Now available: The Design and Implementation of the FreeBSD Operating System (Second Edition)
[ source navigation ] [ diff markup ] [ identifier search ] [ freetext search ] [ file search ] [ list types ] [ track identifier ]
FreeBSD/Linux Kernel Cross Reference
sys/dev/e1000/e1000_82541.c
Version:
- FREEBSD - FREEBSD-13-STABLE - FREEBSD-13-0 - FREEBSD-12-STABLE - FREEBSD-12-0 - FREEBSD-11-STABLE - FREEBSD-11-0 - FREEBSD-10-STABLE - FREEBSD-10-0 - FREEBSD-9-STABLE - FREEBSD-9-0 - FREEBSD-8-STABLE - FREEBSD-8-0 - FREEBSD-7-STABLE - FREEBSD-7-0 - FREEBSD-6-STABLE - FREEBSD-6-0 - FREEBSD-5-STABLE - FREEBSD-5-0 - FREEBSD-4-STABLE - FREEBSD-3-STABLE - FREEBSD22 - l41 - OPENBSD - linux-2.6 - MK84 - PLAN9 - xnu-8792
SearchContext: - none - 3 - 10
SearchContext: - none - 3 - 10
1 /****************************************************************************** 2 3 Copyright (c) 2001-2011, Intel Corporation 4 All rights reserved. 5 6 Redistribution and use in source and binary forms, with or without 7 modification, are permitted provided that the following conditions are met: 8 9 1. Redistributions of source code must retain the above copyright notice, 10 this list of conditions and the following disclaimer. 11 12 2. Redistributions in binary form must reproduce the above copyright 13 notice, this list of conditions and the following disclaimer in the 14 documentation and/or other materials provided with the distribution. 15 16 3. Neither the name of the Intel Corporation nor the names of its 17 contributors may be used to endorse or promote products derived from 18 this software without specific prior written permission. 19 20 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 21 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 24 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 30 POSSIBILITY OF SUCH DAMAGE. 31 32 ******************************************************************************/ 33 /*$FreeBSD$*/ 34 35 /* 36 * 82541EI Gigabit Ethernet Controller 37 * 82541ER Gigabit Ethernet Controller 38 * 82541GI Gigabit Ethernet Controller 39 * 82541PI Gigabit Ethernet Controller 40 * 82547EI Gigabit Ethernet Controller 41 * 82547GI Gigabit Ethernet Controller 42 */ 43 44 #include "e1000_api.h" 45 46 static s32 e1000_init_phy_params_82541(struct e1000_hw *hw); 47 static s32 e1000_init_nvm_params_82541(struct e1000_hw *hw); 48 static s32 e1000_init_mac_params_82541(struct e1000_hw *hw); 49 static s32 e1000_reset_hw_82541(struct e1000_hw *hw); 50 static s32 e1000_init_hw_82541(struct e1000_hw *hw); 51 static s32 e1000_get_link_up_info_82541(struct e1000_hw *hw, u16 *speed, 52 u16 *duplex); 53 static s32 e1000_phy_hw_reset_82541(struct e1000_hw *hw); 54 static s32 e1000_setup_copper_link_82541(struct e1000_hw *hw); 55 static s32 e1000_check_for_link_82541(struct e1000_hw *hw); 56 static s32 e1000_get_cable_length_igp_82541(struct e1000_hw *hw); 57 static s32 e1000_set_d3_lplu_state_82541(struct e1000_hw *hw, 58 bool active); 59 static s32 e1000_setup_led_82541(struct e1000_hw *hw); 60 static s32 e1000_cleanup_led_82541(struct e1000_hw *hw); 61 static void e1000_clear_hw_cntrs_82541(struct e1000_hw *hw); 62 static s32 e1000_read_mac_addr_82541(struct e1000_hw *hw); 63 static s32 e1000_config_dsp_after_link_change_82541(struct e1000_hw *hw, 64 bool link_up); 65 static s32 e1000_phy_init_script_82541(struct e1000_hw *hw); 66 static void e1000_power_down_phy_copper_82541(struct e1000_hw *hw); 67 68 static const u16 e1000_igp_cable_length_table[] = 69 { 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 70 5, 10, 10, 10, 10, 10, 10, 10, 20, 20, 20, 20, 20, 25, 25, 25, 71 25, 25, 25, 25, 30, 30, 30, 30, 40, 40, 40, 40, 40, 40, 40, 40, 72 40, 50, 50, 50, 50, 50, 50, 50, 60, 60, 60, 60, 60, 60, 60, 60, 73 60, 70, 70, 70, 70, 70, 70, 80, 80, 80, 80, 80, 80, 90, 90, 90, 74 90, 90, 90, 90, 90, 90, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 75 100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 76 110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120, 120, 120}; 77 #define IGP01E1000_AGC_LENGTH_TABLE_SIZE \ 78 (sizeof(e1000_igp_cable_length_table) / \ 79 sizeof(e1000_igp_cable_length_table[0])) 80 81 /** 82 * e1000_init_phy_params_82541 - Init PHY func ptrs. 83 * @hw: pointer to the HW structure 84 **/ 85 static s32 e1000_init_phy_params_82541(struct e1000_hw *hw) 86 { 87 struct e1000_phy_info *phy = &hw->phy; 88 s32 ret_val = E1000_SUCCESS; 89 90 DEBUGFUNC("e1000_init_phy_params_82541"); 91 92 phy->addr = 1; 93 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; 94 phy->reset_delay_us = 10000; 95 phy->type = e1000_phy_igp; 96 97 /* Function Pointers */ 98 phy->ops.check_polarity = e1000_check_polarity_igp; 99 phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_igp; 100 phy->ops.get_cable_length = e1000_get_cable_length_igp_82541; 101 phy->ops.get_cfg_done = e1000_get_cfg_done_generic; 102 phy->ops.get_info = e1000_get_phy_info_igp; 103 phy->ops.read_reg = e1000_read_phy_reg_igp; 104 phy->ops.reset = e1000_phy_hw_reset_82541; 105 phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_82541; 106 phy->ops.write_reg = e1000_write_phy_reg_igp; 107 phy->ops.power_up = e1000_power_up_phy_copper; 108 phy->ops.power_down = e1000_power_down_phy_copper_82541; 109 110 ret_val = e1000_get_phy_id(hw); 111 if (ret_val) 112 goto out; 113 114 /* Verify phy id */ 115 if (phy->id != IGP01E1000_I_PHY_ID) { 116 ret_val = -E1000_ERR_PHY; 117 goto out; 118 } 119 120 out: 121 return ret_val; 122 } 123 124 /** 125 * e1000_init_nvm_params_82541 - Init NVM func ptrs. 126 * @hw: pointer to the HW structure 127 **/ 128 static s32 e1000_init_nvm_params_82541(struct e1000_hw *hw) 129 { 130 struct e1000_nvm_info *nvm = &hw->nvm; 131 s32 ret_val = E1000_SUCCESS; 132 u32 eecd = E1000_READ_REG(hw, E1000_EECD); 133 u16 size; 134 135 DEBUGFUNC("e1000_init_nvm_params_82541"); 136 137 switch (nvm->override) { 138 case e1000_nvm_override_spi_large: 139 nvm->type = e1000_nvm_eeprom_spi; 140 eecd |= E1000_EECD_ADDR_BITS; 141 break; 142 case e1000_nvm_override_spi_small: 143 nvm->type = e1000_nvm_eeprom_spi; 144 eecd &= ~E1000_EECD_ADDR_BITS; 145 break; 146 case e1000_nvm_override_microwire_large: 147 nvm->type = e1000_nvm_eeprom_microwire; 148 eecd |= E1000_EECD_SIZE; 149 break; 150 case e1000_nvm_override_microwire_small: 151 nvm->type = e1000_nvm_eeprom_microwire; 152 eecd &= ~E1000_EECD_SIZE; 153 break; 154 default: 155 nvm->type = eecd & E1000_EECD_TYPE 156 ? e1000_nvm_eeprom_spi 157 : e1000_nvm_eeprom_microwire; 158 break; 159 } 160 161 if (nvm->type == e1000_nvm_eeprom_spi) { 162 nvm->address_bits = (eecd & E1000_EECD_ADDR_BITS) 163 ? 16 : 8; 164 nvm->delay_usec = 1; 165 nvm->opcode_bits = 8; 166 nvm->page_size = (eecd & E1000_EECD_ADDR_BITS) 167 ? 32 : 8; 168 169 /* Function Pointers */ 170 nvm->ops.acquire = e1000_acquire_nvm_generic; 171 nvm->ops.read = e1000_read_nvm_spi; 172 nvm->ops.release = e1000_release_nvm_generic; 173 nvm->ops.update = e1000_update_nvm_checksum_generic; 174 nvm->ops.valid_led_default = e1000_valid_led_default_generic; 175 nvm->ops.validate = e1000_validate_nvm_checksum_generic; 176 nvm->ops.write = e1000_write_nvm_spi; 177 178 /* 179 * nvm->word_size must be discovered after the pointers 180 * are set so we can verify the size from the nvm image 181 * itself. Temporarily set it to a dummy value so the 182 * read will work. 183 */ 184 nvm->word_size = 64; 185 ret_val = nvm->ops.read(hw, NVM_CFG, 1, &size); 186 if (ret_val) 187 goto out; 188 size = (size & NVM_SIZE_MASK) >> NVM_SIZE_SHIFT; 189 /* 190 * if size != 0, it can be added to a constant and become 191 * the left-shift value to set the word_size. Otherwise, 192 * word_size stays at 64. 193 */ 194 if (size) { 195 size += NVM_WORD_SIZE_BASE_SHIFT_82541; 196 nvm->word_size = 1 << size; 197 } 198 } else { 199 nvm->address_bits = (eecd & E1000_EECD_ADDR_BITS) 200 ? 8 : 6; 201 nvm->delay_usec = 50; 202 nvm->opcode_bits = 3; 203 nvm->word_size = (eecd & E1000_EECD_ADDR_BITS) 204 ? 256 : 64; 205 206 /* Function Pointers */ 207 nvm->ops.acquire = e1000_acquire_nvm_generic; 208 nvm->ops.read = e1000_read_nvm_microwire; 209 nvm->ops.release = e1000_release_nvm_generic; 210 nvm->ops.update = e1000_update_nvm_checksum_generic; 211 nvm->ops.valid_led_default = e1000_valid_led_default_generic; 212 nvm->ops.validate = e1000_validate_nvm_checksum_generic; 213 nvm->ops.write = e1000_write_nvm_microwire; 214 } 215 216 out: 217 return ret_val; 218 } 219 220 /** 221 * e1000_init_mac_params_82541 - Init MAC func ptrs. 222 * @hw: pointer to the HW structure 223 **/ 224 static s32 e1000_init_mac_params_82541(struct e1000_hw *hw) 225 { 226 struct e1000_mac_info *mac = &hw->mac; 227 228 DEBUGFUNC("e1000_init_mac_params_82541"); 229 230 /* Set media type */ 231 hw->phy.media_type = e1000_media_type_copper; 232 /* Set mta register count */ 233 mac->mta_reg_count = 128; 234 /* Set rar entry count */ 235 mac->rar_entry_count = E1000_RAR_ENTRIES; 236 /* Set if part includes ASF firmware */ 237 mac->asf_firmware_present = TRUE; 238 239 /* Function Pointers */ 240 241 /* bus type/speed/width */ 242 mac->ops.get_bus_info = e1000_get_bus_info_pci_generic; 243 /* function id */ 244 mac->ops.set_lan_id = e1000_set_lan_id_single_port; 245 /* reset */ 246 mac->ops.reset_hw = e1000_reset_hw_82541; 247 /* hw initialization */ 248 mac->ops.init_hw = e1000_init_hw_82541; 249 /* link setup */ 250 mac->ops.setup_link = e1000_setup_link_generic; 251 /* physical interface link setup */ 252 mac->ops.setup_physical_interface = e1000_setup_copper_link_82541; 253 /* check for link */ 254 mac->ops.check_for_link = e1000_check_for_link_82541; 255 /* link info */ 256 mac->ops.get_link_up_info = e1000_get_link_up_info_82541; 257 /* multicast address update */ 258 mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic; 259 /* writing VFTA */ 260 mac->ops.write_vfta = e1000_write_vfta_generic; 261 /* clearing VFTA */ 262 mac->ops.clear_vfta = e1000_clear_vfta_generic; 263 /* read mac address */ 264 mac->ops.read_mac_addr = e1000_read_mac_addr_82541; 265 /* ID LED init */ 266 mac->ops.id_led_init = e1000_id_led_init_generic; 267 /* setup LED */ 268 mac->ops.setup_led = e1000_setup_led_82541; 269 /* cleanup LED */ 270 mac->ops.cleanup_led = e1000_cleanup_led_82541; 271 /* turn on/off LED */ 272 mac->ops.led_on = e1000_led_on_generic; 273 mac->ops.led_off = e1000_led_off_generic; 274 /* clear hardware counters */ 275 mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_82541; 276 277 return E1000_SUCCESS; 278 } 279 280 /** 281 * e1000_init_function_pointers_82541 - Init func ptrs. 282 * @hw: pointer to the HW structure 283 * 284 * Called to initialize all function pointers and parameters. 