREEBSD-12-STABLE - FREEBSD-12-0 - FREEBSD-11-STABLE - FREEBSD-11-0 - FREEBSD-10-STABLE - FREEBSD-10-0 - FREEBSD-9-STABLE - FREEBSD-9-0 - FREEBSD-8-STABLE - FREEBSD-8-0 - FREEBSD-7-STABLE - FREEBSD-7-0 - FREEBSD-6-STABLE - FREEBSD-6-0 - FREEBSD-5-STABLE - FREEBSD-5-0 - FREEBSD-4-STABLE - FREEBSD-3-STABLE - FREEBSD22 - l41 - OPENBSD - linux-2.6 - MK84 - PLAN9 - xnu-8792
SearchContext: - none - 3 - 10
    1 // SPDX-License-Identifier: GPL-2.0
    2 /*
    3  * Device Tree Source for the Lager board
    4  *
    5  * Copyright (C) 2013-2014 Renesas Solutions Corp.
    6  * Copyright (C) 2014 Cogent Embedded, Inc.
    7  * Copyright (C) 2015-2016 Renesas Electronics Corporation
    8  */
    9 
   10 /*
   11  * SSI-AK4643
   12  *
   13  * SW1: 1: AK4643
   14  *      2: CN22
   15  *      3: ADV7511
   16  *
   17  * This command is required when Playback/Capture
   18  *
   19  *      amixer set "LINEOUT Mixer DACL" on
   20  *      amixer set "DVC Out" 100%
   21  *      amixer set "DVC In" 100%
   22  *
   23  * You can use Mute
   24  *
   25  *      amixer set "DVC Out Mute" on
   26  *      amixer set "DVC In Mute" on
   27  *
   28  * You can use Volume Ramp
   29  *
   30  *      amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
   31  *      amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
   32  *      amixer set "DVC Out Ramp" on
   33  *      aplay xxx.wav &
   34  *      amixer set "DVC Out"  80%  // Volume Down
   35  *      amixer set "DVC Out" 100%  // Volume Up
   36  */
   37 
   38 /dts-v1/;
   39 #include "r8a7790.dtsi"
   40 #include <dt-bindings/gpio/gpio.h>
   41 #include <dt-bindings/input/input.h>
   42 
   43 / {
   44         model = "Lager";
   45         compatible = "renesas,lager", "renesas,r8a7790";
   46 
   47         aliases {
   48                 serial0 = &scif0;
   49                 serial1 = &scifa1;
   50                 i2c8 = &gpioi2c1;
   51                 i2c9 = &gpioi2c2;
   52                 i2c10 = &i2cexio0;
   53                 i2c11 = &i2cexio1;
   54                 i2c12 = &i2chdmi;
   55                 i2c13 = &i2cpwr;
   56                 mmc0 = &mmcif1;
   57                 mmc1 = &sdhi0;
   58                 mmc2 = &sdhi2;
   59         };
   60 
   61         chosen {
   62                 bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
   63                 stdout-path = "serial0:115200n8";
   64         };
   65 
   66         memory@40000000 {
   67                 device_type = "memory";
   68                 reg = <0 0x40000000 0 0x40000000>;
   69         };
   70 
   71         memory@140000000 {
   72                 device_type = "memory";
   73                 reg = <1 0x40000000 0 0xc0000000>;
   74         };
   75 
   76         lbsc {
   77                 #address-cells = <1>;
   78                 #size-cells = <1>;
   79         };
   80 
   81         keyboard {
   82                 compatible = "gpio-keys";
   83 
   84                 pinctrl-0 = <&keyboard_pins>;
   85                 pinctrl-names = "default";
   86 
   87                 one {
   88                         linux,code = <KEY_1>;
   89                         label = "SW2-1";
   90                         wakeup-source;
   91                         debounce-interval = <20>;
   92                         gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
   93                 };
   94                 two {
   95                         linux,code = <KEY_2>;
   96                         label = "SW2-2";
   97                         wakeup-source;
   98                         debounce-interval = <20>;
   99                         gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
  100                 };
  101                 three {
  102                         linux,code = <KEY_3>;
  103                         label = "SW2-3";
  104                         wakeup-source;
  105                         debounce-interval = <20>;
  106                         gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
  107                 };
  108                 four {
  109                         linux,code = <KEY_4>;
  110                         label = "SW2-4";
  111                         wakeup-source;
  112                         debounce-interval = <20>;
  113                         gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
  114                 };
  115         };
  116 
  117         leds {
  118                 compatible = "gpio-leds";
  119                 led6 {
  120                         gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
  121                 };
  122                 led7 {
  123                         gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
  124                 };
  125                 led8 {
  126                         gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
  127                 };
  128         };
  129 
  130         fixedregulator3v3: regulator-3v3 {
  131                 compatible = "regulator-fixed";
  132                 regulator-name = "fixed-3.3V";
  133                 regulator-min-microvolt = <3300000>;
  134                 regulator-max-microvolt = <3300000>;
  135                 regulator-boot-on;
  136                 regulator-always-on;
  137         };
  138 
  139         vcc_sdhi0: regulator-vcc-sdhi0 {
  140                 compatible = "regulator-fixed";
  141 
  142                 regulator-name = "SDHI0 Vcc";
  143                 regulator-min-microvolt = <3300000>;
  144                 regulator-max-microvolt = <3300000>;
  145 
  146                 gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
