1 /* $NetBSD: lsi64854reg.h,v 1.5 2001/03/29 02:58:39 petrov Exp $ */
2
3 /*-
4 * Copyright (c) 1998 The NetBSD Foundation, Inc.
5 * All rights reserved.
6 *
7 * This code is derived from software contributed to The NetBSD Foundation
8 * by Paul Kranenburg.
9 *
10 * Redistribution and use in source and binary forms, with or without
11 * modification, are permitted provided that the following conditions
12 * are met:
13 * 1. Redistributions of source code must retain the above copyright
14 * notice, this list of conditions and the following disclaimer.
15 * 2. Redistributions in binary form must reproduce the above copyright
16 * notice, this list of conditions and the following disclaimer in the
17 * documentation and/or other materials provided with the distribution.
18 * 3. All advertising materials mentioning features or use of this software
19 * must display the following acknowledgement:
20 * This product includes software developed by the NetBSD
21 * Foundation, Inc. and its contributors.
22 * 4. Neither the name of The NetBSD Foundation nor the names of its
23 * contributors may be used to endorse or promote products derived
24 * from this software without specific prior written permission.
25 *
26 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
27 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
28 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
29 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
30 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
31 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
32 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
33 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
34 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
35 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
36 * POSSIBILITY OF SUCH DAMAGE.
37 */
38
39 /* $FreeBSD$ */
40
41 /*
42 * LSI 64854 DMA engine. Contains three independent channels
43 * designed to interface with (a) a NCR539X SCSI controller,
44 * (b) a AM7990 Ethernet controller, (c) Parallel port hardware..
45 */
46
47 /*
48 * Register offsets to bus handle.
49 */
50 #define L64854_REG_CSR 0 /* Control bits */
51 #define L64854_REG_ADDR 4 /* DMA Address */
52 #define L64854_REG_CNT 8 /* DMA count */
53 #define L64854_REG_CNT_MASK 0x00ffffff /* only 24 bits */
54 #define L64854_REG_ENBAR 12 /* ENET Base register */
55 #define L64854_REG_TEST 12 /* SCSI Test register */
56 #define L64854_REG_HCR 16 /* PP Hardware Configuration */
57 #define L64854_REG_OCR 18 /* PP Operation Configuration */
58 #define L64854_REG_DR 20 /* PP Data register */
59 #define L64854_REG_TCR 21 /* PP Transfer Control */
60 #define L64854_REG_OR 22 /* PP Output register */
61 #define L64854_REG_IR 23 /* PP Input register */
62 #define L64854_REG_ICR 24 /* PP Interrupt Control */
63
64
65 /*
66 * Control bits common to all three channels.
67 */
68 #define L64854_INT_PEND 0x00000001 /* Interrupt pending */
69 #define L64854_ERR_PEND 0x00000002 /* Error pending */
70 #define L64854_DRAINING 0x0000000c /* FIFO draining */
71 #define L64854_INT_EN 0x00000010 /* Interrupt enable */
72 #define L64854_INVALIDATE 0x00000020 /* Invalidate FIFO */
73 #define L64854_SLAVE_ERR 0x00000040 /* Slave access size error */
74 #define L64854_RESET 0x00000080 /* Reset device */
75 #define L64854_WRITE 0x00000100 /* 1: xfer to memory */
76 #define L64854_EN_DMA 0x00000200 /* enable DMA transfers */
77
78 #define L64854_BURST_SIZE 0x000c0000 /* Read/write burst size */
79 #define L64854_BURST_0 0x00080000 /* no bursts (SCSI-only) */
80 #define L64854_BURST_16 0x00000000 /* 16-byte bursts */
81 #define L64854_BURST_32 0x00040000 /* 32-byte bursts */
82 #define L64854_BURST_64 0x000c0000 /* 64-byte bursts (fas) */
83
84 #define L64854_RST_FAS366 0x08000000 /* FAS366 hardware reset */
85
86 #define L64854_DEVID 0xf0000000 /* device ID bits */
87
88 /*
89 * SCSI DMA control bits.