285 **/ 286 void e1000_init_function_pointers_82541(struct e1000_hw *hw) 287 { 288 DEBUGFUNC("e1000_init_function_pointers_82541"); 289 290 hw->mac.ops.init_params = e1000_init_mac_params_82541; 291 hw->nvm.ops.init_params = e1000_init_nvm_params_82541; 292 hw->phy.ops.init_params = e1000_init_phy_params_82541; 293 } 294 295 /** 296 * e1000_reset_hw_82541 - Reset hardware 297 * @hw: pointer to the HW structure 298 * 299 * This resets the hardware into a known state. 300 **/ 301 static s32 e1000_reset_hw_82541(struct e1000_hw *hw) 302 { 303 u32 ledctl, ctrl, icr, manc; 304 305 DEBUGFUNC("e1000_reset_hw_82541"); 306 307 DEBUGOUT("Masking off all interrupts\n"); 308 E1000_WRITE_REG(hw, E1000_IMC, 0xFFFFFFFF); 309 310 E1000_WRITE_REG(hw, E1000_RCTL, 0); 311 E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); 312 E1000_WRITE_FLUSH(hw); 313 314 /* 315 * Delay to allow any outstanding PCI transactions to complete 316 * before resetting the device. 317 */ 318 msec_delay(10); 319 320 ctrl = E1000_READ_REG(hw, E1000_CTRL); 321 322 /* Must reset the Phy before resetting the MAC */ 323 if ((hw->mac.type == e1000_82541) || (hw->mac.type == e1000_82547)) { 324 E1000_WRITE_REG(hw, E1000_CTRL, (ctrl | E1000_CTRL_PHY_RST)); 325 msec_delay(5); 326 } 327 328 DEBUGOUT("Issuing a global reset to 82541/82547 MAC\n"); 329 switch (hw->mac.type) { 330 case e1000_82541: 331 case e1000_82541_rev_2: 332 /* 333 * These controllers can't ack the 64-bit write when 334 * issuing the reset, so we use IO-mapping as a 335 * workaround to issue the reset. 336 */ 337 E1000_WRITE_REG_IO(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); 338 break; 339 default: 340 E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); 341 break; 342 } 343 344 /* Wait for NVM reload */ 345 msec_delay(20); 346 347 /* Disable HW ARPs on ASF enabled adapters */ 348 manc = E1000_READ_REG(hw, E1000_MANC); 349 manc &= ~E1000_MANC_ARP_EN; 350 E1000_WRITE_REG(hw, E1000_MANC, manc); 351 352 if ((hw->mac.type == e1000_82541) || (hw->mac.type == e1000_82547)) { 353 e1000_phy_init_script_82541(hw); 354 355 /* Configure activity LED after Phy reset */ 356 ledctl = E1000_READ_REG(hw, E1000_LEDCTL); 357 ledctl &= IGP_ACTIVITY_LED_MASK; 358 ledctl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); 359 E1000_WRITE_REG(hw, E1000_LEDCTL, ledctl); 360 } 361 362 /* Once again, mask the interrupts */ 363 DEBUGOUT("Masking off all interrupts\n"); 364 E1000_WRITE_REG(hw, E1000_IMC, 0xFFFFFFFF); 365 366 /* Clear any pending interrupt events. */ 367 icr = E1000_READ_REG(hw, E1000_ICR); 368 369 return E1000_SUCCESS; 370 } 371 372 /** 373 * e1000_init_hw_82541 - Initialize hardware 374 * @hw: pointer to the HW structure 375 * 376 * This inits the hardware readying it for operation. 377 **/ 378 static s32 e1000_init_hw_82541(struct e1000_hw *hw) 379 { 380 struct e1000_mac_info *mac = &hw->mac; 381 struct e1000_dev_spec_82541 *dev_spec = &hw->dev_spec._82541; 382 u32 i, txdctl; 383 s32 ret_val; 384 385 DEBUGFUNC("e1000_init_hw_82541"); 386 387 /* Initialize identification LED */ 388 ret_val = mac->ops.id_led_init(hw); 389 if (ret_val) { 390 DEBUGOUT("Error initializing identification LED\n"); 391 /* This is not fatal and we should not stop init due to this */ 392 } 393 394 /* Storing the Speed Power Down value for later use */ 395 ret_val = hw->phy.ops.read_reg(hw, 396 IGP01E1000_GMII_FIFO, 397 &dev_spec->spd_default); 398 if (ret_val) 399 goto out; 400 401 /* Disabling VLAN filtering */ 402 DEBUGOUT("Initializing the IEEE VLAN\n"); 403 mac->ops.clear_vfta(hw); 404 405 /* Setup the receive address. */ 406 e1000_init_rx_addrs_generic(hw, mac->rar_entry_count); 407 408 /* Zero out the Multicast HASH table */ 409 DEBUGOUT("Zeroing the MTA\n"); 410 for (i = 0; i < mac->mta_reg_count; i++) { 411 E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); 412 /* 413 * Avoid back to back register writes by adding the register 414 * read (flush). This is to protect against some strange 415 * bridge configurations that may issue Memory Write Block 416 * (MWB) to our register space. 