1 /* $NetBSD: ncr53c9xreg.h,v 1.16 2009/09/07 13:31:44 tsutsui Exp $ */
2
3 /*-
4 * SPDX-License-Identifier: BSD-4-Clause
5 *
6 * Copyright (c) 1994 Peter Galbavy. All rights reserved.
7 *
8 * Redistribution and use in source and binary forms, with or without
9 * modification, are permitted provided that the following conditions
10 * are met:
11 * 1. Redistributions of source code must retain the above copyright
12 * notice, this list of conditions and the following disclaimer.
13 * 2. Redistributions in binary form must reproduce the above copyright
14 * notice, this list of conditions and the following disclaimer in the
15 * documentation and/or other materials provided with the distribution.
16 * 3. All advertising materials mentioning features or use of this software
17 * must display the following acknowledgement:
18 * This product includes software developed by Peter Galbavy.
19 * 4. The name of the author may not be used to endorse or promote products
20 * derived from this software without specific prior written permission.
21 *
22 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
23 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
24 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
25 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
26 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
27 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
28 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
29 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
30 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
31 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
32 */
33
34 /* $FreeBSD$ */
35
36 #ifndef _NCR53C9XREG_H_
37 #define _NCR53C9XREG_H_
38
39 /*
40 * Register addresses, relative to some base address
41 */
42
43 #define NCR_TCL 0x00 /* RW - Transfer Count Low */
44 #define NCR_TCM 0x01 /* RW - Transfer Count Mid */
45 #define NCR_TCH 0x0e /* RW - Transfer Count High */
46 /* NOT on 53C90 */
47
48 #define NCR_FIFO 0x02 /* RW - FIFO data */
49
50 #define NCR_CMD 0x03 /* RW - Command (2 deep) */
51 #define NCRCMD_DMA 0x80 /* DMA Bit */
52 #define NCRCMD_NOP 0x00 /* No Operation */
53 #define NCRCMD_FLUSH 0x01 /* Flush FIFO */
54 #define NCRCMD_RSTCHIP 0x02 /* Reset Chip */
55 #define NCRCMD_RSTSCSI 0x03 /* Reset SCSI Bus */
56 #define NCRCMD_RESEL 0x40 /* Reselect Sequence */
57 #define NCRCMD_SELNATN 0x41 /* Select without ATN */
58 #define NCRCMD_SELATN 0x42 /* Select with ATN */
59 #define NCRCMD_SELATNS 0x43 /* Select with ATN & Stop */
60 #define NCRCMD_ENSEL 0x44 /* Enable (Re)Selection */
61 #define NCRCMD_DISSEL 0x45 /* Disable (Re)Selection */
62 #define NCRCMD_SELATN3 0x46 /* Select with ATN3 */
63 #define NCRCMD_RESEL3 0x47 /* Reselect3 Sequence */
64 #define NCRCMD_SNDMSG 0x20 /* Send Message */
65 #define NCRCMD_SNDSTAT 0x21 /* Send Status */
66 #define NCRCMD_SNDDATA 0x22 /* Send Data */
67 #define NCRCMD_DISCSEQ 0x23 /* Disconnect Sequence */
68 #define NCRCMD_TERMSEQ 0x24 /* Terminate Sequence */
69 #define NCRCMD_TCCS 0x25 /* Target Command Comp Seq */
70 #define NCRCMD_DISC 0x27 /* Disconnect */
71 #define NCRCMD_RECMSG 0x28 /* Receive Message */
72 #define NCRCMD_RECCMD 0x29 /* Receive Command */
73 #define NCRCMD_RECDATA 0x2a /* Receive Data */
74 #define NCRCMD_RECCSEQ 0x2b /* Receive Command Sequence*/
75 #define NCRCMD_ABORT 0x04 /* Target Abort DMA */
76 #define NCRCMD_TRANS 0x10 /* Transfer Information */
77 #define NCRCMD_ICCS 0x11 /* Initiator Cmd Comp Seq */
78 #define NCRCMD_MSGOK 0x12 /* Message Accepted */