  147                 enable-active-high;
  148         };
  149 
  150         vccq_sdhi0: regulator-vccq-sdhi0 {
  151                 compatible = "regulator-gpio";
  152 
  153                 regulator-name = "SDHI0 VccQ";
  154                 regulator-min-microvolt = <1800000>;
  155                 regulator-max-microvolt = <3300000>;
  156 
  157                 gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
  158                 gpios-states = <1>;
  159                 states = <3300000 1>, <1800000 0>;
  160         };
  161 
  162         vcc_sdhi2: regulator-vcc-sdhi2 {
  163                 compatible = "regulator-fixed";
  164 
  165                 regulator-name = "SDHI2 Vcc";
  166                 regulator-min-microvolt = <3300000>;
  167                 regulator-max-microvolt = <3300000>;
  168 
  169                 gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>;
  170                 enable-active-high;
  171         };
  172 
  173         vccq_sdhi2: regulator-vccq-sdhi2 {
  174                 compatible = "regulator-gpio";
  175 
  176                 regulator-name = "SDHI2 VccQ";
  177                 regulator-min-microvolt = <1800000>;
  178                 regulator-max-microvolt = <3300000>;
  179 
  180                 gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
  181                 gpios-states = <1>;
  182                 states = <3300000 1>, <1800000 0>;
  183         };
  184 
  185         audio_clock: audio_clock {
  186                 compatible = "fixed-clock";
  187                 #clock-cells = <0>;
  188                 clock-frequency = <11289600>;
  189         };
  190 
  191         rsnd_ak4643: sound {
  192                 compatible = "simple-audio-card";
  193 
  194                 simple-audio-card,format = "left_j";
  195                 simple-audio-card,bitclock-master = <&sndcodec>;
  196                 simple-audio-card,frame-master = <&sndcodec>;
  197 
  198                 sndcpu: simple-audio-card,cpu {
  199                         sound-dai = <&rcar_sound>;
  200                 };
  201 
  202                 sndcodec: simple-audio-card,codec {
  203                         sound-dai = <&ak4643>;
  204                         clocks = <&audio_clock>;
  205                 };
  206         };
  207 
  208         vga-encoder {
  209                 compatible = "adi,adv7123";
  210 
  211                 ports {
  212                         #address-cells = <1>;
  213                         #size-cells = <0>;
  214 
  215                         port@0 {
  216                                 reg = <0>;
  217                                 adv7123_in: endpoint {
  218                                         remote-endpoint = <&du_out_rgb>;
  219                                 };
  220                         };
  221                         port@1 {
  222                                 reg = <1>;
  223                                 adv7123_out: endpoint {
  224                                         remote-endpoint = <&vga_in>;
  225                                 };
  226                         };
  227                 };
  228         };
  229 
  230         vga {
  231                 compatible = "vga-connector";
  232 
  233                 port {
  234                         vga_in: endpoint {
  235                                 remote-endpoint = <&adv7123_out>;
  236                         };
  237                 };
  238         };
  239 
  240         hdmi-in {
  241                 compatible = "hdmi-connector";
  242                 type = "a";
  243 
  244                 port {
  245                         hdmi_con_in: endpoint {
  246                                 remote-endpoint = <&adv7612_in>;
  247                         };
  248                 };
  249         };
  250 
  251         cec_clock: cec-clock {
  252                 compatible = "fixed-clock";
  253                 #clock-cells = <0>;
  254                 clock-frequency = <12000000>;
  255         };
  256 
  257         hdmi-out {
  258                 compatible = "hdmi-connector";
  259                 type = "a";
  260 
  261                 port {
  262                         hdmi_con_out: endpoint {
  263                                 remote-endpoint = <&adv7511_out>;
  264                         };
  265                 };
  266         };
  267 
  268         x2_clk: x2-clock {
  269                 compatible = "fixed-clock";
  270                 #clock-cells = <0>;
  271                 clock-frequency = <148500000>;
  272         };
  273 
  274         x13_clk: x13-clock {
  275                 compatible = "fixed-clock";
  276                 #clock-cells = <0>;
  277                 clock-frequency = <148500000>;
  278         };
  279 
  280         gpioi2c1: i2c-8 {
  281                 #address-cells = <1>;
  282                 #size-cells = <0>;
  283                 compatible = "i2c-gpio";
  284                 status = "disabled";
  285                 scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  286                 sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  287                 i2c-gpio,delay-us = <5>;
  288         };
  289 
  290         gpioi2c2: i2c-9 {
  291                 #address-cells = <1>;
  292                 #size-cells = <0>;
  293                 compatible = "i2c-gpio";
  294                 status = "disabled";
  295                 scl-gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  296                 sda-gpios = <&gpio5 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  297                 i2c-gpio,delay-us = <5>;
