FreeBSD/Linux Kernel Cross Reference
sys/dev/sym/sym_defs.h

     /*-
      *  Device driver optimized for the Symbios/LSI 53C896/53C895A/53C1010 
      *  PCI-SCSI controllers.
      *
      *  Copyright (C) 1999-2001  Gerard Roudier <groudier@free.fr>
      *
      *  This driver also supports the following Symbios/LSI PCI-SCSI chips:
      *      53C810A, 53C825A, 53C860, 53C875, 53C876, 53C885, 53C895,
      *      53C810,  53C815,  53C825 and the 53C1510D is 53C8XX mode.
     *
     *  
     *  This driver for FreeBSD-CAM is derived from the Linux sym53c8xx driver.
     *  Copyright (C) 1998-1999  Gerard Roudier
     *
     *  The sym53c8xx driver is derived from the ncr53c8xx driver that had been 
     *  a port of the FreeBSD ncr driver to Linux-1.2.13.
     *
     *  The original ncr driver has been written for 386bsd and FreeBSD by
     *          Wolfgang Stanglmeier        <wolf@cologne.de>
     *          Stefan Esser                <se@mi.Uni-Koeln.de>
     *  Copyright (C) 1994  Wolfgang Stanglmeier
     *
     *  The initialisation code, and part of the code that addresses 
     *  FreeBSD-CAM services is based on the aic7xxx driver for FreeBSD-CAM 
     *  written by Justin T. Gibbs.
     *
     *  Other major contributions:
     *
     *  NVRAM detection and reading.
     *  Copyright (C) 1997 Richard Waltham <dormouse@farsrobt.demon.co.uk>
     *
     *-----------------------------------------------------------------------------
     *
     * Redistribution and use in source and binary forms, with or without
     * modification, are permitted provided that the following conditions
     * are met:
     * 1. Redistributions of source code must retain the above copyright
     *    notice, this list of conditions and the following disclaimer.
     * 2. Redistributions in binary form must reproduce the above copyright
     *    notice, this list of conditions and the following disclaimer in the
     *    documentation and/or other materials provided with the distribution.
     * 3. The name of the author may not be used to endorse or promote products
     *    derived from this software without specific prior written permission.
     *
     * THIS SOFTWARE IS PROVIDED BY THE AUTHORS AND CONTRIBUTORS ``AS IS'' AND
     * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
     * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
     * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
     * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
     * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
     * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
     * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
     * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
     * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
     * SUCH DAMAGE.
     */
    
    /* $FreeBSD: releng/8.3/sys/dev/sym/sym_defs.h 179029 2008-05-15 20:27:18Z marius $ */
    
    #ifndef SYM_DEFS_H
    #define SYM_DEFS_H
    
    /*
     *  Vendor.
     */
    #define PCI_VENDOR_NCR          0x1000
    
    /*
     *  PCI device identifier of SYMBIOS chips.
     */
    #define PCI_ID_SYM53C810        1
    #define PCI_ID_SYM53C810AP      5
    #define PCI_ID_SYM53C815        4
    #define PCI_ID_SYM53C820        2
    #define PCI_ID_SYM53C825        3
    #define PCI_ID_SYM53C860        6
    #define PCI_ID_SYM53C875        0xf
    #define PCI_ID_SYM53C875_2      0x8f
    #define PCI_ID_SYM53C885        0xd
    #define PCI_ID_SYM53C895        0xc
    #define PCI_ID_SYM53C896        0xb
    #define PCI_ID_SYM53C895A       0x12
    #define PCI_ID_LSI53C1010       0x20
    #define PCI_ID_LSI53C1010_2     0x21
    #define PCI_ID_LSI53C1510D      0xa
    
    /*
     *      SYM53C8XX device features descriptor.
     */
    struct sym_pci_chip {
            u_short device_id;
            unsigned short  revision_id;
            const char *name;
            u_char  burst_max;      /* log-base-2 of max burst */
            u_char  offset_max;
            u_char  nr_divisor;
            u_char  lp_probe_bit;
            u_int   features;
    #define FE_LED0         (1<<0)
   #define FE_WIDE         (1<<1)    /* Wide data transfers */
   #define FE_ULTRA        (1<<2)    /* Ultra speed 20Mtrans/sec */
   #define FE_ULTRA2       (1<<3)    /* Ultra 2 - 40 Mtrans/sec */
   #define FE_DBLR         (1<<4)    /* Clock doubler present */
   #define FE_QUAD         (1<<5)    /* Clock quadrupler present */
   #define FE_ERL          (1<<6)    /* Enable read line */
   #define FE_CLSE         (1<<7)    /* Cache line size enable */
   #define FE_WRIE         (1<<8)    /* Write & Invalidate enable */
   #define FE_ERMP         (1<<9)    /* Enable read multiple */
   #define FE_BOF          (1<<10)   /* Burst opcode fetch */
   #define FE_DFS          (1<<11)   /* DMA fifo size */
   #define FE_PFEN         (1<<12)   /* Prefetch enable */
   #define FE_LDSTR        (1<<13)   /* Load/Store supported */
   #define FE_RAM          (1<<14)   /* On chip RAM present */
   #define FE_CLK80        (1<<15)   /* Board clock is 80 MHz */
   #define FE_RAM8K        (1<<16)   /* On chip RAM sized 8Kb */
   #define FE_64BIT        (1<<17)   /* 64-bit PCI BUS interface */
   #define FE_IO256        (1<<18)   /* Requires full 256 bytes in PCI space */
   #define FE_NOPM         (1<<19)   /* Scripts handles phase mismatch */
   #define FE_LEDC         (1<<20)   /* Hardware control of LED */
   #define FE_ULTRA3       (1<<21)   /* Ultra 3 - 80 Mtrans/sec DT */
   #define FE_66MHZ        (1<<22)   /* 66MHz PCI support */
   #define FE_CRC          (1<<23)   /* CRC support */
   #define FE_DIFF         (1<<24)   /* SCSI HVD support */
   #define FE_DFBC         (1<<25)   /* Have DFBC register */
   #define FE_LCKFRQ       (1<<26)   /* Have LCKFRQ */
   #define FE_C10          (1<<27)   /* Various C10 core (mis)features */
   #define FE_U3EN         (1<<28)   /* U3EN bit usable */
   #define FE_DAC          (1<<29)   /* Support PCI DAC (64 bit addressing) */
   
