FreeBSD/Linux Kernel Cross Reference
sys/dev/mii/icsphyreg.h

     /*      $NetBSD: icsphyreg.h,v 1.2 2003/07/01 22:46:08 msaitoh Exp $    */
     
     /*-
      * Copyright (c) 1998 The NetBSD Foundation, Inc.
      * All rights reserved.
      *
      * This code is derived from software contributed to The NetBSD Foundation
      * by Jason R. Thorpe of the Numerical Aerospace Simulation Facility,
      * NASA Ames Research Center.
     *
     * Redistribution and use in source and binary forms, with or without
     * modification, are permitted provided that the following conditions
     * are met:
     * 1. Redistributions of source code must retain the above copyright
     *    notice, this list of conditions and the following disclaimer.
     * 2. Redistributions in binary form must reproduce the above copyright
     *    notice, this list of conditions and the following disclaimer in the
     *    documentation and/or other materials provided with the distribution.
     *
     * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
     * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
     * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
     * PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
     * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
     * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
     * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
     * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
     * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
     * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
     * POSSIBILITY OF SUCH DAMAGE.
     *
     * $FreeBSD$
     */
    
    #ifndef _DEV_MII_ICSPHYREG_H_
    #define _DEV_MII_ICSPHYREG_H_
    
    /*
     * ICS1890 registers.
     *      http://www.icst.com/pdf/18??.pdf
     */
    
    /* HEX                          1889    1890    1892    1893
     *--------------------------------------------------------------
     *  0 Control                   *       *       *       *
     *  1 Status                    *       *       *       *
     *  2 PHY Identifier            *       *       *       *
     *  3 PHY Identifier            *       *       *       *
     *  4 Auto-Neg. Advertisement           *       *       *
     *  5 Auto-Neg. Link Parent Adv         *       *       *
     *  6 Auto-Neg. Expansion               *       *       *
     *  7 Auto-Neg. Next Page Tx                    *       *
     *  8 ANg Nxt Page Lnk Parnt Abl                *       *
     * 10 Extended Control          *       *       *       *
     * 11 Quick Poll Status         *       *       *       *
     * 12 10Base-T Operation                *       *       *
     * 13 Extended Control2                 *       *       *
     */
    
    #define MII_ICSPHY_ECR          0x10    /* Extended Control Register */
    #define ECR_OVR                 0x8000  /* disable command reg overwrites */
    #define ECR_PHYADDR_MASK        0x07c0  /* PHY address mask */
    #define ECR_CTEST               0x0020  /* Stream Cipher Test Mode */
    #define ECR_IECT                0x0004  /* Invalid Error Code Test */
    #define ECR_SSD                 0x0001  /* Stream Cipher Disable */
    
    #define MII_ICSPHY_QPR          0x11    /* Quick Poll Register */
    #define QPR_SPEED               0x8000  /* 100Mbps */
    #define QPR_FDX                 0x4000  /* Full dupled */
    #define QPR_ANB2                0x2000  /* Autoneg monitor bit 2 */
    #define QPR_ANB1                0x1000  /* Autoneg monitor bit 1 */
    #define QPR_ANB0                0x0800  /* Autoneg monitor bit 0 */
    #define QPR_RXERR               0x0400  /* Receive signal lost */
    #define QPR_PLLERR              0x0200  /* PLL error */
    #define QPR_FCARR               0x0100  /* False carrier detected */
    #define QPR_INVALSYM            0x0080  /* Invalid Symbol Detected */
    #define QPR_HALT                0x0040  /* Halt Symbol Detected */
    #define QPR_PREEM               0x0020  /* Two Idle Symbols together */
    #define QPR_ACOMP               0x0010  /* Autonegotiation complete */
    #define QPR_SDETECT             0x0008  /* signal detect */
    #define QPR_JABBER              0x0004  /* Jabber detected */
    #define QPR_RFAULT              0x0002  /* Remote Fault */
    #define QPR_LINK                0x0001  /* Link */
    
    #define MII_ICSPHY_TTR          0x12    /* 10baseT Operations Register */
    #define TTR_RJABBER             0x8000  /* Remote Jabber */
    #define TTR_POLARITY            0x4000  /* Polarity Reversed */
    #define TTR_NOJABBER            0x0020  /* Disable Jabber Check */
    #define TTR_LOOP                0x0010  /* Loopback mode */
    #define TTR_NOAPOLARITY         0x0008  /* Disable auto polarity correction */
    #define TTR_NOSQE               0x0004  /* Disable SQE check */
    #define TTR_NOLINK              0x0002  /* Disable Link check */
    #define TTR_NOSQUELCH           0x0001  /* Disable squelch */
    
    
    /*
     * Extended Control Register 2
     *
     * HEX                                  1889    1890    1892    1893
    *-------------------------------------------------------------------
    * 8000 Node/Repeater Mode                      *       *       *
    * 4000 Hardware/Software Mode                  *       *       *
    * 2000 Link Partner Support Remote Flt         *
    * 2000 Remote Fault                                    *       *
    * 1000
    * 0800
    * 0400 Xmitted Remote Fault status             *
    * 0200
    * 0100
    * 0080 Tri-state Enable                                        *
    * 0040
    * 0020
    * 0010 A-N Powerup Remote Flt                  *
    * 0008
    * 0004
    * 0002 Automatic 10Base-T Power Down                   *
    * 0001 Automatic 100Base-TX Power Down         *       *       *
    */
   
   #define MII_ICSPHY_ECR2         0x13    /* Extended Control Register 2 */
   #define ECR2_REPEATER           0x8000  /* Repeater Mode */
   #define ECR2_HWSW               0x4000  /* hw/sw config priority */
   #define ECR2_LPRF               0x2000  /* link partner supports rem fault */
   #define ECR2_FORCERF            0x0400  /* Force transmit of rem fault */
   #define ECR2_RFPUP              0x0010  /* A-N Powerup Remote fault */
   #define ECR2_10AUTOPWRDN        0x0002  /* Automatic 10baseT power down */
   #define ECR2_100AUTOPWRDN       0x0001  /* Automatic 100baseTX power down */
   
   #endif /* _DEV_MII_ICSPHYREG_H_ */

Cache object: b30a1826c6e5c37d61cf05b1bc692797