  298         };
  299 
  300         /*
  301          * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
  302          * We use the I2C demuxer, so the desired IP core can be selected at runtime
  303          * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0).
  304          * Note: For testing the I2C slave feature, it is convenient to connect this
  305          * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
  306          * instantiate the slave device at runtime according to the documentation.
  307          * You can then communicate with the slave via IIC3.
  308          *
  309          * IIC0/I2C0 does not appear to support fallback to GPIO.
  310          */
  311         i2cexio0: i2c-10 {
  312                 compatible = "i2c-demux-pinctrl";
  313                 i2c-parent = <&iic0>, <&i2c0>;
  314                 i2c-bus-name = "i2c-exio0";
  315                 #address-cells = <1>;
  316                 #size-cells = <0>;
  317         };
  318 
  319         /*
  320          * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
  321          * This is similar to the arangement described for i2cexio0 (above)
  322          * with a fallback to GPIO also provided.
  323          */
  324         i2cexio1: i2c-11 {
  325                 compatible = "i2c-demux-pinctrl";
  326                 i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
  327                 i2c-bus-name = "i2c-exio1";
  328                 #address-cells = <1>;
  329                 #size-cells = <0>;
  330         };
  331 
  332         /*
  333          * IIC2 and I2C2 may be switched using pinmux.
  334          * A fallback to GPIO is also provided.
  335          */
  336         i2chdmi: i2c-12 {
  337                 compatible = "i2c-demux-pinctrl";
  338                 i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
  339                 i2c-bus-name = "i2c-hdmi";
  340                 #address-cells = <1>;
  341                 #size-cells = <0>;
  342 
  343                 ak4643: codec@12 {
  344                         compatible = "asahi-kasei,ak4643";
  345                         #sound-dai-cells = <0>;
  346                         reg = <0x12>;
  347                 };
  348 
  349                 composite-in@20 {
  350                         compatible = "adi,adv7180";
  351                         reg = <0x20>;
  352 
  353                         port {
  354                                 adv7180: endpoint {
  355                                         bus-width = <8>;
  356                                         remote-endpoint = <&vin1ep0>;
  357                                 };
  358                         };
  359                 };
  360 
  361                 hdmi@39 {
  362                         compatible = "adi,adv7511w";
  363                         reg = <0x39>;
  364                         interrupt-parent = <&gpio1>;
  365                         interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
  366                         clocks = <&cec_clock>;
  367                         clock-names = "cec";
  368 
  369                         adi,input-depth = <8>;
  370                         adi,input-colorspace = "rgb";
  371                         adi,input-clock = "1x";
  372 
  373                         ports {
  374                                 #address-cells = <1>;
  375                                 #size-cells = <0>;
  376 
  377                                 port@0 {
  378                                         reg = <0>;
  379                                         adv7511_in: endpoint {
  380                                                 remote-endpoint = <&lvds0_out>;
  381                                         };
  382                                 };
  383 
  384                                 port@1 {
  385                                         reg = <1>;
  386                                         adv7511_out: endpoint {
  387                                                 remote-endpoint = <&hdmi_con_out>;
  388                                         };
  389                                 };
  390                         };
  391                 };
  392 
  393                 hdmi-in@4c {
  394                         compatible = "adi,adv7612";
  395                         reg = <0x4c>;
  396                         interrupt-parent = <&gpio1>;
  397                         interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
  398                         default-input = <0>;
  399 
  400                         ports {
  401                                 #address-cells = <1>;
  402                                 #size-cells = <0>;
  403 
  404                                 port@0 {
  405                                         reg = <0>;
  406                                         adv7612_in: endpoint {
  407                                                 remote-endpoint = <&hdmi_con_in>;
  408                                         };
  409                                 };
  410 
  411                                 port@2 {
  412                                         reg = <2>;
  413                                         adv7612_out: endpoint {
  414                                                 remote-endpoint = <&vin0ep2>;
  415                                         };
  416                                 };
  417                         };
  418                 };
  419         };
  420 
  421         /*
  422          * IIC3 and I2C3 may be switched using pinmux.
