FreeBSD/Linux Kernel Cross Reference
sys/dev/ic/i82801lpcreg.h

     /*      $NetBSD: i82801lpcreg.h,v 1.16 2022/09/22 14:45:33 riastradh Exp $      */
     
     /*-
      * Copyright (c) 2004 The NetBSD Foundation, Inc.
      * All rights reserved.
      *
      * This code is derived from software contributed to The NetBSD Foundation
      * by Minoura Makoto.
      *
     * Redistribution and use in source and binary forms, with or without
     * modification, are permitted provided that the following conditions
     * are met:
     * 1. Redistributions of source code must retain the above copyright
     *    notice, this list of conditions and the following disclaimer.
     * 2. Redistributions in binary form must reproduce the above copyright
     *    notice, this list of conditions and the following disclaimer in the
     *    documentation and/or other materials provided with the distribution.
     *
     * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
     * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
     * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
     * PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
     * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
     * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
     * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
     * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
     * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
     * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
     * POSSIBILITY OF SUCH DAMAGE.
     */
    
    /*
     * Intel 82801 Series I/O Controller Hub (ICH) -- LPC Interface Bridge part
     *   register definitions.
     */
    
    #ifndef _DEV_IC_I82801LPCREG_H_
    #define _DEV_IC_I82801LPCREG_H_
    /*
     * PCI configuration registers
     */
    #define LPCIB_PCI_PMBASE        0x40
    #define LPCIB_PCI_PM_SIZE       0x00000080
    #define LPCIB_PCI_ACPI_CNTL     0x44
    # define LPCIB_PCI_ACPI_CNTL_EN (1 << 4)
    /* GPIO config registers ICH6+ */
    #define LPCIB_PCI_GPIO_BASE_ICH6        0x48
    #define LPCIB_PCI_GPIO_CNTL_ICH6        0x4c
    #define LPCIB_PCI_BIOS_CNTL     0x4c /* actually 0x4e */
    #define LPCIB_PCI_BIOS_CNTL_BWE (0x0001 << 16) /* write enable */
    #define LPCIB_PCI_BIOS_CNTL_BLE (0x0002 << 16) /* lock enable */
    #define LPCIB_PCI_TCO_CNTL      0x54
    /* GPIO config registers ICH0-ICH5 */
    #define LPCIB_PCI_GPIO_BASE     0x58
    #define LPCIB_PCI_GPIO_SIZE     0x00000080
    #define LPCIB_PCI_GPIO_CNTL     0x5c
    #define LPCIB_PCI_GPIO_CNTL_EN  (1 << 4)
    #define LPCIB_PCI_PIRQA_ROUT    0x60
    #define LPCIB_PCI_PIRQB_ROUT    0x61
    #define LPCIB_PCI_PIRQC_ROUT    0x62
    #define LPCIB_PCI_PIRQD_ROUT    0x63
    #define LPCIB_PCI_SIRQ_CNTL     0x64
    #define LPCIB_PCI_PIRQE_ROUT    0x68
    #define LPCIB_PCI_PIRQF_ROUT    0x69
    #define LPCIB_PCI_PIRQG_ROUT    0x6a
    #define LPCIB_PCI_PIRQH_ROUT    0x6b
    #define LPCIB_PCI_D31_ERR_CFG   0x88
    #define LPCIB_PCI_D31_ERR_STS   0x8a
    #define LPCIB_PCI_PCI_DMA_C     0x90
    #define LPCIB_PCI_GEN_PMCON_1   0xa0
    # define LPCIB_PCI_GEN_PMCON_1_SS_EN    0x08
    #define LPCIB_PCI_GEN_PMCON_2   0xa2
    #define LPCIB_PCI_GEN_PMCON_3   0xa4
    #define LPCIB_PCI_STPCLK_DEL    0xa8
    #define LPCIB_PCI_GPI_ROUT      0xb8
    #define LPCIB_PCI_TRP_FWD_EN    0xc0
    #define LPCIB_PCI_MON4_TRP_RNG  0xc4
    #define LPCIB_PCI_MON5_TRP_RNG  0xc5
    #define LPCIB_PCI_MON6_TRP_RNG  0xc6
    #define LPCIB_PCI_MON7_TRP_RNG  0xc7
    #define LPCIB_PCI_MON_TRP_MSK   0xcc
    #define LPCIB_PCI_GEN_CNTL      0xd0
    #define LPCIB_ICH5_HPTC_EN              0x00020000
    #define LPCIB_ICH5_HPTC_WIN_MASK        0x0000c000
    #define LPCIB_ICH5_HPTC_0000            0x00000000
    #define LPCIB_ICH5_HPTC_0000_BASE       0xfed00000
    #define LPCIB_ICH5_HPTC_1000            0x00008000
    #define LPCIB_ICH5_HPTC_1000_BASE       0xfed01000
    #define LPCIB_ICH5_HPTC_2000            0x00010000
    #define LPCIB_ICH5_HPTC_2000_BASE       0xfed02000
    #define LPCIB_ICH5_HPTC_3000            0x00018000
    #define LPCIB_ICH5_HPTC_3000_BASE       0xfed03000
    #define LPCIB_PCI_GEN_STA       0xd4
    # define LPCIB_PCI_GEN_STA_SAFE_MODE    (1 << 2)
    # define LPCIB_PCI_GEN_STA_NO_REBOOT    (1 << 1)
    #define LPCIB_PCI_BACK_CNTL     0xd5
    #define LPCIB_PCI_RTC_CONF      0xd8
    #define LPCIB_PCI_COM_DEC       0xe0
    #define LPCIB_PCI_LPCFDD_DEC    0xe1
   #define LPCIB_PCI_SND_DEC       0xe2
   #define LPCIB_PCI_FWH_DEC_EN1   0xe3
   #define LPCIB_PCI_GEN1_DEC      0xe4
   #define LPCIB_PCI_LPC_EN        0xe6
   #define LPCIB_PCI_FWH_SEL1      0xe8
   #define LPCIB_PCI_GEN2_DEC      0xec
   #define LPCIB_PCI_FWH_SEL2      0xee
   #define LPCIB_PCI_FWH_DEC_EN2   0xf0
   #define LPCIB_PCI_FUNC_DIS      0xf2
   
