Now available: The Design and Implementation of the FreeBSD Operating System (Second Edition)
[ source navigation ] [ diff markup ] [ identifier search ] [ freetext search ] [ file search ] [ list types ] [ track identifier ]
FreeBSD/Linux Kernel Cross Reference
sys/mips/conf/DB120.hints
Version:
- FREEBSD - FREEBSD-13-STABLE - FREEBSD-13-0 - FREEBSD-12-STABLE - FREEBSD-12-0 - FREEBSD-11-STABLE - FREEBSD-11-0 - FREEBSD-10-STABLE - FREEBSD-10-0 - FREEBSD-9-STABLE - FREEBSD-9-0 - FREEBSD-8-STABLE - FREEBSD-8-0 - FREEBSD-7-STABLE - FREEBSD-7-0 - FREEBSD-6-STABLE - FREEBSD-6-0 - FREEBSD-5-STABLE - FREEBSD-5-0 - FREEBSD-4-STABLE - FREEBSD-3-STABLE - FREEBSD22 - l41 - OPENBSD - linux-2.6 - MK84 - PLAN9 - xnu-8792
SearchContext: - none - 3 - 10
SearchContext: - none - 3 - 10
1 # $FreeBSD$ 2 3 # This is a placeholder until the hardware support is complete. 4 5 # mdiobus0 on arge0 6 hint.argemdio.0.at="nexus0" 7 hint.argemdio.0.maddr=0x19000000 8 hint.argemdio.0.msize=0x1000 9 hint.argemdio.0.order=0 10 11 # DB120 GMAC configuration 12 # + AR934X_ETH_CFG_RGMII_GMAC0 (1 << 0) 13 # + AR934X_ETH_CFG_SW_ONLY_MODE (1 << 6) 14 hint.ar934x_gmac.0.gmac_cfg=0x41 15 16 # GMAC0 here - connected to an AR8327 17 hint.arswitch.0.at="mdio0" 18 hint.arswitch.0.is_7240=0 19 hint.arswitch.0.is_9340=0 # not the internal switch! 20 hint.arswitch.0.numphys=5 21 hint.arswitch.0.phy4cpu=0 22 hint.arswitch.0.is_rgmii=1 23 hint.arswitch.0.is_gmii=0 24 25 # Other AR8327 configuration parameters 26 27 # AR8327_PAD_MAC_RGMII 28 hint.arswitch.0.pad.0.mode=6 29 hint.arswitch.0.pad.0.txclk_delay_en=1 30 hint.arswitch.0.pad.0.rxclk_delay_en=1 31 # AR8327_CLK_DELAY_SEL1 32 hint.arswitch.0.pad.0.txclk_delay_sel=1 33 # AR8327_CLK_DELAY_SEL2 34 hint.arswitch.0.pad.0.rxclk_delay_sel=2 35 36 # XXX there's no LED management just yet! 37 hint.arswitch.0.led.ctrl0=0x00000000 38 hint.arswitch.0.led.ctrl1=0xc737c737 39 hint.arswitch.0.led.ctrl2=0x00000000 40 hint.arswitch.0.led.ctrl3=0x00c30c00 41 hint.arswitch.0.led.open_drain=1 42 43 # force_link=1 is required for the rest of the parameters 44 # to be configured. 45 hint.arswitch.0.port.0.force_link=1 46 hint.arswitch.0.port.0.speed=1000 47 hint.arswitch.0.port.0.duplex=1 48 hint.arswitch.0.port.0.txpause=1 49 hint.arswitch.0.port.0.rxpause=1 50 51 # XXX OpenWRT DB120 BSP doesn't have media/duplex set? 52 hint.arge.0.phymask=0x0 53 hint.arge.0.media=1000 54 hint.arge.0.fduplex=1 55 hint.arge.0.miimode=3 # RGMII 56 hint.arge.0.pll_1000=0x06000000 57 58 # MAC for arge0 is the first 6 bytes of the ART 59 hint.arge.0.eeprommac=0x1f7f0000 60 61 # mdiobus1 on arge1 62 hint.argemdio.1.at="nexus0" 63 hint.argemdio.1.maddr=0x1a000000 64 hint.argemdio.1.msize=0x1000 65 hint.argemdio.1.order=0 66 67 # Embedded switch on the AR9344 68 # mdio1 is actually created as the AR8327 internal bus; so 69 # this pops up as mdio2. 