   #define FE_CACHE_SET    (FE_ERL|FE_CLSE|FE_WRIE|FE_ERMP)
   #define FE_CACHE0_SET   (FE_CACHE_SET & ~FE_ERL)
   #define FE_SPECIAL_SET  (FE_CACHE_SET|FE_BOF|FE_DFS|FE_LDSTR|FE_PFEN|FE_RAM)
   };
   
   /*
    *      Symbios NVRAM data format
    */
   #define SYMBIOS_NVRAM_SIZE 368
   #define SYMBIOS_NVRAM_ADDRESS 0x100
   
   struct Symbios_nvram {
   /* Header 6 bytes */
           u_short type;           /* 0x0000 */
           u_short byte_count;     /* excluding header/trailer */
           u_short checksum;
   
   /* Controller set up 20 bytes */
           u_char  v_major;        /* 0x00 */
           u_char  v_minor;        /* 0x30 */
           u32     boot_crc;
           u_short flags;
   #define SYMBIOS_SCAM_ENABLE     (1)
   #define SYMBIOS_PARITY_ENABLE   (1<<1)
   #define SYMBIOS_VERBOSE_MSGS    (1<<2)
   #define SYMBIOS_CHS_MAPPING     (1<<3)
   #define SYMBIOS_NO_NVRAM        (1<<3)  /* ??? */
           u_short flags1;
   #define SYMBIOS_SCAN_HI_LO      (1)
           u_short term_state;
   #define SYMBIOS_TERM_CANT_PROGRAM       (0)
   #define SYMBIOS_TERM_ENABLED            (1)
   #define SYMBIOS_TERM_DISABLED           (2)
           u_short rmvbl_flags;
   #define SYMBIOS_RMVBL_NO_SUPPORT        (0)
   #define SYMBIOS_RMVBL_BOOT_DEVICE       (1)
   #define SYMBIOS_RMVBL_MEDIA_INSTALLED   (2)
           u_char  host_id;
           u_char  num_hba;        /* 0x04 */
           u_char  num_devices;    /* 0x10 */
           u_char  max_scam_devices;       /* 0x04 */
           u_char  num_valid_scam_devices; /* 0x00 */
           u_char  flags2;
   #define SYMBIOS_AVOID_BUS_RESET         (1<<2)
   
   /* Boot order 14 bytes * 4 */
           struct Symbios_host{
                   u_short type;           /* 4:8xx / 0:nok */
                   u_short device_id;      /* PCI device id */
                   u_short vendor_id;      /* PCI vendor id */
                   u_char  bus_nr;         /* PCI bus number */
                   u_char  device_fn;      /* PCI device/function number << 3*/
                   u_short word8;
                   u_short flags;
   #define SYMBIOS_INIT_SCAN_AT_BOOT       (1)
                   u_short io_port;        /* PCI io_port address */
           } host[4];
   
   /* Targets 8 bytes * 16 */
           struct Symbios_target {
                   u_char  flags;
   #define SYMBIOS_DISCONNECT_ENABLE       (1)
   #define SYMBIOS_SCAN_AT_BOOT_TIME       (1<<1)
   #define SYMBIOS_SCAN_LUNS               (1<<2)
   #define SYMBIOS_QUEUE_TAGS_ENABLED      (1<<3)
                   u_char  rsvd;
                   u_char  bus_width;      /* 0x08/0x10 */
                   u_char  sync_offset;
                   u_short sync_period;    /* 4*period factor */
                   u_short timeout;
           } target[16];
   /* Scam table 8 bytes * 4 */
           struct Symbios_scam {
                   u_short id;
                   u_short method;
   #define SYMBIOS_SCAM_DEFAULT_METHOD     (0)
   #define SYMBIOS_SCAM_DONT_ASSIGN        (1)
   #define SYMBIOS_SCAM_SET_SPECIFIC_ID    (2)
   #define SYMBIOS_SCAM_USE_ORDER_GIVEN    (3)
                   u_short status;
   #define SYMBIOS_SCAM_UNKNOWN            (0)
   #define SYMBIOS_SCAM_DEVICE_NOT_FOUND   (1)
   #define SYMBIOS_SCAM_ID_NOT_SET         (2)
   #define SYMBIOS_SCAM_ID_VALID           (3)
                   u_char  target_id;
                   u_char  rsvd;
           } scam[4];
   
           u_char  spare_devices[15*8];
           u_char  trailer[6];             /* 0xfe 0xfe 0x00 0x00 0x00 0x00 */
   };
   typedef struct Symbios_nvram    Symbios_nvram;
   typedef struct Symbios_host     Symbios_host;
   typedef struct Symbios_target   Symbios_target;
   typedef struct Symbios_scam     Symbios_scam;
   