   /*
    * Power management I/O registers
    *  (offset from PMBASE)
    */
   #define PMC_PM1_STS             0x00 /* ACPI PM1a_EVT_BLK fixed event status */
   #define PMC_PM1_EN              0x02 /* ACPI PM1a_EVT_BLK fixed event enable */
   #define PMC_PM1_CNT             0x04 /* ACPI PM1a_CNT_BLK */
   #define PMC_PM1_TMR             0x08 /* ACPI PMTMR_BLK power mgmt timer */
   #define PMC_PROC_CNT            0x10 /* ACPI P_BLK processor control */
   #define PMC_LV2                 0x14 /* ACPI P_BLK processor C2 control */
   #define PMC_PM_CTRL             0x20 /* ACPI Power Management Control */
   # define PMC_PM_SS_STATE_LOW            0x01 /* SpeedStep Low Power State */
   #define PMC_GPE0_STS            0x28 /* ACPI GPE0_BLK GPE0 status */
   #define PMC_GPE0_EN             0x2c /* ACPI GPE0_BLK GPE0 enable */
   #define PMC_SMI_EN              0x30
   # define PMC_SMI_EN_INTEL_USB2_EN       (1 << 18)
   # define PMC_SMI_EN_LEGACY_USB2_EN      (1 << 17)
   # define PMC_SMI_EN_PERIODIC_EN         (1 << 14)
   # define PMC_SMI_EN_TCO_EN              (1 << 13)
   # define PMC_SMI_EN_MCSMI_EN            (1 << 11)
   # define PMC_SMI_EN_BIOS_RLS            (1 << 7)
   # define PMC_SMI_EN_SWSMI_TMR_EN        (1 << 6)
   # define PMC_SMI_EN_APMC_EN             (1 << 5)
   # define PMC_SMI_EN_SLP_SMI_EN          (1 << 4)
   # define PMC_SMI_EN_LEGACY_USB_EN       (1 << 3)
   # define PMC_SMI_EN_BIOS_EN             (1 << 2)
   # define PMC_SMI_EN_EOS                 (1 << 1)
   # define PMC_SMI_EN_GBL_SMI_EN          (1 << 0)
   #define PMC_SMI_STS             0x34
   #define PMC_ALT_GP_SMI_EN       0x38
   #define PMC_ALT_GP_SMI_STS      0x3a
   #define PMC_MON_SMI             0x40
   #define PMC_DEVACT_STS          0x44
   #define PMC_DEVTRAP_EN          0x48
   #define PMC_BUS_ADDR_TRACK      0x4c
   #define PMC_BUS_CYC_TRACK       0x4e
   #define PMC_PM_SS_CNTL          0x50            /* SpeedStep control */
   # define PMC_PM_SS_CNTL_ARB_DIS         0x01    /* disable arbiter */
   #define PMC_TCO_BASE            0x60
   