90 */
91 #define D_INT_PEND L64854_INT_PEND /* interrupt pending */
92 #define D_ERR_PEND L64854_ERR_PEND /* error pending */
93 #define D_DRAINING L64854_DRAINING /* fifo draining */
94 #define D_INT_EN L64854_INT_EN /* interrupt enable */
95 #define D_INVALIDATE L64854_INVALIDATE/* invalidate fifo */
96 #define D_SLAVE_ERR L64854_SLAVE_ERR/* slave access size error */
97 #define D_RESET L64854_RESET /* reset scsi */
98 #define D_WRITE L64854_WRITE /* 1 = dev -> mem */
99 #define D_EN_DMA L64854_EN_DMA /* enable DMA requests */
100 #define D_EN_CNT 0x00002000 /* enable byte counter */
101 #define D_TC 0x00004000 /* terminal count */
102 #define D_WIDE_EN 0x00008000 /* enable wide mode SBUS DMA (fas) */
103 #define D_DSBL_CSR_DRN 0x00010000 /* disable fifo drain on csr */
104 #define D_DSBL_SCSI_DRN 0x00020000 /* disable fifo drain on reg */
105
106 #define D_DIAG 0x00100000 /* disable fifo drain on addr */
107 #define D_TWO_CYCLE 0x00200000 /* 2 clocks per transfer */
108 #define D_FASTER 0x00400000 /* 3 clocks per transfer */
109 #define D_TCI_DIS 0x00800000 /* disable intr on D_TC */
110 #define D_EN_NEXT 0x01000000 /* enable auto next address */
111 #define D_DMA_ON 0x02000000 /* enable dma from scsi XXX */
112 #define D_DSBL_PARITY_CHK \
113 0x02000000 /* disable checking for parity on bus (default 1:fas) */
114 #define D_A_LOADED 0x04000000 /* address loaded */
115 #define D_NA_LOADED 0x08000000 /* next address loaded */
116 #define D_HW_RESET_FAS366 \
117 0x08000000 /* hardware reset FAS366 (fas) */
118 #define D_DEV_ID L64854_DEVID /* device ID */
119 #define DMAREV_0 0x00000000 /* Sunray DMA */
120 #define DMAREV_ESC 0x40000000 /* DMA ESC array */
121 #define DMAREV_1 0x80000000 /* 'DMA' */
122 #define DMAREV_PLUS 0x90000000 /* 'DMA+' */
123 #define DMAREV_2 0xa0000000 /* 'DMA2' */
124 #define DMAREV_HME 0xb0000000 /* 'HME' */
125
126 /*
127 * revisions 0,1 and ESC have different bits.
128 */
129 #define D_ESC_DRAIN 0x00000040 /* rev0,1,esc: drain fifo */
130 #define D_ESC_R_PEND 0x00000400 /* rev0,1: request pending */
131 #define D_ESC_BURST 0x00000800 /* DMA ESC: 16 byte bursts */
132 #define D_ESC_AUTODRAIN 0x00040000 /* DMA ESC: Auto-drain */
133
134 #define DDMACSR_BITS "\177\020" \
135 "b\00INT\0b\01ERR\0f\02\02DRAINING\0b\04IEN\0" \
136 "b\06SLVERR\0b\07RST\0b\10WRITE\0b\11ENDMA\0" \
137 "b\15ENCNT\0b\16TC\0\b\20DSBL_CSR_DRN\0" \
138 "b\21DSBL_SCSI_DRN\0f\22\2BURST\0b\25TWOCYCLE\0" \
139 "b\26FASTER\0b\27TCIDIS\0b\30ENNXT\0b\031DMAON\0" \
140 "b\32ALOADED\0b\33NALOADED\0"
141
142
143 /*
144 * ENET DMA control bits.