  423          * IIC3/I2C3 does not appear to support fallback to GPIO.
  424          */
  425         i2cpwr: i2c-13 {
  426                 compatible = "i2c-demux-pinctrl";
  427                 pinctrl-names = "default";
  428                 pinctrl-0 = <&pmic_irq_pins>;
  429                 i2c-parent = <&iic3>, <&i2c3>;
  430                 i2c-bus-name = "i2c-pwr";
  431                 #address-cells = <1>;
  432                 #size-cells = <0>;
  433 
  434                 pmic@58 {
  435                         compatible = "dlg,da9063";
  436                         reg = <0x58>;
  437                         interrupt-parent = <&irqc0>;
  438                         interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
  439                         interrupt-controller;
  440 
  441                         rtc {
  442                                 compatible = "dlg,da9063-rtc";
  443                         };
  444 
  445                         watchdog {
  446                                 compatible = "dlg,da9063-watchdog";
  447                         };
  448                 };
  449 
  450                 vdd_dvfs: regulator@68 {
  451                         compatible = "dlg,da9210";
  452                         reg = <0x68>;
  453                         interrupt-parent = <&irqc0>;
  454                         interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
  455 
  456                         regulator-min-microvolt = <1000000>;
  457                         regulator-max-microvolt = <1000000>;
  458                         regulator-boot-on;
  459                         regulator-always-on;
  460                 };
  461         };
  462 };
  463 
  464 &du {
  465         pinctrl-0 = <&du_pins>;
  466         pinctrl-names = "default";
  467         status = "okay";
  468 
  469         clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
  470                  <&x13_clk>, <&x2_clk>;
  471         clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1";
  472 
  473         ports {
  474                 port@0 {
  475                         endpoint {
  476                                 remote-endpoint = <&adv7123_in>;
  477                         };
  478                 };
  479         };
  480 };
  481 
  482 &lvds0 {
  483         status = "okay";
  484 
  485         ports {
  486                 port@1 {
  487                         endpoint {
  488                                 remote-endpoint = <&adv7511_in>;
  489                         };
  490                 };
  491         };
  492 };
  493 
  494 &lvds1 {
  495         ports {
  496                 port@1 {
  497                         lvds_connector: endpoint {
  498                         };
  499                 };
  500         };
  501 };
  502 
  503 &extal_clk {
  504         clock-frequency = <20000000>;
  505 };
  506 
  507 &pfc {
  508         pinctrl-0 = <&scif_clk_pins>;
  509         pinctrl-names = "default";
  510 
  511         du_pins: du {
  512                 groups = "du_rgb666", "du_sync_1", "du_clk_out_0";
  513                 function = "du";
  514         };
  515 
  516         scif0_pins: scif0 {
  517                 groups = "scif0_data";
  518                 function = "scif0";
  519         };
  520 
  521         scif_clk_pins: scif_clk {
  522                 groups = "scif_clk";
  523                 function = "scif_clk";
  524         };
  525 
  526         ether_pins: ether {
  527                 groups = "eth_link", "eth_mdio", "eth_rmii";
  528                 function = "eth";
  529         };
  530 
  531         phy1_pins: phy1 {
  532                 groups = "intc_irq0";
  533                 function = "intc";
  534         };
  535 
  536         scifa1_pins: scifa1 {
  537                 groups = "scifa1_data";
  538                 function = "scifa1";
  539         };
  540 
  541         sdhi0_pins: sd0 {
  542                 groups = "sdhi0_data4", "sdhi0_ctrl";
  543                 function = "sdhi0";