   /*
    * General Purpose I/O Registers
    *  (offset from GPIO_BASE)
    */
   #define LPCIB_GPIO_GPIO_USE_SEL         0x00
   #define LPCIB_GPIO_GP_IO_SEL            0x04
   #define LPCIB_GPIO_GP_LVL               0x0c
   #define LPCIB_GPIO_GPO_TTL              0x14
   #define LPCIB_GPIO_GPO_BLINK            0x18
   #define LPCIB_GPIO_GPI_INV              0x2c
   #define LPCIB_GPIO_GPIO_USE_SEL2        0x30
   #define LPCIB_GPIO_GP_IO_SEL2           0x34
   #define LPCIB_GPIO_GP_LVL2              0x38
   
   /*
    * SMBus controller registers.
    */
   
   /* PCI configuration registers */
   #define SMB_BASE        0x20            /* SMBus base address */
   #define SMB_HOSTC       0x40            /* host configuration */
   #define SMB_HOSTC_HSTEN         (1 << 0)        /* enable host controller */
   #define SMB_HOSTC_SMIEN         (1 << 1)        /* generate SMI */
   #define SMB_HOSTC_I2CEN         (1 << 2)        /* enable I2C commands */
   
   /* SMBus I/O registers */
   #define SMB_HS          0x00            /* host status */
   #define SMB_HS_BUSY             (1 << 0)        /* running a command */
   #define SMB_HS_INTR             (1 << 1)        /* command completed */
   #define SMB_HS_DEVERR           (1 << 2)        /* command error */
   #define SMB_HS_BUSERR           (1 << 3)        /* transaction collision */
   #define SMB_HS_FAILED           (1 << 4)        /* failed bus transaction */
   #define SMB_HS_SMBAL            (1 << 5)        /* SMBALERT# asserted */
   #define SMB_HS_INUSE            (1 << 6)        /* bus semaphore */
   #define SMB_HS_BDONE            (1 << 7)        /* byte received/transmitted */
   #define SMB_HS_BITS             "\020\001BUSY\002INTR\003DEVERR\004BUSERR\005FAILED\006SMBAL\007INUSE\010BDONE"
   #define SMB_HC          0x02            /* host control */
   #define SMB_HC_INTREN           (1 << 0)        /* enable interrupts */
   #define SMB_HC_KILL             (1 << 1)        /* kill current transaction */
   #define SMB_HC_CMD_QUICK        (0 << 2)        /* QUICK command */
   #define SMB_HC_CMD_BYTE         (1 << 2)        /* BYTE command */
   #define SMB_HC_CMD_BDATA        (2 << 2)        /* BYTE DATA command */
   #define SMB_HC_CMD_WDATA        (3 << 2)        /* WORD DATA command */
   #define SMB_HC_CMD_PCALL        (4 << 2)        /* PROCESS CALL command */
   #define SMB_HC_CMD_BLOCK        (5 << 2)        /* BLOCK command */
   #define SMB_HC_CMD_I2CREAD      (6 << 2)        /* I2C READ command */
   #define SMB_HC_CMD_BLOCKP       (7 << 2)        /* BLOCK PROCESS command */
   #define SMB_HC_LASTB            (1 << 5)        /* last byte in block */
   #define SMB_HC_START            (1 << 6)        /* start transaction */
   #define SMB_HC_PECEN            (1 << 7)        /* enable PEC */
   #define SMB_HCMD        0x03            /* host command */
   #define SMB_TXSLVA      0x04            /* transmit slave address */
   #define SMB_TXSLVA_READ         (1 << 0)        /* read direction */
   #define SMB_TXSLVA_ADDR(x)      (((x) & 0x7f) << 1) /* 7-bit address */
   #define SMB_HD0         0x05            /* host data 0 */
   #define SMB_HD1         0x06            /* host data 1 */
   #define SMB_HBDB        0x07            /* host block data byte */
   #define SMB_PEC         0x08            /* PEC data */
   #define SMB_RXSLVA      0x09            /* receive slave address */
   #define SMB_SD          0x0a            /* receive slave data */
   #define SMB_SD_MSG0(x)          ((x) & 0xff)    /* data message byte 0 */
   #define SMB_SD_MSG1(x)          ((x) >> 8)      /* data message byte 1 */
   #define SMB_AS          0x0c            /* auxiliary status */
   #define SMB_AS_CRCE             (1 << 0)        /* CRC error */
   #define SMB_AS_TCO              (1 << 1)        /* advanced TCO mode */
   #define SMB_AC          0x0d            /* auxiliary control */
   #define SMB_AC_AAC              (1 << 0)        /* automatically append CRC */
   #define SMB_AC_E32B             (1 << 1)        /* enable 32-byte buffer */
   #define SMB_SMLPC       0x0e            /* SMLink pin control */
   #define SMB_SMLPC_LINK0         (1 << 0)        /* SMLINK0 pin state */
   #define SMB_SMLPC_LINK1         (1 << 1)        /* SMLINK1 pin state */
   #define SMB_SMLPC_CLKC          (1 << 2)        /* SMLINK0 pin is untouched */
   #define SMB_SMBPC       0x0f            /* SMBus pin control */
   #define SMB_SMBPC_CLK           (1 << 0)        /* SMBCLK pin state */
   #define SMB_SMBPC_DATA          (1 << 1)        /* SMBDATA pin state */
   #define SMB_SMBPC_CLKC          (1 << 2)        /* SMBCLK pin is untouched */
   #define SMB_SS          0x10            /* slave status */
   #define SMB_SS_HN               (1 << 0)        /* Host Notify command */
   #define SMB_SCMD        0x11            /* slave command */
   #define SMB_SCMD_INTREN         (1 << 0)        /* enable interrupts on HN */
   #define SMB_SCMD_WKEN           (1 << 1)        /* wake on HN */
   #define SMB_SCMD_SMBALDS        (1 << 2)        /* disable SMBALERT# intr */
   #define SMB_NDADDR      0x14            /* notify device address */
   #define SMB_NDADDR_ADDR(x)      ((x) >> 1)      /* 7-bit address */
   #define SMB_NDLOW       0x16            /* notify data low byte */
   #define SMB_NDHIGH      0x17            /* notify data high byte */
   