   /*
    *      Tekram NvRAM data format.
    */
   #define TEKRAM_NVRAM_SIZE 64
   #define TEKRAM_93C46_NVRAM_ADDRESS 0
   #define TEKRAM_24C16_NVRAM_ADDRESS 0x40
   
   struct Tekram_nvram {
           struct Tekram_target {
                   u_char  flags;
   #define TEKRAM_PARITY_CHECK             (1)
   #define TEKRAM_SYNC_NEGO                (1<<1)
   #define TEKRAM_DISCONNECT_ENABLE        (1<<2)
   #define TEKRAM_START_CMD                (1<<3)
   #define TEKRAM_TAGGED_COMMANDS          (1<<4)
   #define TEKRAM_WIDE_NEGO                (1<<5)
                   u_char  sync_index;
                   u_short word2;
           } target[16];
           u_char  host_id;
           u_char  flags;
   #define TEKRAM_MORE_THAN_2_DRIVES       (1)
   #define TEKRAM_DRIVES_SUP_1GB           (1<<1)
   #define TEKRAM_RESET_ON_POWER_ON        (1<<2)
   #define TEKRAM_ACTIVE_NEGATION          (1<<3)
   #define TEKRAM_IMMEDIATE_SEEK           (1<<4)
   #define TEKRAM_SCAN_LUNS                (1<<5)
   #define TEKRAM_REMOVABLE_FLAGS          (3<<6)  /* 0: disable; 1: boot device; 2:all */
           u_char  boot_delay_index;
           u_char  max_tags_index;
           u_short flags1;
   #define TEKRAM_F2_F6_ENABLED            (1)
           u_short spare[29];
   };
   typedef struct Tekram_nvram     Tekram_nvram;
   typedef struct Tekram_target    Tekram_target;
   
   /*
    *      SYM53C8XX IO register data structure.
    */
   struct sym_reg {
   /*00*/  u8      nc_scntl0;      /* full arb., ena parity, par->ATN  */
   
   /*01*/  u8      nc_scntl1;      /* no reset                         */
           #define   ISCON   0x10  /* connected to scsi                */
           #define   CRST    0x08  /* force reset                      */
           #define   IARB    0x02  /* immediate arbitration            */
   
   /*02*/  u8      nc_scntl2;      /* no disconnect expected           */
           #define   SDU     0x80  /* cmd: disconnect will raise error */
           #define   CHM     0x40  /* sta: chained mode                */
           #define   WSS     0x08  /* sta: wide scsi send           [W]*/
           #define   WSR     0x01  /* sta: wide scsi received       [W]*/
   
   /*03*/  u8      nc_scntl3;      /* cnf system clock dependent       */
           #define   EWS     0x08  /* cmd: enable wide scsi         [W]*/
           #define   ULTRA   0x80  /* cmd: ULTRA enable                */
                                   /* bits 0-2, 7 rsvd for C1010       */
   
   /*04*/  u8      nc_scid;        /* cnf host adapter scsi address    */
           #define   RRE     0x40  /* r/w:e enable response to resel.  */
           #define   SRE     0x20  /* r/w:e enable response to select  */
   
   /*05*/  u8      nc_sxfer;       /* ### Sync speed and count         */
                                   /* bits 6-7 rsvd for C1010          */
   
   /*06*/  u8      nc_sdid;        /* ### Destination-ID               */
   
   /*07*/  u8      nc_gpreg;       /* ??? IO-Pins                      */
   
   /*08*/  u8      nc_sfbr;        /* ### First byte received          */
   
   /*09*/  u8      nc_socl;
           #define   CREQ    0x80  /* r/w: SCSI-REQ                    */
           #define   CACK    0x40  /* r/w: SCSI-ACK                    */
           #define   CBSY    0x20  /* r/w: SCSI-BSY                    */
           #define   CSEL    0x10  /* r/w: SCSI-SEL                    */
           #define   CATN    0x08  /* r/w: SCSI-ATN                    */
           #define   CMSG    0x04  /* r/w: SCSI-MSG                    */
           #define   CC_D    0x02  /* r/w: SCSI-C_D                    */
           #define   CI_O    0x01  /* r/w: SCSI-I_O                    */
   
   /*0a*/  u8      nc_ssid;
   
   /*0b*/  u8      nc_sbcl;
   
   /*0c*/  u8      nc_dstat;
           #define   DFE     0x80  /* sta: dma fifo empty              */
           #define   MDPE    0x40  /* int: master data parity error    */
           #define   BF      0x20  /* int: script: bus fault           */
           #define   ABRT    0x10  /* int: script: command aborted     */
           #define   SSI     0x08  /* int: script: single step         */
           #define   SIR     0x04  /* int: script: interrupt instruct. */
           #define   IID     0x01  /* int: script: illegal instruct.   */
   
