The Design and Implementation of the FreeBSD Operating System, Second Edition
Now available: The Design and Implementation of the FreeBSD Operating System (Second Edition)


[ source navigation ] [ diff markup ] [ identifier search ] [ freetext search ] [ file search ] [ list types ] [ track identifier ]

FreeBSD/Linux Kernel Cross Reference
sys/mips/conf/DIR-825B1.hints

Version: -  FREEBSD  -  FREEBSD-13-STABLE  -  FREEBSD-13-0  -  FREEBSD-12-STABLE  -  FREEBSD-12-0  -  FREEBSD-11-STABLE  -  FREEBSD-11-0  -  FREEBSD-10-STABLE  -  FREEBSD-10-0  -  FREEBSD-9-STABLE  -  FREEBSD-9-0  -  FREEBSD-8-STABLE  -  FREEBSD-8-0  -  FREEBSD-7-STABLE  -  FREEBSD-7-0  -  FREEBSD-6-STABLE  -  FREEBSD-6-0  -  FREEBSD-5-STABLE  -  FREEBSD-5-0  -  FREEBSD-4-STABLE  -  FREEBSD-3-STABLE  -  FREEBSD22  -  l41  -  OPENBSD  -  linux-2.6  -  MK84  -  PLAN9  -  xnu-8792 
SearchContext: -  none  -  3  -  10 

