FreeBSD/Linux Kernel Cross Reference
sys/dev/mii/nsphyreg.h

     /*      $NetBSD: nsphyreg.h,v 1.1 1998/08/10 23:58:39 thorpej Exp $     */
     
     /*-
      * Copyright (c) 1998 The NetBSD Foundation, Inc.
      * All rights reserved.
      *
      * This code is derived from software contributed to The NetBSD Foundation
      * by Jason R. Thorpe of the Numerical Aerospace Simulation Facility,
      * NASA Ames Research Center.
     *
     * Redistribution and use in source and binary forms, with or without
     * modification, are permitted provided that the following conditions
     * are met:
     * 1. Redistributions of source code must retain the above copyright
     *    notice, this list of conditions and the following disclaimer.
     * 2. Redistributions in binary form must reproduce the above copyright
     *    notice, this list of conditions and the following disclaimer in the
     *    documentation and/or other materials provided with the distribution.
     *
     * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
     * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
     * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
     * PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
     * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
     * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
     * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
     * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
     * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
     * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
     * POSSIBILITY OF SUCH DAMAGE.
     *
     * $FreeBSD$
     */
    
    #ifndef _DEV_MII_NSPHYREG_H_
    #define _DEV_MII_NSPHYREG_H_
    
    /*
     * DP83840 registers.
     */
    
    #define MII_NSPHY_DCR           0x12    /* Disconnect counter */
    
    #define MII_NSPHY_FCSCR         0x13    /* False carrier sense counter */
    
    #define MII_NSPHY_RECR          0x15    /* Receive error counter */
    
    #define MII_NSPHY_SRR           0x16    /* Silicon revision */
    
    #define MII_NSPHY_PCR           0x17    /* PCS sub-layer configuration */
    #define PCR_NRZI                0x8000  /* NRZI encoding enabled for 100TX */
    #define PCR_DESCRTOSEL          0x4000  /* descrambler t/o select (2ms) */
    #define PCR_DESCRTODIS          0x2000  /* descrambler t/o disable */
    #define PCR_REPEATER            0x1000  /* repeater mode */
    #define PCR_ENCSEL              0x0800  /* encoder mode select */
    #define PCR_CLK25MDIS           0x0080  /* CLK25M disable */
    #define PCR_FLINK100            0x0040  /* force good link in 100mbps */
    #define PCR_CIMDIS              0x0020  /* carrier integrity monitor disable */
    #define PCR_TXOFF               0x0010  /* force transmit off */
    #define PCR_LED1MODE            0x0004  /* LED1 mode: see below */
    #define PCR_LED4MODE            0x0002  /* LED4 mode: see below */
    
    /*
     * LED1 Mode:
     *
     *      1       LED1 output configured to PAR's CON_STATUS, useful for
     *              network management in 100baseTX mode.
     *
     *      0       Normal LED1 operation - 10baseTX and 100baseTX transmission
     *              activity.
     *
     * LED4 Mode:
     *
     *      1       LED4 output configured to indicate full-duplex in both
     *              10baseT and 100baseTX modes.
     *
     *      0       LED4 output configured to indicate polarity in 10baseT
     *              mode and full-duplex in 100baseTX mode.
     */
    
    #define MII_NSPHY_LBREMR        0x18    /* Loopback, bypass, error mask */
    #define LBREMR_BADSSDEN         0x8000  /* enable bad SSD detection */
    #define LBREMR_BP4B5B           0x4000  /* bypass 4b/5b encoding */
    #define LBREMR_BPSCR            0x2000  /* bypass scrambler */
    #define LBREMR_BPALIGN          0x1000  /* bypass alignment function */
    #define LBREMR_10LOOP           0x0800  /* 10baseT loopback */
    #define LBREMR_LB1              0x0200  /* loopback ctl 1 */
    #define LBREMR_LB0              0x0100  /* loopback ctl 0 */
    #define LBREMR_ALTCRS           0x0040  /* alt crs operation */
    #define LBREMR_LOOPXMTDIS       0x0020  /* disable transmit in 100TX loopbk */
    #define LBREMR_CODEERR          0x0010  /* code errors */
    #define LBREMR_PEERR            0x0008  /* premature end errors */
    #define LBREMR_LINKERR          0x0004  /* link errors */
    #define LBREMR_PKTERR           0x0002  /* packet errors */
    
    #define MII_NSPHY_PAR           0x19    /* Physical address and status */
    #define PAR_DISCRSJAB           0x0800  /* disable car sense during jab */
    #define PAR_ANENSTAT            0x0400  /* autoneg mode status */
    #define PAR_FEFIEN              0x0100  /* far end fault enable */
   #define PAR_FDX                 0x0080  /* full duplex status */
   #define PAR_10                  0x0040  /* 10mbps mode */
   #define PAR_CON                 0x0020  /* connect status */
   #define PAR_AMASK               0x001f  /* PHY address bits */
   
   #define MII_NSPHY_10BTSR        0x1b    /* 10baseT status */
   #define MII_NSPHY_10BTCR        0x1c    /* 10baseT configuration */
   
   #endif /* _DEV_MII_NSPHYREG_H_ */

Cache object: c85e36469d509a2ce46586b49848e108