   /*0d*/  u8      nc_sstat0;
           #define   ILF     0x80  /* sta: data in SIDL register lsb   */
           #define   ORF     0x40  /* sta: data in SODR register lsb   */
           #define   OLF     0x20  /* sta: data in SODL register lsb   */
           #define   AIP     0x10  /* sta: arbitration in progress     */
           #define   LOA     0x08  /* sta: arbitration lost            */
           #define   WOA     0x04  /* sta: arbitration won             */
           #define   IRST    0x02  /* sta: scsi reset signal           */
           #define   SDP     0x01  /* sta: scsi parity signal          */
   
   /*0e*/  u8      nc_sstat1;
           #define   FF3210  0xf0  /* sta: bytes in the scsi fifo      */
   
   /*0f*/  u8      nc_sstat2;
           #define   ILF1    0x80  /* sta: data in SIDL register msb[W]*/
           #define   ORF1    0x40  /* sta: data in SODR register msb[W]*/
           #define   OLF1    0x20  /* sta: data in SODL register msb[W]*/
           #define   DM      0x04  /* sta: DIFFSENS mismatch (895/6 only) */
           #define   LDSC    0x02  /* sta: disconnect & reconnect      */
   
   /*10*/  u8      nc_dsa;         /* --> Base page                    */
   /*11*/  u8      nc_dsa1;
   /*12*/  u8      nc_dsa2;
   /*13*/  u8      nc_dsa3;
   
   /*14*/  u8      nc_istat;       /* --> Main Command and status      */
           #define   CABRT   0x80  /* cmd: abort current operation     */
           #define   SRST    0x40  /* mod: reset chip                  */
           #define   SIGP    0x20  /* r/w: message from host to script */
           #define   SEM     0x10  /* r/w: message between host + script  */
           #define   CON     0x08  /* sta: connected to scsi           */
           #define   INTF    0x04  /* sta: int on the fly (reset by wr)*/
           #define   SIP     0x02  /* sta: scsi-interrupt              */
           #define   DIP     0x01  /* sta: host/script interrupt       */
   
   /*15*/  u8      nc_istat1;      /* 896 only */
   /*16*/  u8      nc_mbox0;       /* 896 only */
   /*17*/  u8      nc_mbox1;       /* 896 only */
   
   /*18*/  u8      nc_ctest0;
   /*19*/  u8      nc_ctest1;
   
   /*1a*/  u8      nc_ctest2;
           #define   CSIGP   0x40
                                   /* bits 0-2,7 rsvd for C1010        */
   
   /*1b*/  u8      nc_ctest3;
           #define   FLF     0x08  /* cmd: flush dma fifo              */
           #define   CLF     0x04  /* cmd: clear dma fifo              */
           #define   FM      0x02  /* mod: fetch pin mode              */
           #define   WRIE    0x01  /* mod: write and invalidate enable */
                                   /* bits 4-7 rsvd for C1010          */
   
   /*1c*/  u32     nc_temp;        /* ### Temporary stack              */
   
   /*20*/  u8      nc_dfifo;
   /*21*/  u8      nc_ctest4;
           #define   BDIS    0x80  /* mod: burst disable               */
           #define   MPEE    0x08  /* mod: master parity error enable  */
   
   /*22*/  u8      nc_ctest5;
           #define   DFS     0x20  /* mod: dma fifo size               */
                                   /* bits 0-1, 3-7 rsvd for C1010     */
   
   /*23*/  u8      nc_ctest6;
   
   /*24*/  u32     nc_dbc;         /* ### Byte count and command       */
   /*28*/  u32     nc_dnad;        /* ### Next command register        */
   /*2c*/  u32     nc_dsp;         /* --> Script Pointer               */
   /*30*/  u32     nc_dsps;        /* --> Script pointer save/opcode#2 */
   
   /*34*/  u8      nc_scratcha;    /* Temporary register a            */
   /*35*/  u8      nc_scratcha1;
   /*36*/  u8      nc_scratcha2;
   /*37*/  u8      nc_scratcha3;
   
   /*38*/  u8      nc_dmode;
           #define   BL_2    0x80  /* mod: burst length shift value +2 */
           #define   BL_1    0x40  /* mod: burst length shift value +1 */
           #define   ERL     0x08  /* mod: enable read line            */
           #define   ERMP    0x04  /* mod: enable read multiple        */
           #define   BOF     0x02  /* mod: burst op code fetch         */
   
   /*39*/  u8      nc_dien;
   /*3a*/  u8      nc_sbr;
   
   /*3b*/  u8      nc_dcntl;       /* --> Script execution control     */
           #define   CLSE    0x80  /* mod: cache line size enable      */
           #define   PFF     0x40  /* cmd: pre-fetch flush             */
           #define   PFEN    0x20  /* mod: pre-fetch enable            */
           #define   SSM     0x10  /* mod: single step mode            */
           #define   IRQM    0x08  /* mod: irq mode (1 = totem pole !) */
           #define   STD     0x04  /* cmd: start dma mode              */
           #define   IRQD    0x02  /* mod: irq disable                 */
           #define   NOCOM   0x01  /* cmd: protect sfbr while reselect */
                                   /* bits 0-1 rsvd for C1010          */
   
   /*3c*/  u32     nc_adder;
   