417 */ 418 E1000_WRITE_FLUSH(hw); 419 } 420 421 /* Setup link and flow control */ 422 ret_val = mac->ops.setup_link(hw); 423 424 txdctl = E1000_READ_REG(hw, E1000_TXDCTL(0)); 425 txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) | 426 E1000_TXDCTL_FULL_TX_DESC_WB; 427 E1000_WRITE_REG(hw, E1000_TXDCTL(0), txdctl); 428 429 /* 430 * Clear all of the statistics registers (clear on read). It is 431 * important that we do this after we have tried to establish link 432 * because the symbol error count will increment wildly if there 433 * is no link. 434 */ 435 e1000_clear_hw_cntrs_82541(hw); 436 437 out: 438 return ret_val; 439 } 440 441 /** 442 * e1000_get_link_up_info_82541 - Report speed and duplex 443 * @hw: pointer to the HW structure 444 * @speed: pointer to speed buffer 445 * @duplex: pointer to duplex buffer 446 * 447 * Retrieve the current speed and duplex configuration. 448 **/ 449 static s32 e1000_get_link_up_info_82541(struct e1000_hw *hw, u16 *speed, 450 u16 *duplex) 451 { 452 struct e1000_phy_info *phy = &hw->phy; 453 s32 ret_val; 454 u16 data; 455 456 DEBUGFUNC("e1000_get_link_up_info_82541"); 457 458 ret_val = e1000_get_speed_and_duplex_copper_generic(hw, speed, duplex); 459 if (ret_val) 460 goto out; 461 462 if (!phy->speed_downgraded) 463 goto out; 464 465 /* 466 * IGP01 PHY may advertise full duplex operation after speed 467 * downgrade even if it is operating at half duplex. 468 * Here we set the duplex settings to match the duplex in the 469 * link partner's capabilities. 470 */ 471 ret_val = phy->ops.read_reg(hw, PHY_AUTONEG_EXP, &data); 472 if (ret_val) 473 goto out; 474 475 if (!(data & NWAY_ER_LP_NWAY_CAPS)) { 476 *duplex = HALF_DUPLEX; 477 } else { 478 ret_val = phy->ops.read_reg(hw, PHY_LP_ABILITY, &data); 479 if (ret_val) 480 goto out; 481 482 if (*speed == SPEED_100) { 483 if (!(data & NWAY_LPAR_100TX_FD_CAPS)) 484 *duplex = HALF_DUPLEX; 485 } else if (*speed == SPEED_10) { 486 if (!(data & NWAY_LPAR_10T_FD_CAPS)) 487 *duplex = HALF_DUPLEX; 488 } 489 } 490 491 out: 492 return ret_val; 493 } 494 495 /** 496 * e1000_phy_hw_reset_82541 - PHY hardware reset 497 * @hw: pointer to the HW structure 498 * 499 * Verify the reset block is not blocking us from resetting. Acquire 500 * semaphore (if necessary) and read/set/write the device control reset 501 * bit in the PHY. Wait the appropriate delay time for the device to 502 * reset and release the semaphore (if necessary). 503 **/ 504 static s32 e1000_phy_hw_reset_82541(struct e1000_hw *hw) 505 { 506 s32 ret_val; 507 u32 ledctl; 508 509 DEBUGFUNC("e1000_phy_hw_reset_82541"); 510 511 ret_val = e1000_phy_hw_reset_generic(hw); 512 if (ret_val) 513 goto out; 514 515 e1000_phy_init_script_82541(hw); 516 517 if ((hw->mac.type == e1000_82541) || (hw->mac.type == e1000_82547)) { 518 /* Configure activity LED after PHY reset */ 519 ledctl = E1000_READ_REG(hw, E1000_LEDCTL); 520 ledctl &= IGP_ACTIVITY_LED_MASK; 521 ledctl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); 522 E1000_WRITE_REG(hw, E1000_LEDCTL, ledctl); 523 } 524 525 out: 526 return ret_val; 527 } 528 529 /** 530 * e1000_setup_copper_link_82541 - Configure copper link settings 531 * @hw: pointer to the HW structure 532 * 533 * Calls the appropriate function to configure the link for auto-neg or forced 534 * speed and duplex. Then we check for link, once link is established calls 535 * to configure collision distance and flow control are called. If link is 536 * not established, we return -E1000_ERR_PHY (-2). 537 **/ 538 static s32 e1000_setup_copper_link_82541(struct e1000_hw *hw) 539 { 540 struct e1000_phy_info *phy = &hw->phy; 541 struct e1000_dev_spec_82541 *dev_spec = &hw->dev_spec._82541; 542 s32 ret_val; 543 u32 ctrl, ledctl; 544 545 DEBUGFUNC("e1000_setup_copper_link_82541"); 546 547 ctrl = E1000_READ_REG(hw, E1000_CTRL); 548 ctrl |= E1000_CTRL_SLU; 549 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 550 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 551 552 /* Earlier revs of the IGP phy require us to force MDI. */ 553 if (hw->mac.type == e1000_82541 || hw->mac.type == e1000_82547) { 554 dev_spec->dsp_config = e1000_dsp_config_disabled; 555 phy->mdix = 1; 556 } else { 557 dev_spec->dsp_config = e1000_dsp_config_enabled; 558 } 559 560 ret_val = e1000_copper_link_setup_igp(hw); 561 if (ret_val) 562 goto out; 563 564 if (hw->mac.autoneg) { 565 if (dev_spec->ffe_config == e1000_ffe_config_active) 566 dev_spec->ffe_config = e1000_ffe_config_enabled; 567 } 568 569 /* Configure activity LED after Phy reset */ 570 ledctl = E1000_READ_REG(hw, E1000_LEDCTL); 571 ledctl &= IGP_ACTIVITY_LED_MASK; 572 ledctl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); 573 E1000_WRITE_REG(hw, E1000_LEDCTL, ledctl); 574 575 ret_val = e1000_setup_copper_link_generic(hw); 576 577 out: 578 return ret_val; 579 } 580 581 /** 582 * e1000_check_for_link_82541 - Check/Store link connection 583 * @hw: pointer to the HW structure 584 * 585 * This checks the link condition of the adapter and stores the 586 * results in the hw->mac structure. 587 **/ 588 static s32 e1000_check_for_link_82541(struct e1000_hw *hw) 589 { 590 struct e1000_mac_info *mac = &hw->mac; 591 s32 ret_val; 592 bool link; 593 594 DEBUGFUNC("e1000_check_for_link_82541"); 595 596 /* 597 * We only want to go out to the PHY registers to see if Auto-Neg 598 * has completed and/or if our link status has changed. The 599 * get_link_status flag is set upon receiving a Link Status 600 * Change or Rx Sequence Error interrupt. 