79 #define NCRCMD_TRPAD 0x18 /* Transfer Pad */
80 #define NCRCMD_SETATN 0x1a /* Set ATN */
81 #define NCRCMD_RSTATN 0x1b /* Reset ATN */
82
83 #define NCR_STAT 0x04 /* RO - Status */
84 #define NCRSTAT_INT 0x80 /* Interrupt */
85 #define NCRSTAT_GE 0x40 /* Gross Error */
86 #define NCRSTAT_PE 0x20 /* Parity Error */
87 #define NCRSTAT_TC 0x10 /* Terminal Count */
88 #define NCRSTAT_VGC 0x08 /* Valid Group Code */
89 #define NCRSTAT_PHASE 0x07 /* Phase bits */
90
91 #define NCR_SELID 0x04 /* WO - Select/Reselect Bus ID */
92 #define NCR_BUSID_HMEXC32 0x40 /* HME xfer counter is 32bit */
93 #define NCR_BUSID_HMEENCID 0x10 /* HME encode reselection ID */
94
95 #define NCR_INTR 0x05 /* RO - Interrupt */
96 #define NCRINTR_SBR 0x80 /* SCSI Bus Reset */
97 #define NCRINTR_ILL 0x40 /* Illegal Command */
98 #define NCRINTR_DIS 0x20 /* Disconnect */
99 #define NCRINTR_BS 0x10 /* Bus Service */
100 #define NCRINTR_FC 0x08 /* Function Complete */
101 #define NCRINTR_RESEL 0x04 /* Reselected */
102 #define NCRINTR_SELATN 0x02 /* Select with ATN */
103 #define NCRINTR_SEL 0x01 /* Selected */
104
105 #define NCR_TIMEOUT 0x05 /* WO - Select/Reselect Timeout */
106
107 #define NCR_STEP 0x06 /* RO - Sequence Step */
108 #define NCRSTEP_MASK 0x07 /* the last 3 bits */
109 #define NCRSTEP_DONE 0x04 /* command went out */
110
111 #define NCR_SYNCTP 0x06 /* WO - Synch Transfer Period */
112 /* Default 5 (53C9X) */
113
114 #define NCR_FFLAG 0x07 /* RO - FIFO Flags */
115 #define NCRFIFO_SS 0xe0 /* Sequence Step (Dup) */
116 #define NCRFIFO_FF 0x1f /* Bytes in FIFO */
117
118 #define NCR_SYNCOFF 0x07 /* WO - Synch Offset */
119 /* 0 = ASYNC */
120 /* 1 - 15 = SYNC bytes */
121
122 #define NCR_CFG1 0x08 /* RW - Configuration #1 */
123 #define NCRCFG1_SLOW 0x80 /* Slow Cable Mode */
124 #define NCRCFG1_SRR 0x40 /* SCSI Reset Rep Int Dis */
125 #define NCRCFG1_PTEST 0x20 /* Parity Test Mod */
126 #define NCRCFG1_PARENB 0x10 /* Enable Parity Check */
127 #define NCRCFG1_CTEST 0x08 /* Enable Chip Test */
128 #define NCRCFG1_BUSID 0x07 /* Bus ID */
129
130 #define NCR_CCF 0x09 /* WO - Clock Conversion Factor */
131 /* 0 = 35.01 - 40MHz */
132 /* NEVER SET TO 1 */
133 /* 2 = 10MHz */
134 /* 3 = 10.01 - 15MHz */
135 /* 4 = 15.01 - 20MHz */
136 /* 5 = 20.01 - 25MHz */
137 /* 6 = 25.01 - 30MHz */
138 /* 7 = 30.01 - 35MHz */
139
140 #define NCR_TEST 0x0a /* WO - Test (Chip Test Only) */
141
142 #define NCR_CFG2 0x0b /* RW - Configuration #2 */
143 #define NCRCFG2_RSVD 0xa0 /* reserved */
144 #define NCRCFG2_FE 0x40 /* Features Enable */
145 #define NCRCFG2_DREQ 0x10 /* DREQ High Impedance */
146 #define NCRCFG2_SCSI2 0x08 /* SCSI-2 Enable */
147 #define NCRCFG2_BPA 0x04 /* Target Bad Parity Abort */
148 #define NCRCFG2_RPE 0x02 /* Register Parity Error */
149 #define NCRCFG2_DPE 0x01 /* DMA Parity Error */
150
151 #define NCRCFG2_HMEFE 0x10 /* HME feature enable */
152 #define NCRCFG2_HME32 0x80 /* HME 32 extended */
153
154 /* Config #3 only on 53C9X */
155 #define NCR_CFG3 0x0c /* RW - Configuration #3 */
156 #define NCRCFG3_RSVD 0xe0 /* reserved */
157 #define NCRCFG3_IDM 0x10 /* ID Message Res Check */
158 #define NCRCFG3_QTE 0x08 /* Queue Tag Enable */
159 #define NCRCFG3_CDB 0x04 /* CDB 10-bytes OK */
160 #define NCRCFG3_FSCSI 0x02 /* Fast SCSI */
161 #define NCRCFG3_FCLK 0x01 /* Fast Clock (>25MHz) */
162
163 /*
164 * For some unknown reason, the ESP406/FAS408 looks like every
165 * other ncr53c9x, except for configuration #3 register. At any
166 * rate, if you're dealing with these chips, you need to use these
167 * defines instead.