   /*40*/  u16     nc_sien;        /* -->: interrupt enable            */
   /*42*/  u16     nc_sist;        /* <--: interrupt status            */
           #define   SBMC    0x1000/* sta: SCSI Bus Mode Change (895/6 only) */
           #define   STO     0x0400/* sta: timeout (select)            */
           #define   GEN     0x0200/* sta: timeout (general)           */
           #define   HTH     0x0100/* sta: timeout (handshake)         */
           #define   MA      0x80  /* sta: phase mismatch              */
           #define   CMP     0x40  /* sta: arbitration complete        */
           #define   SEL     0x20  /* sta: selected by another device  */
           #define   RSL     0x10  /* sta: reselected by another device*/
           #define   SGE     0x08  /* sta: gross error (over/underflow)*/
           #define   UDC     0x04  /* sta: unexpected disconnect       */
           #define   RST     0x02  /* sta: scsi bus reset detected     */
           #define   PAR     0x01  /* sta: scsi parity error           */
   
   /*44*/  u8      nc_slpar;
   /*45*/  u8      nc_swide;
   /*46*/  u8      nc_macntl;
   /*47*/  u8      nc_gpcntl;
   /*48*/  u8      nc_stime0;      /* cmd: timeout for select&handshake*/
   /*49*/  u8      nc_stime1;      /* cmd: timeout user defined        */
   /*4a*/  u16     nc_respid;      /* sta: Reselect-IDs                */
   
   /*4c*/  u8      nc_stest0;
   
   /*4d*/  u8      nc_stest1;
           #define   SCLK    0x80  /* Use the PCI clock as SCSI clock      */
           #define   DBLEN   0x08  /* clock doubler running                */
           #define   DBLSEL  0x04  /* clock doubler selected               */
     
   
   /*4e*/  u8      nc_stest2;
           #define   ROF     0x40  /* reset scsi offset (after gross error!) */
           #define   EXT     0x02  /* extended filtering                     */
   
   /*4f*/  u8      nc_stest3;
           #define   TE     0x80   /* c: tolerAnt enable */
           #define   HSC    0x20   /* c: Halt SCSI Clock */
           #define   CSF    0x02   /* c: clear scsi fifo */
   
   /*50*/  u16     nc_sidl;        /* Lowlevel: latched from scsi data */
   /*52*/  u8      nc_stest4;
           #define   SMODE  0xc0   /* SCSI bus mode      (895/6 only) */
           #define    SMODE_HVD 0x40       /* High Voltage Differential       */
           #define    SMODE_SE  0x80       /* Single Ended                    */
           #define    SMODE_LVD 0xc0       /* Low Voltage Differential        */
           #define   LCKFRQ 0x20   /* Frequency Lock (895/6 only)     */
                                   /* bits 0-5 rsvd for C1010         */
   
   /*53*/  u8      nc_53_;
   /*54*/  u16     nc_sodl;        /* Lowlevel: data out to scsi data  */
   /*56*/  u8      nc_ccntl0;      /* Chip Control 0 (896)             */
           #define   ENPMJ  0x80   /* Enable Phase Mismatch Jump       */
           #define   PMJCTL 0x40   /* Phase Mismatch Jump Control      */
           #define   ENNDJ  0x20   /* Enable Non Data PM Jump          */
           #define   DISFC  0x10   /* Disable Auto FIFO Clear          */
           #define   DILS   0x02   /* Disable Internal Load/Store      */
           #define   DPR    0x01   /* Disable Pipe Req                 */
   
   /*57*/  u8      nc_ccntl1;      /* Chip Control 1 (896)             */
           #define   ZMOD   0x80   /* High Impedance Mode              */
           #define   DDAC   0x08   /* Disable Dual Address Cycle       */
           #define   XTIMOD 0x04   /* 64-bit Table Ind. Indexing Mode  */
           #define   EXTIBMV 0x02  /* Enable 64-bit Table Ind. BMOV    */
           #define   EXDBMV 0x01   /* Enable 64-bit Direct BMOV        */
   
   /*58*/  u16     nc_sbdl;        /* Lowlevel: data from scsi data    */
   /*5a*/  u16     nc_5a_;
   
   /*5c*/  u8      nc_scr0;        /* Working register B               */
   /*5d*/  u8      nc_scr1;
   /*5e*/  u8      nc_scr2;
   /*5f*/  u8      nc_scr3;
   
   /*60*/  u8      nc_scrx[64];    /* Working register C-R             */
   /*a0*/  u32     nc_mmrs;        /* Memory Move Read Selector        */
   /*a4*/  u32     nc_mmws;        /* Memory Move Write Selector       */
   /*a8*/  u32     nc_sfs;         /* Script Fetch Selector            */
   /*ac*/  u32     nc_drs;         /* DSA Relative Selector            */
   /*b0*/  u32     nc_sbms;        /* Static Block Move Selector       */
   /*b4*/  u32     nc_dbms;        /* Dynamic Block Move Selector      */
   /*b8*/  u32     nc_dnad64;      /* DMA Next Address 64              */
   /*bc*/  u16     nc_scntl4;      /* C1010 only                       */
           #define   U3EN    0x80  /* Enable Ultra 3                   */
           #define   AIPCKEN 0x40  /* AIP checking enable              */
                                   /* Also enable AIP generation on C10-33*/
           #define   XCLKH_DT 0x08 /* Extra clock of data hold on DT edge */
           #define   XCLKH_ST 0x04 /* Extra clock of data hold on ST edge */
           #define   XCLKS_DT 0x02 /* Extra clock of data set  on DT edge */
           #define   XCLKS_ST 0x01 /* Extra clock of data set  on ST edge */
   /*be*/  u8      nc_aipcntl0;    /* AIP Control 0 C1010 only         */
   /*bf*/  u8      nc_aipcntl1;    /* AIP Control 1 C1010 only         */
           #define DISAIP  0x08    /* Disable AIP generation C10-66 only  */
   /*c0*/  u32     nc_pmjad1;      /* Phase Mismatch Jump Address 1    */
   /*c4*/  u32     nc_pmjad2;      /* Phase Mismatch Jump Address 2    */
   /*c8*/  u8      nc_rbc;         /* Remaining Byte Count             */
   /*c9*/  u8      nc_rbc1;
   /*ca*/  u8      nc_rbc2;
   /*cb*/  u8      nc_rbc3;
   