601 */ 602 if (!mac->get_link_status) { 603 ret_val = E1000_SUCCESS; 604 goto out; 605 } 606 607 /* 608 * First we want to see if the MII Status Register reports 609 * link. If so, then we want to get the current speed/duplex 610 * of the PHY. 611 */ 612 ret_val = e1000_phy_has_link_generic(hw, 1, 0, &link); 613 if (ret_val) 614 goto out; 615 616 if (!link) { 617 ret_val = e1000_config_dsp_after_link_change_82541(hw, FALSE); 618 goto out; /* No link detected */ 619 } 620 621 mac->get_link_status = FALSE; 622 623 /* 624 * Check if there was DownShift, must be checked 625 * immediately after link-up 626 */ 627 e1000_check_downshift_generic(hw); 628 629 /* 630 * If we are forcing speed/duplex, then we simply return since 631 * we have already determined whether we have link or not. 632 */ 633 if (!mac->autoneg) { 634 ret_val = -E1000_ERR_CONFIG; 635 goto out; 636 } 637 638 ret_val = e1000_config_dsp_after_link_change_82541(hw, TRUE); 639 640 /* 641 * Auto-Neg is enabled. Auto Speed Detection takes care 642 * of MAC speed/duplex configuration. So we only need to 643 * configure Collision Distance in the MAC. 644 */ 645 mac->ops.config_collision_dist(hw); 646 647 /* 648 * Configure Flow Control now that Auto-Neg has completed. 649 * First, we need to restore the desired flow control 650 * settings because we may have had to re-autoneg with a 651 * different link partner. 652 */ 653 ret_val = e1000_config_fc_after_link_up_generic(hw); 654 if (ret_val) { 655 DEBUGOUT("Error configuring flow control\n"); 656 } 657 658 out: 659 return ret_val; 660 } 661 662 /** 663 * e1000_config_dsp_after_link_change_82541 - Config DSP after link 664 * @hw: pointer to the HW structure 665 * @link_up: boolean flag for link up status 666 * 667 * Return E1000_ERR_PHY when failing to read/write the PHY, else E1000_SUCCESS 668 * at any other case. 669 * 670 * 82541_rev_2 & 82547_rev_2 have the capability to configure the DSP when a 671 * gigabit link is achieved to improve link quality. 672 **/ 673 static s32 e1000_config_dsp_after_link_change_82541(struct e1000_hw *hw, 674 bool link_up) 675 { 676 struct e1000_phy_info *phy = &hw->phy; 677 struct e1000_dev_spec_82541 *dev_spec = &hw->dev_spec._82541; 678 s32 ret_val; 679 u32 idle_errs = 0; 680 u16 phy_data, phy_saved_data, speed, duplex, i; 681 u16 ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_20; 682 u16 dsp_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = 683 {IGP01E1000_PHY_AGC_PARAM_A, 684 IGP01E1000_PHY_AGC_PARAM_B, 685 IGP01E1000_PHY_AGC_PARAM_C, 686 IGP01E1000_PHY_AGC_PARAM_D}; 687 688 DEBUGFUNC("e1000_config_dsp_after_link_change_82541"); 689 690 if (link_up) { 691 ret_val = hw->mac.ops.get_link_up_info(hw, &speed, &duplex); 692 if (ret_val) { 693 DEBUGOUT("Error getting link speed and duplex\n"); 694 goto out; 695 } 696 697 if (speed != SPEED_1000) { 698 ret_val = E1000_SUCCESS; 699 goto out; 700 } 701 702 ret_val = phy->ops.get_cable_length(hw); 703 if (ret_val) 704 goto out; 705 706 if ((dev_spec->dsp_config == e1000_dsp_config_enabled) && 707 phy->min_cable_length >= 50) { 708 709 for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { 710 ret_val = phy->ops.read_reg(hw, 711 dsp_reg_array[i], 712 &phy_data); 713 if (ret_val) 714 goto out; 715 716 phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX; 717 718 ret_val = phy->ops.write_reg(hw, 719 dsp_reg_array[i], 720 phy_data); 721 if (ret_val) 722 goto out; 723 } 724 dev_spec->dsp_config = e1000_dsp_config_activated; 725 } 726 727 if ((dev_spec->ffe_config != e1000_ffe_config_enabled) || 728 (phy->min_cable_length >= 50)) { 729 ret_val = E1000_SUCCESS; 730 goto out; 731 } 732 733 /* clear previous idle error counts */ 734 ret_val = phy->ops.read_reg(hw, PHY_1000T_STATUS, &phy_data); 735 if (ret_val) 736 goto out; 737 738 for (i = 0; i < ffe_idle_err_timeout; i++) { 739 usec_delay(1000); 740 ret_val = phy->ops.read_reg(hw, 741 PHY_1000T_STATUS, 742 &phy_data); 743 if (ret_val) 744 goto out; 745 746 idle_errs += (phy_data & SR_1000T_IDLE_ERROR_CNT); 747 if (idle_errs > SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT) { 748 dev_spec->ffe_config = e1000_ffe_config_active; 749 750 ret_val = phy->ops.write_reg(hw, 751 IGP01E1000_PHY_DSP_FFE, 752 IGP01E1000_PHY_DSP_FFE_CM_CP); 753 if (ret_val) 754 goto out; 755 break; 756 } 757 758 if (idle_errs) 759 ffe_idle_err_timeout = 760 FFE_IDLE_ERR_COUNT_TIMEOUT_100; 761 } 762 } else { 763 if (dev_spec->dsp_config == e1000_dsp_config_activated) { 764 /* 765 * Save off the current value of register 0x2F5B 766 * to be restored at the end of the routines. 