  544                 power-source = <3300>;
  545         };
  546 
  547         sdhi0_pins_uhs: sd0_uhs {
  548                 groups = "sdhi0_data4", "sdhi0_ctrl";
  549                 function = "sdhi0";
  550                 power-source = <1800>;
  551         };
  552 
  553         sdhi2_pins: sd2 {
  554                 groups = "sdhi2_data4", "sdhi2_ctrl";
  555                 function = "sdhi2";
  556                 power-source = <3300>;
  557         };
  558 
  559         sdhi2_pins_uhs: sd2_uhs {
  560                 groups = "sdhi2_data4", "sdhi2_ctrl";
  561                 function = "sdhi2";
  562                 power-source = <1800>;
  563         };
  564 
  565         mmc1_pins: mmc1 {
  566                 groups = "mmc1_data8", "mmc1_ctrl";
  567                 function = "mmc1";
  568         };
  569 
  570         qspi_pins: qspi {
  571                 groups = "qspi_ctrl", "qspi_data4";
  572                 function = "qspi";
  573         };
  574 
  575         msiof1_pins: msiof1 {
  576                 groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
  577                                  "msiof1_tx";
  578                 function = "msiof1";
  579         };
  580 
  581         i2c0_pins: i2c0 {
  582                 groups = "i2c0";
  583                 function = "i2c0";
  584         };
  585 
  586         iic0_pins: iic0 {
  587                 groups = "iic0";
  588                 function = "iic0";
  589         };
  590 
  591         i2c1_pins: i2c1 {
  592                 groups = "i2c1";
  593                 function = "i2c1";
  594         };
  595 
  596         iic1_pins: iic1 {
  597                 groups = "iic1";
  598                 function = "iic1";
  599         };
  600 
  601         i2c2_pins: i2c2 {
  602                 groups = "i2c2";
  603                 function = "i2c2";
  604         };
  605 
  606         iic2_pins: iic2 {
  607                 groups = "iic2";
  608                 function = "iic2";
  609         };
  610 
  611         i2c3_pins: i2c3 {
  612                 groups = "i2c3";
  613                 function = "i2c3";
  614         };
  615 
  616         iic3_pins: iic3 {
  617                 groups = "iic3";
  618                 function = "iic3";
  619         };
  620 
  621         pmic_irq_pins: pmicirq {
  622                 groups = "intc_irq2";
  623                 function = "intc";
  624         };
  625 
  626         hsusb_pins: hsusb {
  627                 groups = "usb0_ovc_vbus";
  628                 function = "usb0";
  629         };
  630 
  631         usb0_pins: usb0 {
  632                 groups = "usb0";
  633                 function = "usb0";
  634         };
  635 
  636         usb1_pins: usb1 {
  637                 groups = "usb1";
  638                 function = "usb1";
  639         };
  640 
  641         usb2_pins: usb2 {
  642                 groups = "usb2";
  643                 function = "usb2";
  644         };
  645 
  646         vin0_pins: vin0 {
  647                 groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
  648                 function = "vin0";
  649         };
  650 
  651         vin1_pins: vin1 {
  652                 groups = "vin1_data8", "vin1_clk";
  653                 function = "vin1";
  654         };
  655 
  656         sound_pins: sound {
  657                 groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
  658                 function = "ssi";
  659         };
  660 
  661         sound_clk_pins: sound_clk {
  662                 groups = "audio_clk_a";
  663                 function = "audio_clk";
  664         };
  665 
  666         keyboard_pins: keyboard {
  667                 pins = "GP_1_14", "GP_1_24", "GP_1_26", "GP_1_28";
  668                 bias-pull-up;
  669         };
  670 };
  671 
  672 &ether {
  673         pinctrl-0 = <&ether_pins>, <&phy1_pins>;
  674         pinctrl-names = "default";
  675 
  676         phy-handle = <&phy1>;