   /*cc*/  u8      nc_ua;          /* Updated Address                  */
   /*cd*/  u8      nc_ua1;
   /*ce*/  u8      nc_ua2;
   /*cf*/  u8      nc_ua3;
   /*d0*/  u32     nc_esa;         /* Entry Storage Address            */
   /*d4*/  u8      nc_ia;          /* Instruction Address              */
   /*d5*/  u8      nc_ia1;
   /*d6*/  u8      nc_ia2;
   /*d7*/  u8      nc_ia3;
   /*d8*/  u32     nc_sbc;         /* SCSI Byte Count (3 bytes only)   */
   /*dc*/  u32     nc_csbc;        /* Cumulative SCSI Byte Count       */
                                   /* Following for C1010 only         */
   /*e0*/  u16    nc_crcpad;       /* CRC Value                        */
   /*e2*/  u8     nc_crccntl0;     /* CRC control register             */
           #define   SNDCRC  0x10  /* Send CRC Request                 */
   /*e3*/  u8     nc_crccntl1;     /* CRC control register             */
   /*e4*/  u32    nc_crcdata;      /* CRC data register                */
   /*e8*/  u32    nc_e8_;
   /*ec*/  u32    nc_ec_;
   /*f0*/  u16    nc_dfbc;         /* DMA FIFO byte count              */ 
   };
   
   /*-----------------------------------------------------------
    *
    *      Utility macros for the script.
    *
    *-----------------------------------------------------------
    */
   
   #define REGJ(p,r) (offsetof(struct sym_reg, p ## r))
   #define REG(r) REGJ (nc_, r)
   
   typedef u32 symcmd;
   
   /*-----------------------------------------------------------
    *
    *      SCSI phases
    *
    *-----------------------------------------------------------
    */
   
   #define SCR_DATA_OUT    0x00000000
   #define SCR_DATA_IN     0x01000000
   #define SCR_COMMAND     0x02000000
   #define SCR_STATUS      0x03000000
   #define SCR_DT_DATA_OUT 0x04000000
   #define SCR_DT_DATA_IN  0x05000000
   #define SCR_MSG_OUT     0x06000000
   #define SCR_MSG_IN      0x07000000
   /* DT phases are illegal for non Ultra3 mode */
   #define SCR_ILG_OUT     0x04000000
   #define SCR_ILG_IN      0x05000000
   
   /*-----------------------------------------------------------
    *
    *      Data transfer via SCSI.
    *
    *-----------------------------------------------------------
    *
    *      MOVE_ABS (LEN)
    *      <<start address>>
    *
    *      MOVE_IND (LEN)
    *      <<dnad_offset>>
    *
    *      MOVE_TBL
    *      <<dnad_offset>>
    *
    *-----------------------------------------------------------
    */
   
   #define OPC_MOVE          0x08000000
   
   #define SCR_MOVE_ABS(l) ((0x00000000 | OPC_MOVE) | (l))
   #define SCR_MOVE_IND(l) ((0x20000000 | OPC_MOVE) | (l))
   #define SCR_MOVE_TBL     (0x10000000 | OPC_MOVE)
   
   #define SCR_CHMOV_ABS(l) ((0x00000000) | (l))
   #define SCR_CHMOV_IND(l) ((0x20000000) | (l))
   #define SCR_CHMOV_TBL     (0x10000000)
   
   struct sym_tblmove {
           u32  size;
           u32  addr;
   };
   
   /*-----------------------------------------------------------
    *
    *      Selection
    *
    *-----------------------------------------------------------
    *
    *      SEL_ABS | SCR_ID (0..15)    [ | REL_JMP]
    *      <<alternate_address>>
    *
    *      SEL_TBL | << dnad_offset>>  [ | REL_JMP]
    *      <<alternate_address>>
    *
    *-----------------------------------------------------------
    */
   
   #define SCR_SEL_ABS     0x40000000
   #define SCR_SEL_ABS_ATN 0x41000000
   #define SCR_SEL_TBL     0x42000000
   #define SCR_SEL_TBL_ATN 0x43000000
   
   struct sym_tblsel {
           u_char  sel_scntl4;     /* C1010 only */
           u_char  sel_sxfer;
           u_char  sel_id;
           u_char  sel_scntl3;
   };
   
   #define SCR_JMP_REL     0x04000000
   #define SCR_ID(id)      (((u32)(id)) << 16)
   