145 */
146 #define E_INT_PEND L64854_INT_PEND /* interrupt pending */
147 #define E_ERR_PEND L64854_ERR_PEND /* error pending */
148 #define E_DRAINING L64854_DRAINING /* fifo draining */
149 #define E_INT_EN L64854_INT_EN /* interrupt enable */
150 #define E_INVALIDATE L64854_INVALIDATE/* invalidate fifo */
151 #define E_SLAVE_ERR L64854_SLAVE_ERR/* slave access size error */
152 #define E_RESET L64854_RESET /* reset ENET */
153 #define E_reserved1 0x00000300 /* */
154 #define E_DRAIN 0x00000400 /* force Ecache drain */
155 #define E_DSBL_WR_DRN 0x00000800 /* disable Ecache drain on .. */
156 #define E_DSBL_RD_DRN 0x00001000 /* disable Ecache drain on .. */
157 #define E_reserved2 0x00006000 /* */
158 #define E_ILACC 0x00008000 /* ... */
159 #define E_DSBL_BUF_WR 0x00010000 /* no buffering of slave writes */
160 #define E_DSBL_WR_INVAL 0x00020000 /* no Ecache invalidate on slave writes */
161
162 #define E_reserved3 0x00100000 /* */
163 #define E_LOOP_TEST 0x00200000 /* loopback mode */
164 #define E_TP_AUI 0x00400000 /* 1 for TP, 0 for AUI */
165 #define E_reserved4 0x0c800000 /* */
166 #define E_DEV_ID L64854_DEVID /* ID bits */
167
168 #define EDMACSR_BITS "\177\020" \
169 "b\00INT\0b\01ERR\0f\02\02DRAINING\0b\04IEN\0" \
170 "b\06SLVERR\0b\07RST\0b\10WRITE\0b\12DRAIN\0" \
171 "b\13DSBL_WR_DRN\0b\14DSBL_RD_DRN\0b\17ILACC\0" \
172 "b\20DSBL_BUF_WR\0b\21DSBL_WR_INVAL\0" \
173 "b\25LOOPTEST\0b\26TP\0"
174
175 /*
176 * PP DMA control bits.
177 */
178 #define P_INT_PEND L64854_INT_PEND /* interrupt pending */
179 #define P_ERR_PEND L64854_ERR_PEND /* error pending */
180 #define P_DRAINING L64854_DRAINING /* fifo draining */
181 #define P_INT_EN L64854_INT_EN /* interrupt enable */
182 #define P_INVALIDATE L64854_INVALIDATE/* invalidate fifo */
183 #define P_SLAVE_ERR L64854_SLAVE_ERR/* slave access size error */
184 #define P_RESET L64854_RESET /* reset PP */
185 #define P_WRITE L64854_WRITE /* 1: xfer to memory */
186 #define P_EN_DMA L64854_EN_DMA /* enable DMA transfers */
187 #define P_reserved1 0x00001c00 /* */
188 #define P_EN_CNT 0x00002000 /* enable counter */
189 #define P_TC 0x00004000 /* terminal count */
190 #define P_reserved2 0x00038000 /* */
191
192 #define P_DIAG 0x00100000 /* ... */
193 #define P_reserved3 0x00600000 /* */
194 #define P_TCI_DIS 0x00800000 /* no interrupt on terminal count */
195 #define P_EN_NEXT 0x01000000 /* enable DMA chaining */
196 #define P_DMA_ON 0x02000000 /* DMA xfers enabled */
197 #define P_A_LOADED 0x04000000 /* addr and byte count valid */
198 #define P_NA_LOADED 0x08000000 /* next addr & count valid but not used */
199 #define P_DEV_ID L64854_DEVID /* ID bits */
200
201 #define PDMACSR_BITS "\177\020" \
202 "b\00INT\0b\01ERR\0f\02\02DRAINING\0b\04IEN\0" \
203 "b\06SLVERR\0b\07RST\0b\10WRITE\0b\11ENDMA\0" \
204 "b\15ENCNT\0b\16TC\0\b\24DIAG\0b\27TCIDIS\0" \
205 "b\30ENNXT\0b\031DMAON\0b\32ALOADED\0b\33NALOADED\0"
Cache object: d08fa0177c085f5ddd0e060c38c0d8d8
|