70 hint.arswitch.1.at="mdio2" 71 hint.arswitch.1.is_7240=0 72 hint.arswitch.1.is_9340=1 73 hint.arswitch.1.numphys=5 74 hint.arswitch.1.phy4cpu=0 # phy 4 is not a "CPU port" PHY here 75 hint.arswitch.1.is_rgmii=0 76 hint.arswitch.1.is_gmii=1 # arge1 <-> switch PHY is GMII 77 78 # arge1 - lock up to 1000/full 79 hint.arge.1.phymask=0x0 # Nothing attached here (XXX?) 80 hint.arge.1.media=1000 81 hint.arge.1.fduplex=1 82 hint.arge.1.miimode=1 # GMII 83 84 # MAC for arge1 is the second 6 bytes of the ART 85 hint.arge.1.eeprommac=0x1f7f0006 86 87 # ART calibration data mapping - for the AR934x AHB device 88 hint.ar71xx_caldata.0.at="nexus0" 89 hint.ar71xx_caldata.0.order=0 90 # Where the ART is - last 64k in the first 8MB of flash 91 hint.ar71xx_caldata.0.map.0.ath_fixup_addr=0x1fff0000 92 hint.ar71xx_caldata.0.map.0.ath_fixup_size=16384 93 94 # And now tell the ath(4) driver where to look! 95 hint.ath.0.eeprom_firmware="ar71xx_caldata.0.map.0.eeprom_firmware" 96 97 # ath1: it's different; it's a PCIe attached device, so 98 # we instead need to teach the PCIe bridge code about it 99 # (ie, the 'early pci fixup' stuff that programs the PCIe 100 # host registers on the NIC) and then we teach ath where 101 # to find it. 102 103 # ath1 hint - pcie slot 0 104 hint.pcib.0.bus.0.0.0.ath_fixup_addr=0x1fff4000 105 hint.pcib.0.bus.0.0.0.ath_fixup_size=16384 106 107 # ath0 - eeprom comes from here 108 hint.ath.1.eeprom_firmware="pcib.0.bus.0.0.0.eeprom_firmware" 109 110 # flash layout: 111 # 112 # bootargs=console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),6336k(rootfs),1408k(uImage),64k(mib0),64k(ART) 113 114 # 256KiB u-boot 115 hint.map.0.at="flash/spi0" 116 hint.map.0.start=0x00000000 117 hint.map.0.end=0x00040000 # 256k u-boot 118 hint.map.0.name="u-boot" 119 hint.map.0.readonly=1 120 121 # 64KiB u-boot-env 122 hint.map.1.at="flash/spi0" 123 hint.map.1.start=0x00040000 124 hint.map.1.end=0x00050000 # 64k u-boot-env 125 hint.map.1.name="u-boot-env" 126 hint.map.1.readonly=1 127 128 # 6336KiB rootfs + 1344KiB uImage; turn into a single long 129 # combo image for FreeBSD. 130 131 hint.map.2.at="flash/spi0" 132 hint.map.2.start=0x00050000 133 hint.map.2.end="search:0x00050000:0x10000:.!/bin/sh" 134 hint.map.2.name="kernel" 135 hint.map.2.readonly=0 136 137 hint.map.3.at="flash/spi0" 138 hint.map.3.start="search:0x00050000:0x10000:.!/bin/sh" 139 hint.map.3.end=0x007d0000 140 hint.map.3.name="rootfs" 141 hint.map.3.readonly=0 142 143 # 64KiB cfg 144 hint.map.4.at="flash/spi0" 145 hint.map.4.start=0x007d0000 146 hint.map.4.end=0x007e0000 147 hint.map.4.name="cfg" 148 hint.map.4.readonly=0 149 150 # 64KiB mib0 151 hint.map.5.at="flash/spi0" 152 hint.map.5.start=0x007e0000 153 hint.map.5.end=0x007f0000 # 64k mib0 154 hint.map.5.name="mib0" 155 hint.map.5.readonly=1 156 157 # 64KiB ART 158 hint.map.6.at="flash/spi0" 159 hint.map.6.start=0x007f0000 160 hint.map.6.end=0x00800000 # 64k ART 161 hint.map.6.name="ART" 162 hint.map.6.readonly=1
Cache object: 8cbcd35414e9ddabaab4ce3fb25b831e
[ source navigation ] [ diff markup ] [ identifier search ] [ freetext search ] [ file search ] [ list types ] [ track identifier ]