   /*-----------------------------------------------------------
    *
    *      Waiting for Disconnect or Reselect
    *
    *-----------------------------------------------------------
    *
    *      WAIT_DISC
    *      dummy: <<alternate_address>>
    *
    *      WAIT_RESEL
    *      <<alternate_address>>
    *
    *-----------------------------------------------------------
    */
   
   #define SCR_WAIT_DISC   0x48000000
   #define SCR_WAIT_RESEL  0x50000000
   
   /*-----------------------------------------------------------
    *
    *      Bit Set / Reset
    *
    *-----------------------------------------------------------
    *
    *      SET (flags {|.. })
    *
    *      CLR (flags {|.. })
    *
    *-----------------------------------------------------------
    */
   
   #define SCR_SET(f)     (0x58000000 | (f))
   #define SCR_CLR(f)     (0x60000000 | (f))
   
   #define SCR_CARRY       0x00000400
   #define SCR_TRG         0x00000200
   #define SCR_ACK         0x00000040
   #define SCR_ATN         0x00000008
   
   
   /*-----------------------------------------------------------
    *
    *      Memory to memory move
    *
    *-----------------------------------------------------------
    *
    *      COPY (bytecount)
    *      << source_address >>
    *      << destination_address >>
    *
    *      SCR_COPY   sets the NO FLUSH option by default.
    *      SCR_COPY_F does not set this option.
    *
    *      For chips which do not support this option,
    *      sym_copy_and_bind() will remove this bit.
    *
    *-----------------------------------------------------------
    */
   
   #define SCR_NO_FLUSH 0x01000000
   
   #define SCR_COPY(n) (0xc0000000 | SCR_NO_FLUSH | (n))
   #define SCR_COPY_F(n) (0xc0000000 | (n))
   
   /*-----------------------------------------------------------
    *
    *      Register move and binary operations
    *
    *-----------------------------------------------------------
    *
    *      SFBR_REG (reg, op, data)        reg  = SFBR op data
    *      << 0 >>
    *
    *      REG_SFBR (reg, op, data)        SFBR = reg op data
    *      << 0 >>
    *
    *      REG_REG  (reg, op, data)        reg  = reg op data
    *      << 0 >>
    *
    *-----------------------------------------------------------
    *
    *      On 825A, 875, 895 and 896 chips the content 
    *      of SFBR register can be used as data (SCR_SFBR_DATA).
    *      The 896 has additionnal IO registers starting at 
    *      offset 0x80. Bit 7 of register offset is stored in 
    *      bit 7 of the SCRIPTS instruction first DWORD.
    *
    *-----------------------------------------------------------
    */
   
   #define SCR_REG_OFS(ofs) ((((ofs) & 0x7f) << 16ul) + ((ofs) & 0x80)) 
   
   #define SCR_SFBR_REG(reg,op,data) \
           (0x68000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
   
   #define SCR_REG_SFBR(reg,op,data) \
           (0x70000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
   
   #define SCR_REG_REG(reg,op,data) \
           (0x78000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
   
   
   #define      SCR_LOAD   0x00000000
   #define      SCR_SHL    0x01000000
   #define      SCR_OR     0x02000000
   #define      SCR_XOR    0x03000000
   #define      SCR_AND    0x04000000
   #define      SCR_SHR    0x05000000
   #define      SCR_ADD    0x06000000
   #define      SCR_ADDC   0x07000000
   
   #define      SCR_SFBR_DATA   (0x00800000>>8ul)  /* Use SFBR as data */
   
   /*-----------------------------------------------------------
    *
    *      FROM_REG (reg)            SFBR = reg
    *      << 0 >>
    *
    *      TO_REG   (reg)            reg  = SFBR
    *      << 0 >>
    *
    *      LOAD_REG (reg, data)      reg  = <data>
    *      << 0 >>
    *
    *      LOAD_SFBR(data)           SFBR = <data>
    *      << 0 >>
    *
    *-----------------------------------------------------------
    */
   
   #define SCR_FROM_REG(reg) \
           SCR_REG_SFBR(reg,SCR_OR,0)
   
   #define SCR_TO_REG(reg) \
           SCR_SFBR_REG(reg,SCR_OR,0)
   
   #define SCR_LOAD_REG(reg,data) \
           SCR_REG_REG(reg,SCR_LOAD,data)
   
   #define SCR_LOAD_SFBR(data) \
           (SCR_REG_SFBR (gpreg, SCR_LOAD, data))
   
   /*-----------------------------------------------------------
    *
    *      LOAD  from memory   to register.
    *      STORE from register to memory.
    *
    *      Only supported by 810A, 860, 825A, 875, 895 and 896.
    *
    *-----------------------------------------------------------
    *
    *      LOAD_ABS (LEN)
    *      <<start address>>
    *
    *      LOAD_REL (LEN)        (DSA relative)
    *      <<dsa_offset>>
    *
    *-----------------------------------------------------------
    */
   
   #define SCR_REG_OFS2(ofs) (((ofs) & 0xff) << 16ul)
   #define SCR_NO_FLUSH2   0x02000000
   #define SCR_DSA_REL2    0x10000000
   
   #define SCR_LOAD_R(reg, how, n) \
           (0xe1000000 | (how) | (SCR_REG_OFS2(REG(reg))) | (n))
   
   #define SCR_STORE_R(reg, how, n) \
           (0xe0000000 | (how) | (SCR_REG_OFS2(REG(reg))) | (n))
   