   /* ICH Chipset Configuration Registers (ICH6 and newer) */
   #define LPCIB_RCBA              0xf0
   #define LPCIB_RCBA_EN           0x00000001
   #define LPCIB_RCBA_SIZE         0x00004000
   #define LPCIB_GCS_OFFSET                0x3410
   #define LPCIB_GCS_NO_REBOOT             0x20
   #define LPCIB_RCBA_HPTC                 0x00003404
   #define LPCIB_RCBA_HPTC_EN              0x00000080
   #define LPCIB_RCBA_HPTC_WIN_MASK        0x00000003
   #define LPCIB_RCBA_HPTC_0000            0x00000000
   #define LPCIB_RCBA_HPTC_0000_BASE       0xfed00000
   #define LPCIB_RCBA_HPTC_1000            0x00000001
   #define LPCIB_RCBA_HPTC_1000_BASE       0xfed01000
   #define LPCIB_RCBA_HPTC_2000            0x00000002
   #define LPCIB_RCBA_HPTC_2000_BASE       0xfed02000
   #define LPCIB_RCBA_HPTC_3000            0x00000003
   #define LPCIB_RCBA_HPTC_3000_BASE       0xfed03000
   
   /*
    * System management TCO registers
    */
   #define TCO_RLD                 0x00
   #define TCO_TMR                 0x01 /* ICH5 and older */
   # define TCO_TMR_MASK           0x3f
   #define TCO_DAT_IN              0x02
   #define TCO_DAT_OUT             0x03
   #define TCO1_STS                0x04
   # define TCO1_STS_TIMEOUT               0x08
   #define TCO2_STS                0x06
   # define TCO2_STS_BOOT_STS              0x04
   # define TCO2_STS_SECONDS_TO_STS        0x02
   #define TCO1_CNT                0x08
   # define TCO1_CNT_TCO_LOCK              (1 << 12)
   # define TCO1_CNT_TCO_TMR_HLT           (1 << 11)
   # define TCO1_CNT_SEND_NOW              (1 << 10)
   # define TCO1_CNT_NMI2SMI_EN            (1 << 9)
   # define TCO1_CNT_NMI_NOW               (1 << 8)
   #define TCO2_CNT                0x0a
   #define TCO_MESSAGE1            0x0c
   #define TCO_MESSAGE2            0x0d
   #define TCO_WDSTATUS            0x0e
   #define TCO_SW_IRQ_GEN          0x10
   #define TCO_TMR2                0x12 /* ICH6 and newer */
   #define TCO_REGSIZE             0x20
   
   /*
    * TCO timer tick.  ICH datasheets say:
    *  - The timer is clocked at approximately 0.6 seconds
    *  - 6 bit; values of 0-3 will be ignored and should not be attempted
    */
   static __inline int
   tcotimer_tick_to_second(int ltick)
   {
           return ltick * 6 / 10;
   }
   
   static __inline int
   tcotimer_second_to_tick(int ltick)
   {
           return ltick * 10 / 6;
   }
   
   #define TCOTIMER_MIN_TICK       4
   #define TCOTIMER2_MIN_TICK      2
   #define TCOTIMER_MAX_TICK       0x3f    /* 39 seconds max */
   #define TCOTIMER2_MAX_TICK      0x265   /* 613 seconds max */
   
   #endif /*  _DEV_IC_I82801LPCREG_H_ */

Cache object: cece6fe00127b36b92e0e23e544cc768