FreeBSD/Linux Kernel Cross Reference
sys/mips/conf/AP143.hints

     #
     # This file adds to the values in QCA953X_BASE.hints.
     #
     # $FreeBSD$
     
     # Embedded Atheros Switch
     hint.arswitch.0.at="mdio1"
     hint.arswitch.0.is_7240=0
     hint.arswitch.0.is_9340=1
    hint.arswitch.0.numphys=4
    hint.arswitch.0.phy4cpu=1       # phy 4 is a "CPU" separate PHY
    hint.arswitch.0.is_rgmii=0
    hint.arswitch.0.is_gmii=1       # arge1 <-> switch PHY is GMII
    
    # arge0 - MII, autoneg, phy(4)
    # MAC for arge0 is the first 6 bytes of the ART
    hint.arge.0.eeprommac=0x1fff0000
    hint.arge.0.phymask=0x10        # PHY4
    hint.arge.0.mdio=mdioproxy2     # .. off of the switch mdiobus
    
    # arge1 - GMII, 1000/full
    hint.arge.1.eeprommac=0x1fff0006
    hint.arge.1.phymask=0x0         # No directly mapped PHYs
    hint.arge.1.media=1000
    hint.arge.1.fduplex=1
    
    # Where the ART is - last 64k in the first 8MB of flash
    hint.ar71xx_caldata.0.map.0.ath_fixup_addr=0x1fff0000
    hint.ar71xx_caldata.0.map.0.ath_fixup_size=16384
    
    # And now tell the ath(4) driver where to look!
    hint.ath.0.eeprom_firmware="ar71xx_caldata.0.map.0.eeprom_firmware"
    
    # The AP121 4MB flash layout:
    #
    # bootargs=console=ttyS0,115200 root=31:02 rootfstype=squashfs
    #    init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),
    #    2752k(rootfs),896k(uImage),64k(NVRAM),64k(ART)
    #
    # So:
    # 256k: uboot
    # 64: uboot-env
    # 2752k: rootfs
    # 896k: kernel
    # 64k: config
    # 64k: ART
    
    hint.map.0.at="flash/spi0"
    hint.map.0.start=0x00000000
    hint.map.0.end=0x000040000
    hint.map.0.name="uboot"
    hint.map.0.readonly=1
    
    hint.map.1.at="flash/spi0"
    hint.map.1.start=0x00040000
    hint.map.1.end=0x00050000
    hint.map.1.name="uboot-env"
    hint.map.1.readonly=0
    
    hint.map.2.at="flash/spi0"
    hint.map.2.start=0x00050000
    hint.map.2.end=0x00300000
    hint.map.2.name="rootfs"
    hint.map.2.readonly=0
    
    hint.map.3.at="flash/spi0"
    hint.map.3.start=0x00300000
    hint.map.3.end=0x003e0000
    hint.map.3.name="kernel"
    hint.map.3.readonly=0
    
    hint.map.4.at="flash/spi0"
    hint.map.4.start=0x003e0000
    hint.map.4.end=0x003f0000
    hint.map.4.name="cfg"
    hint.map.4.readonly=0
    
    # This is radio calibration section.  It is (or should be!) unique
    # for each board, to take into account thermal and electrical differences
    # as well as the regulatory compliance data.
    #
    hint.map.5.at="flash/spi0"
    hint.map.5.start=0x003f0000
    hint.map.5.end=0x00400000
    hint.map.5.name="art"
    hint.map.5.readonly=1
    
    # GPIO specific configuration block
    
    # Don't flip on anything that isn't already enabled.
    # This includes leaving the SPI CS1/CS2 pins as GPIO pins as they're
    # not used here.
    hint.gpio.0.function_set=0x00000000
    hint.gpio.0.function_clear=0x00000000
    
    # These are the GPIO LEDs and buttons which can be software controlled.
    #hint.gpio.0.pinmask=0x001c02ae
    # hint.gpio.0.pinmask=0x00001803
    
   # gpio0 - WLAN LED
   # gpio1 - USB LED
   # gpio11 - Jumpstart button
   # gpio12 - Reset button
   
   # LEDs are configured separately and driven by the LED device
   #hint.gpioled.0.at="gpiobus0"
   #hint.gpioled.0.name="wlan"
   #hint.gpioled.0.pins=0x0001
   
   #hint.gpioled.1.at="gpiobus0"
   #hint.gpioled.1.name="usb"
   #hint.gpioled.1.pins=0x0002

Cache object: 0756df142bf3aa7c049d600b5052a7cd