    1 # $FreeBSD$
    2 
    3 # arge0 is connected to the LAN side of the switch PHY.
    4 # arge1 is connected to the single port WAN side of the switch PHY.
    5 
    6 hint.arge.0.phymask=0x0
    7 hint.arge.0.media=1000
    8 hint.arge.0.fduplex=1
    9 hint.arge.0.eeprommac=0x1f66ffa0
   10 hint.arge.0.readascii=1
   11 
   12 hint.arge.1.phymask=0x0
   13 hint.arge.1.media=1000
   14 hint.arge.1.fduplex=1
   15 hint.arge.1.eeprommac=0x1f66ffb4
   16 hint.arge.1.readascii=1
   17 
   18 # ath0 - slot 17
   19 hint.pcib.0.bus.0.17.0.ath_fixup_addr=0x1f661000
   20 hint.pcib.0.bus.0.17.0.ath_fixup_size=4096
   21 
   22 # ath1 - slot 18
   23 hint.pcib.0.bus.0.18.0.ath_fixup_addr=0x1f665000
   24 hint.pcib.0.bus.0.18.0.ath_fixup_size=4096
   25 
   26 # .. and now, telling each ath(4) NIC where to find the firmware
   27 # image.
   28 hint.ath.0.eeprom_firmware="pcib.0.bus.0.17.0.eeprom_firmware"
   29 hint.ath.1.eeprom_firmware="pcib.0.bus.0.18.0.eeprom_firmware"
   30 
   31 # Geom MAP
   32 
   33 # The DIR-825B1 has an 8MB flash part - HOWEVER, the 64k caldata isn't
   34 # at the end of the flash. It's ~ 6MB into the flash image.
   35 
   36 # mtdparts=ar7100-nor0:256k(uboot),64k(Config),1024k(vmlinux),5184k(rootfs),
   37 #          64k(caldata)
   38 
   39 hint.map.0.at="flash/spi0"
   40 hint.map.0.start=0x00000000
   41 hint.map.0.end=0x000040000
   42 hint.map.0.name="uboot"
   43 hint.map.0.readonly=1
   44 
   45 # This config partition is the D-Link specific configuration area.
   46 # I'm re-purposing it for FreeBSD.
   47 hint.map.1.at="flash/spi0"
   48 hint.map.1.start=0x00040000
   49 hint.map.1.end=0x00050000
   50 hint.map.1.name="cfg"
   51 hint.map.1.readonly=0
   52 
   53 hint.map.2.at="flash/spi0"
   54 hint.map.2.start=0x0050000
   55 hint.map.2.end="search:0x00050000:0x10000:.!/bin/sh"
   56 hint.map.2.name="kernel"
   57 hint.map.2.readonly=1
   58 
   59 hint.map.3.at="flash/spi0"
   60 hint.map.3.start="search:0x00050000:0x10000:.!/bin/sh"
   61 hint.map.3.end=0x00660000
   62 hint.map.3.name="rootfs"
   63 hint.map.3.readonly=0
   64 
   65 hint.map.4.at="flash/spi0"
   66 hint.map.4.start=0x00660000
   67 hint.map.4.end=0x00670000
   68 hint.map.4.name="art"
   69 hint.map.4.readonly=1
   70 
   71 # GPIO specific configuration block
   72 
   73 # Don't flip on anything that isn't already enabled.
   74 # This includes leaving the SPI CS1/CS2 pins as GPIO pins as they're
   75 # not used here.
   76 hint.gpio.0.function_set=0x00000000
   77 
   78 hint.gpio.0.function_clear=0x00000000
   79 
   80 # These are the GPIO LEDs and buttons which can be software controlled.
   81 hint.gpio.0.pinmask=0x000009ff
   82 
   83 # Pin 1  - USB (LED blue)     --> works
   84 # Pin 2  - Power (LED orange) --> works
   85 # Pin 3  - Power (LED blue)   --> works
   86 # Pin 4  - Button (RESET)     --> works
   87 # Pin 5  - WPS (LED blue)     --> works
   88 # Pin 6  - RTL8366RB switch data line
   89 # Pin 7  - Planet (LED orange)--> works
   90 # Pin 8  - RTL8366RB switch clock line
   91 # Pin 9  - Button (WPS)       --> works after set to high
   92 # Pin 10 - N/C
   93 # Pin 11 - N/C
   94 # Pin 12 - Planet (LED blue)  --> works
   95 
   96 # LEDs are configured separately and driven by the LED device
   97 # usb tested good
   98 hint.gpioled.0.at="gpiobus0"
   99 hint.gpioled.0.name="usb-blue"
  100 hint.gpioled.0.pins=0x0001
  101 
  102 # no orange power led?
  103 hint.gpioled.1.at="gpiobus0"
  104 hint.gpioled.1.name="power-orange"
  105 hint.gpioled.1.pins=0x0002
  106 
  107 # blue power tested good
  108 hint.gpioled.2.at="gpiobus0"
  109 hint.gpioled.2.name="power-blue"
  110 hint.gpioled.2.pins=0x0004
  111 
  112 # wps tested good
  113 hint.gpioled.3.at="gpiobus0"
  114 hint.gpioled.3.name="wps-blue"
  115 hint.gpioled.3.pins=0x0010
  116 
  117 # orage globe tested good
  118 hint.gpioled.4.at="gpiobus0"
  119 hint.gpioled.4.name="planet-orange"
  120 hint.gpioled.4.pins=0x0040
  121 
  122 # no blue planet LED on this unit
  123 hint.gpioled.5.at="gpiobus0"
  124 hint.gpioled.5.name="planet-blue"
  125 hint.gpioled.5.pins=0x0800
  126 
  127 # GPIO I2C bus
  128 hint.gpioiic.0.at="gpiobus0"
  129 hint.gpioiic.0.pins=0x00a0
  130 hint.gpioiic.0.sda=0
  131 hint.gpioiic.0.scl=1
  132 
  133 # I2C bus
  134 # Don't be strict about I2C protocol - the relaxed semantics are required
  135 # by the realtek switch PHY.
  136 hint.iicbus.0.strict=0
  137 
  138 # Bit bang bus - override default delay
  139 #hint.iicbb.0.udelay=3
  140 

Cache object: 07c1ceaf8800b1eb266aed9b32766d9c


[ source navigation ] [ diff markup ] [ identifier search ] [ freetext search ] [ file search ] [ list types ] [ track identifier ]


This page is part of the FreeBSD/Linux Linux Kernel Cross-Reference, and was automatically generated using a modified version of the LXR engine.