   #define SCR_LOAD_ABS(reg, n)    SCR_LOAD_R(reg, SCR_NO_FLUSH2, n)
   #define SCR_LOAD_REL(reg, n)    SCR_LOAD_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2, n)
   #define SCR_LOAD_ABS_F(reg, n)  SCR_LOAD_R(reg, 0, n)
   #define SCR_LOAD_REL_F(reg, n)  SCR_LOAD_R(reg, SCR_DSA_REL2, n)
   
   #define SCR_STORE_ABS(reg, n)   SCR_STORE_R(reg, SCR_NO_FLUSH2, n)
   #define SCR_STORE_REL(reg, n)   SCR_STORE_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2,n)
   #define SCR_STORE_ABS_F(reg, n) SCR_STORE_R(reg, 0, n)
   #define SCR_STORE_REL_F(reg, n) SCR_STORE_R(reg, SCR_DSA_REL2, n)
   
   
   /*-----------------------------------------------------------
    *
    *      Waiting for Disconnect or Reselect
    *
    *-----------------------------------------------------------
    *
    *      JUMP            [ | IFTRUE/IFFALSE ( ... ) ]
    *      <<address>>
    *
    *      JUMPR           [ | IFTRUE/IFFALSE ( ... ) ]
    *      <<distance>>
    *
    *      CALL            [ | IFTRUE/IFFALSE ( ... ) ]
    *      <<address>>
    *
    *      CALLR           [ | IFTRUE/IFFALSE ( ... ) ]
    *      <<distance>>
    *
    *      RETURN          [ | IFTRUE/IFFALSE ( ... ) ]
    *      <<dummy>>
    *
    *      INT             [ | IFTRUE/IFFALSE ( ... ) ]
    *      <<ident>>
    *
    *      INT_FLY         [ | IFTRUE/IFFALSE ( ... ) ]
    *      <<ident>>
    *
    *      Conditions:
    *           WHEN (phase)
    *           IF   (phase)
    *           CARRYSET
    *           DATA (data, mask)
    *
    *-----------------------------------------------------------
    */
   
   #define SCR_NO_OP       0x80000000
   #define SCR_JUMP        0x80080000
   #define SCR_JUMP64      0x80480000
   #define SCR_JUMPR       0x80880000
   #define SCR_CALL        0x88080000
   #define SCR_CALLR       0x88880000
   #define SCR_RETURN      0x90080000
   #define SCR_INT         0x98080000
   #define SCR_INT_FLY     0x98180000
   
   #define IFFALSE(arg)   (0x00080000 | (arg))
   #define IFTRUE(arg)    (0x00000000 | (arg))
   
   #define WHEN(phase)    (0x00030000 | (phase))
   #define IF(phase)      (0x00020000 | (phase))
   
   #define DATA(D)        (0x00040000 | ((D) & 0xff))
   #define MASK(D,M)      (0x00040000 | (((M ^ 0xff) & 0xff) << 8ul)|((D) & 0xff))
   
   #define CARRYSET       (0x00200000)
   
   /*-----------------------------------------------------------
    *
    *      SCSI  constants.
    *
    *-----------------------------------------------------------
    */
   
   /*
    *      Messages
    */
   
   #define M_COMPLETE      (0x00)
   #define M_EXTENDED      (0x01)
   #define M_SAVE_DP       (0x02)
   #define M_RESTORE_DP    (0x03)
   #define M_DISCONNECT    (0x04)
   #define M_ID_ERROR      (0x05)
   #define M_ABORT         (0x06)
   #define M_REJECT        (0x07)
   #define M_NOOP          (0x08)
   #define M_PARITY        (0x09)
   #define M_LCOMPLETE     (0x0a)
   #define M_FCOMPLETE     (0x0b)
   #define M_RESET         (0x0c)
   #define M_ABORT_TAG     (0x0d)
   #define M_CLEAR_QUEUE   (0x0e)
   #define M_INIT_REC      (0x0f)
   #define M_REL_REC       (0x10)
   #define M_TERMINATE     (0x11)
   #define M_SIMPLE_TAG    (0x20)
   #define M_HEAD_TAG      (0x21)
   #define M_ORDERED_TAG   (0x22)
   #define M_IGN_RESIDUE   (0x23)
   #define M_IDENTIFY      (0x80)
   
   #define M_X_MODIFY_DP   (0x00)
   #define M_X_SYNC_REQ    (0x01)
   #define M_X_WIDE_REQ    (0x03)
   #define M_X_PPR_REQ     (0x04)
   
   /*
    *      PPR protocol options
    */
   #define PPR_OPT_IU      (0x01)
   #define PPR_OPT_DT      (0x02)
   #define PPR_OPT_QAS     (0x04)
   #define PPR_OPT_MASK    (0x07)
   
   /*
    *      Status
    */
   
   #define S_GOOD          (0x00)
   #define S_CHECK_COND    (0x02)
   #define S_COND_MET      (0x04)
   #define S_BUSY          (0x08)
   #define S_INT           (0x10)
   #define S_INT_COND_MET  (0x14)
   #define S_CONFLICT      (0x18)
   #define S_TERMINATED    (0x20)
   #define S_QUEUE_FULL    (0x28)
   #define S_ILLEGAL       (0xff)
   
   #endif /* defined SYM_DEFS_H */

Cache object: 2dbeb526051fc61f2c0926885e4951c3