767 */ 768 ret_val = phy->ops.read_reg(hw, 769 0x2F5B, 770 &phy_saved_data); 771 if (ret_val) 772 goto out; 773 774 /* Disable the PHY transmitter */ 775 ret_val = phy->ops.write_reg(hw, 0x2F5B, 0x0003); 776 if (ret_val) 777 goto out; 778 779 msec_delay_irq(20); 780 781 ret_val = phy->ops.write_reg(hw, 782 0x0000, 783 IGP01E1000_IEEE_FORCE_GIG); 784 if (ret_val) 785 goto out; 786 for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { 787 ret_val = phy->ops.read_reg(hw, 788 dsp_reg_array[i], 789 &phy_data); 790 if (ret_val) 791 goto out; 792 793 phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX; 794 phy_data |= IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS; 795 796 ret_val = phy->ops.write_reg(hw, 797 dsp_reg_array[i], 798 phy_data); 799 if (ret_val) 800 goto out; 801 } 802 803 ret_val = phy->ops.write_reg(hw, 804 0x0000, 805 IGP01E1000_IEEE_RESTART_AUTONEG); 806 if (ret_val) 807 goto out; 808 809 msec_delay_irq(20); 810 811 /* Now enable the transmitter */ 812 ret_val = phy->ops.write_reg(hw, 813 0x2F5B, 814 phy_saved_data); 815 if (ret_val) 816 goto out; 817 818 dev_spec->dsp_config = e1000_dsp_config_enabled; 819 } 820 821 if (dev_spec->ffe_config != e1000_ffe_config_active) { 822 ret_val = E1000_SUCCESS; 823 goto out; 824 } 825 826 /* 827 * Save off the current value of register 0x2F5B 828 * to be restored at the end of the routines. 829 */ 830 ret_val = phy->ops.read_reg(hw, 0x2F5B, &phy_saved_data); 831 if (ret_val) 832 goto out; 833 834 /* Disable the PHY transmitter */ 835 ret_val = phy->ops.write_reg(hw, 0x2F5B, 0x0003); 836 if (ret_val) 837 goto out; 838 839 msec_delay_irq(20); 840 841 ret_val = phy->ops.write_reg(hw, 842 0x0000, 843 IGP01E1000_IEEE_FORCE_GIG); 844 if (ret_val) 845 goto out; 846 847 ret_val = phy->ops.write_reg(hw, 848 IGP01E1000_PHY_DSP_FFE, 849 IGP01E1000_PHY_DSP_FFE_DEFAULT); 850 if (ret_val) 851 goto out; 852 853 ret_val = phy->ops.write_reg(hw, 854 0x0000, 855 IGP01E1000_IEEE_RESTART_AUTONEG); 856 if (ret_val) 857 goto out; 858 859 msec_delay_irq(20); 860 861 /* Now enable the transmitter */ 862 ret_val = phy->ops.write_reg(hw, 0x2F5B, phy_saved_data); 863 864 if (ret_val) 865 goto out; 866 867 dev_spec->ffe_config = e1000_ffe_config_enabled; 868 } 869 870 out: 871 return ret_val; 872 } 873 874 /** 875 * e1000_get_cable_length_igp_82541 - Determine cable length for igp PHY 876 * @hw: pointer to the HW structure 877 * 878 * The automatic gain control (agc) normalizes the amplitude of the 879 * received signal, adjusting for the attenuation produced by the 880 * cable. By reading the AGC registers, which represent the 881 * combination of coarse and fine gain value, the value can be put 882 * into a lookup table to obtain the approximate cable length 883 * for each channel. 884 **/ 885 static s32 e1000_get_cable_length_igp_82541(struct e1000_hw *hw) 886 { 887 struct e1000_phy_info *phy = &hw->phy; 888 s32 ret_val = E1000_SUCCESS; 889 u16 i, data; 890 u16 cur_agc_value, agc_value = 0; 891 u16 min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE; 892 u16 agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = 893 {IGP01E1000_PHY_AGC_A, 894 IGP01E1000_PHY_AGC_B, 895 IGP01E1000_PHY_AGC_C, 896 IGP01E1000_PHY_AGC_D}; 897 898 DEBUGFUNC("e1000_get_cable_length_igp_82541"); 899 900 /* Read the AGC registers for all channels */ 901 for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { 902 ret_val = phy->ops.read_reg(hw, agc_reg_array[i], &data); 903 if (ret_val) 904 goto out; 905 906 cur_agc_value = data >> IGP01E1000_AGC_LENGTH_SHIFT; 907 908 /* Bounds checking */ 909 if ((cur_agc_value >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) || 910 (cur_agc_value == 0)) { 911 ret_val = -E1000_ERR_PHY; 912 goto out; 913 } 914 915 agc_value += cur_agc_value; 916 917 if (min_agc_value > cur_agc_value) 918 min_agc_value = cur_agc_value; 919 } 920 921 /* Remove the minimal AGC result for length < 50m */ 922 if (agc_value < IGP01E1000_PHY_CHANNEL_NUM * 50) { 923 agc_value -= min_agc_value; 924 /* Average the three remaining channels for the length. */ 925 agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1); 926 } else { 927 /* Average the channels for the length. */ 928 agc_value /= IGP01E1000_PHY_CHANNEL_NUM; 929 } 930 931 phy->min_cable_length = (e1000_igp_cable_length_table[agc_value] > 932 IGP01E1000_AGC_RANGE) 933 ? (e1000_igp_cable_length_table[agc_value] - 934 IGP01E1000_AGC_RANGE) 935 : 0; 936 phy->max_cable_length = e1000_igp_cable_length_table[agc_value] + 937 IGP01E1000_AGC_RANGE; 938 939 phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2; 940 941 out: 942 return ret_val; 943 } 944 945 /** 946 * e1000_set_d3_lplu_state_82541 - Sets low power link up state for D3 947 * @hw: pointer to the HW structure 948 * @active: boolean used to enable/disable lplu 949 * 950 * Success returns 0, Failure returns 1 951 * 952 * The low power link up (lplu) state is set to the power management level D3 953 * and SmartSpeed is disabled when active is TRUE, else clear lplu for D3 954 * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU 955 * is used during Dx states where the power conservation is most important. 956 * During driver activity, SmartSpeed should be enabled so performance is 957 * maintained. 