168 */
169
170 /* Config #3 different on ESP406/FAS408 */
171 #define NCR_ESPCFG3 0x0c /* RW - Configuration #3 */
172 #define NCRESPCFG3_IDM 0x80 /* ID Message Res Check */
173 #define NCRESPCFG3_QTE 0x40 /* Queue Tag Enable */
174 #define NCRESPCFG3_CDB 0x20 /* CDB 10-bytes OK */
175 #define NCRESPCFG3_FSCSI 0x10 /* Fast SCSI */
176 #define NCRESPCFG3_SRESB 0x08 /* Save Residual Byte */
177 #define NCRESPCFG3_FCLK 0x04 /* Fast Clock (>25MHz) */
178 #define NCRESPCFG3_ADMA 0x02 /* Alternate DMA Mode */
179 #define NCRESPCFG3_T8M 0x01 /* Threshold 8 Mode */
180
181 /* Config #3 also different on NCR53CF9x/FAS100A/FAS216/FAS236 */
182 #define NCR_F9XCFG3 0x0c /* RW - Configuration #3 */
183 #define NCRF9XCFG3_IDM 0x80 /* ID Message Res Check */
184 #define NCRF9XCFG3_QTE 0x40 /* Queue Tag Enable */
185 #define NCRF9XCFG3_CDB 0x20 /* CDB 10-bytes OK */
186 #define NCRF9XCFG3_FSCSI 0x10 /* Fast SCSI */
187 #define NCRF9XCFG3_FCLK 0x08 /* Fast Clock (>25MHz) */
188 #define NCRF9XCFG3_SRESB 0x04 /* Save Residual Byte */
189 #define NCRF9XCFG3_ADMA 0x02 /* Alternate DMA Mode */
190 #define NCRF9XCFG3_T8M 0x01 /* Threshold 8 Mode */
191
192 /* Config #3 on FAS366 */
193 #define NCRFASCFG3_OBAUTO 0x80 /* auto push odd-byte to DMA */
194 #define NCRFASCFG3_EWIDE 0x40 /* Enable Wide-SCSI */
195 #define NCRFASCFG3_IDBIT3 0x20 /* Bit 3 of HME SCSI-ID */
196 #define NCRFASCFG3_IDRESCHK 0x10 /* ID message checking */
197 #define NCRFASCFG3_QUENB 0x08 /* 3-byte msg support */
198 #define NCRFASCFG3_CDB10 0x04 /* group 2 scsi-2 support */
199 #define NCRFASCFG3_FASTSCSI 0x02 /* 10 MB/S fast scsi mode */
200 #define NCRFASCFG3_FASTCLK 0x01 /* fast clock mode */
201
202 /* Config #4 only on ESP406/FAS408 */
203 #define NCR_CFG4 0x0d /* RW - Configuration #4 */
204 #define NCRCFG4_CRS1 0x80 /* Select register set #1 */
205 #define NCRCFG4_RSVD 0x7b /* reserved */
206 #define NCRCFG4_ACTNEG 0x04 /* Active negation */
207
208 /*
209 The following registers are only on the ESP406/FAS408. The
210 documentation refers to them as "Control Register Set #1".
211 These are the registers that are visible when bit 7 of
212 register 0x0d is set. This bit is common to both register sets.