  677         renesas,ether-link-active-low;
  678         status = "okay";
  679 
  680         phy1: ethernet-phy@1 {
  681                 compatible = "ethernet-phy-id0022.1537",
  682                              "ethernet-phy-ieee802.3-c22";
  683                 reg = <1>;
  684                 interrupt-parent = <&irqc0>;
  685                 interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
  686                 micrel,led-mode = <1>;
  687                 reset-gpios = <&gpio5 31 GPIO_ACTIVE_LOW>;
  688         };
  689 };
  690 
  691 &cmt0 {
  692         status = "okay";
  693 };
  694 
  695 &mmcif1 {
  696         pinctrl-0 = <&mmc1_pins>;
  697         pinctrl-names = "default";
  698 
  699         vmmc-supply = <&fixedregulator3v3>;
  700         bus-width = <8>;
  701         non-removable;
  702         status = "okay";
  703 };
  704 
  705 &sata1 {
  706         status = "okay";
  707 };
  708 
  709 &qspi {
  710         pinctrl-0 = <&qspi_pins>;
  711         pinctrl-names = "default";
  712 
  713         status = "okay";
  714 
  715         flash: flash@0 {
  716                 compatible = "spansion,s25fl512s", "jedec,spi-nor";
  717                 reg = <0>;
  718                 spi-max-frequency = <30000000>;
  719                 spi-tx-bus-width = <4>;
  720                 spi-rx-bus-width = <4>;
  721                 spi-cpha;
  722                 spi-cpol;
  723                 m25p,fast-read;
  724 
  725                 partitions {
  726                         compatible = "fixed-partitions";
  727                         #address-cells = <1>;
  728                         #size-cells = <1>;
  729 
  730                         partition@0 {
  731                                 label = "loader";
  732                                 reg = <0x00000000 0x00040000>;
  733                                 read-only;
  734                         };
  735                         partition@40000 {
  736                                 label = "user";
  737                                 reg = <0x00040000 0x00400000>;
  738                                 read-only;
  739                         };
  740                         partition@440000 {
  741                                 label = "flash";
  742                                 reg = <0x00440000 0x03bc0000>;
  743                         };
  744                 };
  745         };
  746 };
  747 
  748 &scif0 {
  749         pinctrl-0 = <&scif0_pins>;
  750         pinctrl-names = "default";
  751 
  752         status = "okay";
  753 };
  754 
  755 &scifa1 {
  756         pinctrl-0 = <&scifa1_pins>;
  757         pinctrl-names = "default";
  758 
  759         status = "okay";
  760 };
  761 
  762 &scif_clk {
  763         clock-frequency = <14745600>;
  764 };
  765 
  766 &msiof1 {
  767         pinctrl-0 = <&msiof1_pins>;
  768         pinctrl-names = "default";
  769 
  770         status = "okay";
  771 
  772         pmic: pmic@0 {
  773                 compatible = "renesas,r2a11302ft";
  774                 reg = <0>;
  775                 spi-max-frequency = <6000000>;
  776                 spi-cpol;
  777                 spi-cpha;
  778         };
  779 };
  780 
  781 &sdhi0 {
  782         pinctrl-0 = <&sdhi0_pins>;
  783         pinctrl-1 = <&sdhi0_pins_uhs>;
  784         pinctrl-names = "default", "state_uhs";
  785 
  786         vmmc-supply = <&vcc_sdhi0>;
  787         vqmmc-supply = <&vccq_sdhi0>;
  788         cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
  789         sd-uhs-sdr50;
  790         sd-uhs-sdr104;
  791         status = "okay";
  792 };
  793 
  794 &sdhi2 {
  795         pinctrl-0 = <&sdhi2_pins>;
  796         pinctrl-1 = <&sdhi2_pins_uhs>;
  797         pinctrl-names = "default", "state_uhs";
  798 
  799         vmmc-supply = <&vcc_sdhi2>;
  800         vqmmc-supply = <&vccq_sdhi2>;
  801         cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
  802         sd-uhs-sdr50;
  803         status = "okay";
  804 };
  805 
  806 &cpu0 {