958 **/ 959 static s32 e1000_set_d3_lplu_state_82541(struct e1000_hw *hw, bool active) 960 { 961 struct e1000_phy_info *phy = &hw->phy; 962 s32 ret_val; 963 u16 data; 964 965 DEBUGFUNC("e1000_set_d3_lplu_state_82541"); 966 967 switch (hw->mac.type) { 968 case e1000_82541_rev_2: 969 case e1000_82547_rev_2: 970 break; 971 default: 972 ret_val = e1000_set_d3_lplu_state_generic(hw, active); 973 goto out; 974 break; 975 } 976 977 ret_val = phy->ops.read_reg(hw, IGP01E1000_GMII_FIFO, &data); 978 if (ret_val) 979 goto out; 980 981 if (!active) { 982 data &= ~IGP01E1000_GMII_FLEX_SPD; 983 ret_val = phy->ops.write_reg(hw, IGP01E1000_GMII_FIFO, data); 984 if (ret_val) 985 goto out; 986 987 /* 988 * LPLU and SmartSpeed are mutually exclusive. LPLU is used 989 * during Dx states where the power conservation is most 990 * important. During driver activity we should enable 991 * SmartSpeed, so performance is maintained. 992 */ 993 if (phy->smart_speed == e1000_smart_speed_on) { 994 ret_val = phy->ops.read_reg(hw, 995 IGP01E1000_PHY_PORT_CONFIG, 996 &data); 997 if (ret_val) 998 goto out; 999 1000 data |= IGP01E1000_PSCFR_SMART_SPEED; 1001 ret_val = phy->ops.write_reg(hw, 1002 IGP01E1000_PHY_PORT_CONFIG, 1003 data); 1004 if (ret_val) 1005 goto out; 1006 } else if (phy->smart_speed == e1000_smart_speed_off) { 1007 ret_val = phy->ops.read_reg(hw, 1008 IGP01E1000_PHY_PORT_CONFIG, 1009 &data); 1010 if (ret_val) 1011 goto out; 1012 1013 data &= ~IGP01E1000_PSCFR_SMART_SPEED; 1014 ret_val = phy->ops.write_reg(hw, 1015 IGP01E1000_PHY_PORT_CONFIG, 1016 data); 1017 if (ret_val) 1018 goto out; 1019 } 1020 } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) || 1021 (phy->autoneg_advertised == E1000_ALL_NOT_GIG) || 1022 (phy->autoneg_advertised == E1000_ALL_10_SPEED)) { 1023 data |= IGP01E1000_GMII_FLEX_SPD; 1024 ret_val = phy->ops.write_reg(hw, IGP01E1000_GMII_FIFO, data); 1025 if (ret_val) 1026 goto out; 1027 1028 /* When LPLU is enabled, we should disable SmartSpeed */ 1029 ret_val = phy->ops.read_reg(hw, 1030 IGP01E1000_PHY_PORT_CONFIG, 1031 &data); 1032 if (ret_val) 1033 goto out; 1034 1035 data &= ~IGP01E1000_PSCFR_SMART_SPEED; 1036 ret_val = phy->ops.write_reg(hw, 1037 IGP01E1000_PHY_PORT_CONFIG, 1038 data); 1039 } 1040 1041 out: 1042 return ret_val; 1043 } 1044 1045 /** 1046 * e1000_setup_led_82541 - Configures SW controllable LED 1047 * @hw: pointer to the HW structure 1048 * 1049 * This prepares the SW controllable LED for use and saves the current state 1050 * of the LED so it can be later restored. 1051 **/ 1052 static s32 e1000_setup_led_82541(struct e1000_hw *hw) 1053 { 1054 struct e1000_dev_spec_82541 *dev_spec = &hw->dev_spec._82541; 1055 s32 ret_val; 1056 1057 DEBUGFUNC("e1000_setup_led_82541"); 1058 1059 ret_val = hw->phy.ops.read_reg(hw, 1060 IGP01E1000_GMII_FIFO, 1061 &dev_spec->spd_default); 1062 if (ret_val) 1063 goto out; 1064 1065 ret_val = hw->phy.ops.write_reg(hw, 1066 IGP01E1000_GMII_FIFO, 1067 (u16)(dev_spec->spd_default & 1068 ~IGP01E1000_GMII_SPD)); 1069 if (ret_val) 1070 goto out; 1071 1072 E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_mode1); 1073 1074 out: 1075 return ret_val; 1076 } 1077 1078 /** 1079 * e1000_cleanup_led_82541 - Set LED config to default operation 1080 * @hw: pointer to the HW structure 1081 * 1082 * Remove the current LED configuration and set the LED configuration 1083 * to the default value, saved from the EEPROM. 1084 **/ 1085 static s32 e1000_cleanup_led_82541(struct e1000_hw *hw) 1086 { 1087 struct e1000_dev_spec_82541 *dev_spec = &hw->dev_spec._82541; 1088 s32 ret_val; 1089 1090 DEBUGFUNC("e1000_cleanup_led_82541"); 1091 1092 ret_val = hw->phy.ops.write_reg(hw, 1093 IGP01E1000_GMII_FIFO, 1094 dev_spec->spd_default); 1095 if (ret_val) 1096 goto out; 1097 1098 E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_default); 1099 1100 out: 1101 return ret_val; 1102 } 1103 1104 /** 1105 * e1000_phy_init_script_82541 - Initialize GbE PHY 1106 * @hw: pointer to the HW structure 1107 * 1108 * Initializes the IGP PHY. 1109 **/ 1110 static s32 e1000_phy_init_script_82541(struct e1000_hw *hw) 1111 { 1112 struct e1000_dev_spec_82541 *dev_spec = &hw->dev_spec._82541; 1113 u32 ret_val; 1114 u16 phy_saved_data; 1115 1116 DEBUGFUNC("e1000_phy_init_script_82541"); 1117 1118 if (!dev_spec->phy_init_script) { 1119 ret_val = E1000_SUCCESS; 1120 goto out; 1121 } 1122 1123 /* Delay after phy reset to enable NVM configuration to load */ 1124 msec_delay(20); 1125 1126 /* 1127 * Save off the current value of register 0x2F5B to be restored at 1128 * the end of this routine. 1129 */ 1130 ret_val = hw->phy.ops.read_reg(hw, 0x2F5B, &phy_saved_data); 1131 1132 /* Disabled the PHY transmitter */ 1133 hw->phy.ops.write_reg(hw, 0x2F5B, 0x0003); 1134 1135 msec_delay(20); 1136 1137 hw->phy.ops.write_reg(hw, 0x0000, 0x0140); 1138 1139 msec_delay(5); 1140 1141 switch (hw->mac.type) { 1142 case e1000_82541: 1143 case e1000_82547: 1144 hw->phy.ops.write_reg(hw, 0x1F95, 0x0001); 1145 1146 hw->phy.ops.write_reg(hw, 0x1F71, 0xBD21); 1147 1148 hw->phy.ops.write_reg(hw, 0x1F79, 0x0018); 1149 1150 hw->phy.ops.write_reg(hw, 0x1F30, 0x1600); 1151 1152 hw->phy.ops.write_reg(hw, 0x1F31, 0x0014); 1153 1154 hw->phy.ops.write_reg(hw, 0x1F32, 0x161C); 1155 1156 hw->phy.ops.write_reg(hw, 0x1F94, 0x0003); 1157 1158 hw->phy.ops.write_reg(hw, 0x1F96, 0x003F); 1159 1160 hw->phy.ops.write_reg(hw, 0x2010, 