213 */
214
215 #define NCR_JMP 0x00 /* RO - Jumper Sense Register */
216 #define NCRJMP_RSVD 0xc0 /* reserved */
217 #define NCRJMP_ROMSZ 0x20 /* ROM Size 1=16K, 0=32K */
218 #define NCRJMP_J4 0x10 /* Jumper #4 */
219 #define NCRJMP_J3 0x08 /* Jumper #3 */
220 #define NCRJMP_J2 0x04 /* Jumper #2 */
221 #define NCRJMP_J1 0x02 /* Jumper #1 */
222 #define NCRJMP_J0 0x01 /* Jumper #0 */
223
224 #define NCR_PIOFIFO 0x04 /* WO - PIO FIFO, 4 bytes deep */
225
226 #define NCR_PSTAT 0x08 /* RW - PIO Status Register */
227 #define NCRPSTAT_PERR 0x80 /* PIO Error */
228 #define NCRPSTAT_SIRQ 0x40 /* Active High of SCSI IRQ */
229 #define NCRPSTAT_ATAI 0x20 /* ATA IRQ */
230 #define NCRPSTAT_FEMPT 0x10 /* PIO FIFO Empty */
231 #define NCRPSTAT_F13 0x08 /* PIO FIFO 1/3 */
232 #define NCRPSTAT_F23 0x04 /* PIO FIFO 2/3 */
233 #define NCRPSTAT_FFULL 0x02 /* PIO FIFO Full */
234 #define NCRPSTAT_PIOM 0x01 /* PIO/DMA Mode */
235
236 #define NCR_PIOI 0x0b /* RW - PIO Interrupt Enable */
237 #define NCRPIOI_RSVD 0xe0 /* reserved */
238 #define NCRPIOI_EMPTY 0x10 /* IRQ When Empty */
239 #define NCRPIOI_13 0x08 /* IRQ When 1/3 */
240 #define NCRPIOI_23 0x04 /* IRQ When 2/3 */
241 #define NCRPIOI_FULL 0x02 /* IRQ When Full */
242 #define NCRPIOI_FINV 0x01 /* Flag Invert */
243
244 #define NCR_CFG5 0x0d /* RW - Configuration #5 */
245 #define NCRCFG5_CRS1 0x80 /* Select Register Set #1 */
246 #define NCRCFG5_SRAM 0x40 /* SRAM Memory Map */
247 #define NCRCFG5_AADDR 0x20 /* Auto Address */
248 #define NCRCFG5_PTRINC 0x10 /* Pointer Increment */
249 #define NCRCFG5_LOWPWR 0x08 /* Low Power Mode */
250 #define NCRCFG5_SINT 0x04 /* SCSI Interrupt Enable */
251 #define NCRCFG5_INTP 0x02 /* INT Polarity */
252 #define NCRCFG5_AINT 0x01 /* ATA Interrupt Enable */
253
254 #define NCR_SIGNTR 0x0e /* RO - Signature */
255
256 /* Am53c974 Config #3 */
257 #define NCR_AMDCFG3 0x0c /* RW - Configuration #3 */
258 #define NCRAMDCFG3_IDM 0x80 /* ID Message Res Check */
259 #define NCRAMDCFG3_QTE 0x40 /* Queue Tag Enable */
260 #define NCRAMDCFG3_CDB 0x20 /* CDB 10-bytes OK */
261 #define NCRAMDCFG3_FSCSI 0x10 /* Fast SCSI */
262 #define NCRAMDCFG3_FCLK 0x08 /* Fast Clock (40MHz) */
263 #define NCRAMDCFG3_RSVD 0x07 /* Reserved */
264
265 /* Am53c974 Config #4 */
266 #define NCR_AMDCFG4 0x0d /* RW - Configuration #4 */
267 #define NCRAMDCFG4_GE 0xc0 /* Glitch Eater */
268 #define NCRAMDCFG4_GE12NS 0x00 /* Signal window 12ns */
269 #define NCRAMDCFG4_GE25NS 0x80 /* Signal window 25ns */
270 #define NCRAMDCFG4_GE35NS 0x40 /* Signal window 35ns */
271 #define NCRAMDCFG4_GE0NS 0xc0 /* Signal window 0ns */
272 #define NCRAMDCFG4_PWD 0x20 /* Reduced power feature */
273 #define NCRAMDCFG4_RSVD 0x13 /* Reserved */
274 #define NCRAMDCFG4_RAE 0x08 /* Active neg. REQ/ACK */
275 #define NCRAMDCFG4_RADE 0x04 /* Active neg. REQ/ACK/DAT */
276
277 /*
278 * FAS366
279 */
280 #define NCR_RCL NCR_TCH /* Recommand counter low */
281 #define NCR_RCH 0xf /* Recommand counter high */
282 #define NCR_UID NCR_RCL /* fas366 part-uniq id */
283
284
285 /* status register #2 definitions (read only) */
286 #define NCR_STAT2 NCR_CCF
287 #define NCRFAS_STAT2_SEQCNT 0x01 /* Sequence counter bit 7-3 enabled */
288 #define NCRFAS_STAT2_FLATCHED 0x02 /* FIFO flags register latched */
289 #define NCRFAS_STAT2_CLATCHED 0x04 /* Xfer cntr & recommand ctr latched */
290 #define NCRFAS_STAT2_CACTIVE 0x08 /* Command register is active */
291 #define NCRFAS_STAT2_SCSI16 0x10 /* SCSI interface is wide */
292 #define NCRFAS_STAT2_ISHUTTLE 0x20 /* FIFO Top register contains 1 byte */
293 #define NCRFAS_STAT2_OSHUTTLE 0x40 /* next byte from FIFO is MSB */
294 #define NCRFAS_STAT2_EMPTY 0x80 /* FIFO is empty */
295
296 #endif /* _NCR53C9XREG_H_ */
Cache object: 05dbaefe769a0f028ee0877698d17f5f
|