  807         cpu0-supply = <&vdd_dvfs>;
  808 };
  809 
  810 &i2c0   {
  811         pinctrl-0 = <&i2c0_pins>;
  812         pinctrl-names = "i2c-exio0";
  813 };
  814 
  815 &iic0   {
  816         pinctrl-0 = <&iic0_pins>;
  817         pinctrl-names = "i2c-exio0";
  818 };
  819 
  820 &i2c1   {
  821         pinctrl-0 = <&i2c1_pins>;
  822         pinctrl-names = "i2c-exio1";
  823 };
  824 
  825 &iic1   {
  826         pinctrl-0 = <&iic1_pins>;
  827         pinctrl-names = "i2c-exio1";
  828 };
  829 
  830 &i2c2   {
  831         pinctrl-0 = <&i2c2_pins>;
  832         pinctrl-names = "i2c-hdmi";
  833 
  834         clock-frequency = <100000>;
  835 };
  836 
  837 &iic2   {
  838         pinctrl-0 = <&iic2_pins>;
  839         pinctrl-names = "i2c-hdmi";
  840 
  841         clock-frequency = <100000>;
  842 };
  843 
  844 &i2c3   {
  845         pinctrl-0 = <&i2c3_pins>;
  846         pinctrl-names = "i2c-pwr";
  847 };
  848 
  849 &iic3   {
  850         pinctrl-0 = <&iic3_pins>;
  851         pinctrl-names = "i2c-pwr";
  852 };
  853 
  854 &pci0 {
  855         status = "okay";
  856         pinctrl-0 = <&usb0_pins>;
  857         pinctrl-names = "default";
  858 };
  859 
  860 &pci1 {
  861         status = "okay";
  862         pinctrl-0 = <&usb1_pins>;
  863         pinctrl-names = "default";
  864 };
  865 
  866 &xhci {
  867         status = "okay";
  868         pinctrl-0 = <&usb2_pins>;
  869         pinctrl-names = "default";
  870 };
  871 
  872 &pci2 {
  873         status = "okay";
  874         pinctrl-0 = <&usb2_pins>;
  875         pinctrl-names = "default";
  876 };
  877 
  878 &hsusb {
  879         status = "okay";
  880         pinctrl-0 = <&hsusb_pins>;
  881         pinctrl-names = "default";
  882         renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>;
  883 };
  884 
  885 &usbphy {
  886         status = "okay";
  887 };
  888 
  889 /* HDMI video input */
  890 &vin0 {
  891         pinctrl-0 = <&vin0_pins>;
  892         pinctrl-names = "default";
  893 
  894         status = "okay";
  895 
  896         port {
  897                 vin0ep2: endpoint {
  898                         remote-endpoint = <&adv7612_out>;
  899                         bus-width = <24>;
  900                         hsync-active = <0>;
  901                         vsync-active = <0>;
  902                         pclk-sample = <1>;
  903                         data-active = <1>;
  904                 };
  905         };
  906 };
  907 
  908 /* composite video input */
  909 &vin1 {
  910         pinctrl-0 = <&vin1_pins>;
  911         pinctrl-names = "default";
  912 
  913         status = "okay";
  914 
  915         port {
  916                 vin1ep0: endpoint {
  917                         remote-endpoint = <&adv7180>;
  918                         bus-width = <8>;
  919                 };
  920         };
  921 };
  922 
  923 &rcar_sound {
  924         pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
  925         pinctrl-names = "default";
  926 
  927         /* Single DAI */
  928         #sound-dai-cells = <0>;
  929 
  930         status = "okay";
  931 
  932         rcar_sound,dai {
  933                 dai0 {
  934                         playback = <&ssi0>, <&src2>, <&dvc0>;
  935                         capture  = <&ssi1>, <&src3>, <&dvc1>;
  936                 };
  937         };
  938 };
  939 
  940 &rwdt {
  941         timeout-sec = <60>;
  942         status = "okay";
  943 };
  944 
  945 &ssi1 {
  946         shared-pin;
  947 };
Cache object: 1243c4d1db2c93298399c165bfed30e2
[ source navigation ] [ diff markup ] [ identifier search ] [ freetext search ] [ file search ] [ list types ] [ track identifier ]
This page is part of the FreeBSD/Linux Linux Kernel Cross-Reference, and was automatically generated using a modified version of the LXR engine.
FreeBSD/Linux Kernel Cross Reference sys/contrib/device-tree/src/arm/r8a7790-lager.dts

FreeBSD/Linux Kernel Cross Reference
sys/contrib/device-tree/src/arm/r8a7790-lager.dts