0x0008); 1161 break; 1162 case e1000_82541_rev_2: 1163 case e1000_82547_rev_2: 1164 hw->phy.ops.write_reg(hw, 0x1F73, 0x0099); 1165 break; 1166 default: 1167 break; 1168 } 1169 1170 hw->phy.ops.write_reg(hw, 0x0000, 0x3300); 1171 1172 msec_delay(20); 1173 1174 /* Now enable the transmitter */ 1175 hw->phy.ops.write_reg(hw, 0x2F5B, phy_saved_data); 1176 1177 if (hw->mac.type == e1000_82547) { 1178 u16 fused, fine, coarse; 1179 1180 /* Move to analog registers page */ 1181 hw->phy.ops.read_reg(hw, 1182 IGP01E1000_ANALOG_SPARE_FUSE_STATUS, 1183 &fused); 1184 1185 if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) { 1186 hw->phy.ops.read_reg(hw, 1187 IGP01E1000_ANALOG_FUSE_STATUS, 1188 &fused); 1189 1190 fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK; 1191 coarse = fused & IGP01E1000_ANALOG_FUSE_COARSE_MASK; 1192 1193 if (coarse > IGP01E1000_ANALOG_FUSE_COARSE_THRESH) { 1194 coarse -= IGP01E1000_ANALOG_FUSE_COARSE_10; 1195 fine -= IGP01E1000_ANALOG_FUSE_FINE_1; 1196 } else if (coarse == 1197 IGP01E1000_ANALOG_FUSE_COARSE_THRESH) 1198 fine -= IGP01E1000_ANALOG_FUSE_FINE_10; 1199 1200 fused = (fused & IGP01E1000_ANALOG_FUSE_POLY_MASK) | 1201 (fine & IGP01E1000_ANALOG_FUSE_FINE_MASK) | 1202 (coarse & IGP01E1000_ANALOG_FUSE_COARSE_MASK); 1203 1204 hw->phy.ops.write_reg(hw, 1205 IGP01E1000_ANALOG_FUSE_CONTROL, 1206 fused); 1207 hw->phy.ops.write_reg(hw, 1208 IGP01E1000_ANALOG_FUSE_BYPASS, 1209 IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL); 1210 } 1211 } 1212 1213 out: 1214 return ret_val; 1215 } 1216 1217 /** 1218 * e1000_init_script_state_82541 - Enable/Disable PHY init script 1219 * @hw: pointer to the HW structure 1220 * @state: boolean value used to enable/disable PHY init script 1221 * 1222 * Allows the driver to enable/disable the PHY init script, if the PHY is an 1223 * IGP PHY. 1224 **/ 1225 void e1000_init_script_state_82541(struct e1000_hw *hw, bool state) 1226 { 1227 struct e1000_dev_spec_82541 *dev_spec = &hw->dev_spec._82541; 1228 1229 DEBUGFUNC("e1000_init_script_state_82541"); 1230 1231 if (hw->phy.type != e1000_phy_igp) { 1232 DEBUGOUT("Initialization script not necessary.\n"); 1233 goto out; 1234 } 1235 1236 dev_spec->phy_init_script = state; 1237 1238 out: 1239 return; 1240 } 1241 1242 /** 1243 * e1000_power_down_phy_copper_82541 - Remove link in case of PHY power down 1244 * @hw: pointer to the HW structure 1245 * 1246 * In the case of a PHY power down to save power, or to turn off link during a 1247 * driver unload, or wake on lan is not enabled, remove the link. 1248 **/ 1249 static void e1000_power_down_phy_copper_82541(struct e1000_hw *hw) 1250 { 1251 /* If the management interface is not enabled, then power down */ 1252 if (!(E1000_READ_REG(hw, E1000_MANC) & E1000_MANC_SMBUS_EN)) 1253 e1000_power_down_phy_copper(hw); 1254 1255 return; 1256 } 1257 1258 /** 1259 * e1000_clear_hw_cntrs_82541 - Clear device specific hardware counters 1260 * @hw: pointer to the HW structure 1261 * 1262 * Clears the hardware counters by reading the counter registers. 1263 **/ 1264 static void e1000_clear_hw_cntrs_82541(struct e1000_hw *hw) 1265 { 1266 DEBUGFUNC("e1000_clear_hw_cntrs_82541"); 1267 1268 e1000_clear_hw_cntrs_base_generic(hw); 1269 1270 E1000_READ_REG(hw, E1000_PRC64); 1271 E1000_READ_REG(hw, E1000_PRC127); 1272 E1000_READ_REG(hw, E1000_PRC255); 1273 E1000_READ_REG(hw, E1000_PRC511); 1274 E1000_READ_REG(hw, E1000_PRC1023); 1275 E1000_READ_REG(hw, E1000_PRC1522); 1276 E1000_READ_REG(hw, E1000_PTC64); 1277 E1000_READ_REG(hw, E1000_PTC127); 1278 E1000_READ_REG(hw, E1000_PTC255); 1279 E1000_READ_REG(hw, E1000_PTC511); 1280 E1000_READ_REG(hw, E1000_PTC1023); 1281 E1000_READ_REG(hw, E1000_PTC1522); 1282 1283 E1000_READ_REG(hw, E1000_ALGNERRC); 1284 E1000_READ_REG(hw, E1000_RXERRC); 1285 E1000_READ_REG(hw, E1000_TNCRS); 1286 E1000_READ_REG(hw, E1000_CEXTERR); 1287 E1000_READ_REG(hw, E1000_TSCTC); 1288 E1000_READ_REG(hw, E1000_TSCTFC); 1289 1290 E1000_READ_REG(hw, E1000_MGTPRC); 1291 E1000_READ_REG(hw, E1000_MGTPDC); 1292 E1000_READ_REG(hw, E1000_MGTPTC); 1293 } 1294 1295 /** 1296 * e1000_read_mac_addr_82541 - Read device MAC address 1297 * @hw: pointer to the HW structure 1298 * 1299 * Reads the device MAC address from the EEPROM and stores the value. 1300 **/ 1301 static s32 e1000_read_mac_addr_82541(struct e1000_hw *hw) 1302 { 1303 s32 ret_val = E1000_SUCCESS; 1304 u16 offset, nvm_data, i; 1305 1306 DEBUGFUNC("e1000_read_mac_addr"); 1307 1308 for (i = 0; i < ETH_ADDR_LEN; i += 2) { 1309 offset = i >> 1; 1310 ret_val = hw->nvm.ops.read(hw, offset, 1, &nvm_data); 1311 if (ret_val) { 1312 DEBUGOUT("NVM Read Error\n"); 1313 goto out; 1314 } 1315 hw->mac.perm_addr[i] = (u8)(nvm_data & 0xFF); 1316 hw->mac.perm_addr[i+1] = (u8)(nvm_data >> 8); 1317 } 1318 1319 for (i = 0; i < ETH_ADDR_LEN; i++) 1320 hw->mac.addr[i] = hw->mac.perm_addr[i]; 1321 1322 out: 1323 return ret_val; 1324 } 1325
Cache object: 9e597574da86f09e2c855f4fa0ac781d
[ source navigation ] [ diff markup ] [ identifier search ] [ freetext search ] [ file search ] [ list types ] [ track identifier ]